ASTM D692/D692M-09
(Specification)Standard Specification for Coarse Aggregate for Bituminous Paving Mixtures
Standard Specification for Coarse Aggregate for Bituminous Paving Mixtures
ABSTRACT
This specification covers coarse aggregates such as crushed stone, crushed hydraulic-cement concrete, crushed blast-furnace slag, crushed gravel, crushed expanded shale, crushed expanded clay, and crushed expanded slate suitable for use in bituminous paving mixtures. The aggregates shall consist of hard, strong, durable pieces, free of coherent coatings. They shall be sampled for testing, and shall conform to physical requirements as to bulk density, composition for both conventional and open graded friction course mixtures, polishing characteristics, soundness, and degradation behavior.
SCOPE
1.1 This specification covers crushed stone, crushed hydraulic-cement concrete, crushed blast-furnace slag, crushed gravel, crushed expanded shale, crushed expanded clay, and crushed expanded slate suitable for use in bituminous paving mixtures, as described in Specifications D 3515 or D 4215.
Note 1—Other slags having demonstrated a satisfactory service record may be used.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D692/D692M −09
StandardSpecification for
1
Coarse Aggregate for Bituminous Paving Mixtures
This standard is issued under the fixed designation D692/D692M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D8 Terminology Relating to Materials for Roads and Pave-
ments
1.1 This specification covers crushed stone, crushed
D75 Practice for Sampling Aggregates
hydraulic-cement concrete, crushed blast-furnace slag, crushed
D448 Classification for Sizes of Aggregate for Road and
gravel, crushed expanded shale, crushed expanded clay, and
Bridge Construction
crushed expanded slate suitable for use in bituminous paving
D3319 Practice for the Accelerated Polishing of Aggregates
mixtures, as described in Specifications D3515 or D4215.
Using the British Wheel
NOTE 1—Other slags having demonstrated a satisfactory service record
D3515 Specification for Hot-Mixed, Hot-Laid Bituminous
may be used.
3
Paving Mixtures (Withdrawn 2009)
1.2 The values stated in either SI units or inch-pound units
D3665 Practice for Random Sampling of Construction Ma-
are to be regarded separately as standard. The values stated in
terials
each system may not be exact equivalents; therefore, each
D4215 Specification for Cold-Mixed, Cold-Laid Bituminous
system shall be used independently of the other. Combining
Paving Mixtures
values from the two systems may result in non-conformance
D5821 Test Method for Determining the Percentage of
with the standard.
Fractured Particles in Coarse Aggregate
1.3 The text of this standard references notes and footnotes
3. Terminology
which provide explanatory material. These notes and footnotes
3.1 Definitions:
(excluding those in tables and figures) shall not be considered
3.1.1 For defining aggregate types, see Descriptive Nomen-
as requirements of the standard.
clature C294, and Terminology D8 and C125.
2. Referenced Documents
3.1.2 expanded shale, n; expanded clay, n; expanded slate,
2
n—the product resulting from the expanding of selected
2.1 ASTM Standards:
materials (shale, clay, or slate) in a rotary kiln at temperatures
C29/C29M Test Method for Bulk Density (“Unit Weight”)
over 1000°C [1832°F].
and Voids in Aggregate
C88 Test Method for Soundness of Aggregates by Use of
4. Ordering Information
Sodium Sulfate or Magnesium Sulfate
4.1 Orders for the material under this specification shall
C125 Terminology Relating to Concrete and Concrete Ag-
include the following information:
gregates
4.1.1 The specification designation and year of issue.
C131 Test Method for Resistance to Degradation of Small-
4.1.2 The size to be furnished (see 5.2).
Size CoarseAggregate byAbrasion and Impact in the Los
4.1.3 The quantity required.
Angeles Machine
4.1.4 Use of the coarse aggregate, whether for conventional
C136 Test Method for Sieve Analysis of Fine and Coarse
mixtures or open-graded friction course mixtures (see 5.4), and
Aggregates
whether for surface courses or base courses (see 5.7),
C294 Descriptive Nomenclature for Constituents of Con-
4.1.5 In the case of sulfate soundness tests (5.6), which salt
crete Aggregates
is to be used.
4.1.6 Any special requirements.
1
This specification is under the jurisdiction of ASTM Committee D04 on Road
and Paving Materials and is the direct responsibility of Subcommittee D04.50 on
5. Physical Requirements
Aggregate Specifications.
5.1 General—The coarse aggregate shall consist of hard,
Current edition approved June 1, 2009. Published June 2009. Originally
approved in 1942. Last previous edition approved in 2004 as D692 – 00 (2004).
strong, durable pieces, free of coherent coatings and conform-
DOI: 10.1520/D0692_D0692M-09.
ing to the requirements of this specification.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on The last approved version of this historical standard is referenced on
the ASTM website. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D692/D692M − 09
5.2 Grading: mixtures, shall be of a type known to possess adequate
5.2.1 The coarse aggregate grading shall conform to the resistance to the polishing action of the anticipated traffic. (see
requirements of Classification D448 for the size number Note 5)
designated, or to another grading as stated in the order (see
NOTE5—NostandardASTMmethodhasbeenrecognizedtobecapable
Note 2).
of defining
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D692–00 (Reapproved 2004) Designation: D 692/D 692M – 09
Standard Specification for
1
Coarse Aggregate for Bituminous Paving Mixtures
This standard is issued under the fixed designation D 692/D 692M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers crushed stone, crushed hydraulic-cement concrete, crushed blast-furnace slag, crushed gravel,
crushed expanded shale, crushed expanded clay, and crushed expanded slate suitable for use in bituminous paving mixtures, as
described in Specifications D 3515 or D 4215.
NOTE 1—Other slags having demonstrated a satisfactory service record may be used.
1.2The values stated in SI units are to be regarded as standard. Inch-pound units, shown in parentheses, are for information only.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes
(excluding those in tables and figures) shall not be considered as requirements of the standard.
2. Referenced Documents
2
2.1 ASTM Standards:
C 29/C 29M Test Method for Bulk Density (Unit Weight) and Voids in Aggregate
C88 Test Method for Soundness of Aggregates by Use of Sodium Sulfate or Magnesium Sulfate
C 125 Terminology Relating to Concrete and Concrete Aggregates
C 131 Test Method for Resistance to Degradation of Small-Size CoarseAggregate byAbrasion and Impact in the LosAngeles
Machine
C 136 Test Method for Sieve Analysis of Fine and Coarse Aggregates
C 294 Descriptive Nomenclature offor Constituents of Concrete Aggregates
D8 Terminology Relating to Materials for Roads and Pavements
D75 Practice for Sampling Aggregates
D 448 Classification for Sizes of Aggregate for Road and Bridge Construction
D 3319 Test Method Practice for the Accelerated Polishing of Aggregates Using the British Wheel
D 3515 Specification for Hot-Mixed, Hot-Laid Bituminous Paving Mixtures
D 3665 Practice for Random Sampling of Construction Materials
D 4215 Specification for Cold-Mixed, Cold-Laid Bituminous Paving Mixtures
D 5821 Test Method for Determining the Percentage of Fractured Particles in Coarse Aggregate
3. Terminology
3.1 Definitions:
3.1.1 For defining aggregate types, see Descriptive Nomenclature C 294, and Terminology D 8 and C 125.
3.1.2 expanded shale, n; expanded clay, n; expanded slate, n—the product resulting from the expanding of selected materials
(shale, clay, or slate) in a rotary kiln at temperatures over 1000°C [1832°F].
4. Ordering Information
4.1 Orders for the material under this specification shall include the following information:
1
ThisspecificationisunderthejurisdictionofASTMCommitteeD04onRoadandPavingMaterialsandisthedirectresponsibilityofSubcommitteeD04.50onAggregate
Specifications.
Current edition approved June 1, 2004.2009. Published June 2004.2009. Originally approved in 1942. Last previous edition approved in 20002004 as D 692 – 00 (2004).
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D 692/D 692M – 09
4.1.1 The specification designation and year of issue.
4.1.2 The size to be furnished (see 5.2).
4.1.3 The quantity required.
4.1.4 Use of the coarse aggregate, whether for conventional mixtures or open-graded friction course mixtures (see 5.4), and
whether for surface courses or base courses (see 5.7),
4.1.5 In the case of sulfate soundness tests (5.6), which salt is to be used.
4.1.6 Any special requirements.
5. Physical Requirements
5.1 General—The coarse aggregate shall consist of hard, strong, durable pieces, free of coherent coatings and conforming to
the requirements of this
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.