ASTM D4239-14e1
(Test Method)Standard Test Method for Sulfur in the Analysis Sample of Coal and Coke Using High-Temperature Tube Furnace Combustion
Standard Test Method for Sulfur in the Analysis Sample of Coal and Coke Using High-Temperature Tube Furnace Combustion
SIGNIFICANCE AND USE
4.1 Sulfur is part of the ultimate analysis of coal and coke.
4.2 Results of the sulfur analysis are used for evaluation of coal preparation and cleaning, evaluation of potential sulfur emissions from coal and coke combustion or conversion processes, and evaluation of coal and coke quality in relation to contract specifications, as well as for scientific purposes.
4.3 The competency of laboratories with respect to use of this standard can be established through reference to Practice D7448.
SCOPE
1.1 This test method covers the determination of sulfur in samples of coal or coke by high-temperature tube furnace combustion.
1.1.1 Two analysis methods are described.
1.2 When automated equipment is used, either method can be classified as an instrumental method.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 All percentages are percent mass fractions unless otherwise noted.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation: D4239 − 14
StandardTest Method for
Sulfur in the Analysis Sample of Coal and Coke Using High-
1
Temperature Tube Furnace Combustion
This standard is issued under the fixed designation D4239; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1
ε NOTE—Summary of Changes added and Tables 3 and A1.4 corrected editorially in November 2014.
1. Scope* D7448 Practice for Establishing the Competence of Labora-
tories Using ASTM Procedures in the Sampling and
1.1 This test method covers the determination of sulfur in
Analysis of Coal and Coke
samples of coal or coke by high-temperature tube furnace
D7582 Test Methods for Proximate Analysis of Coal and
combustion.
Coke by Macro Thermogravimetric Analysis
1.1.1 Two analysis methods are described.
E691 Practice for Conducting an Interlaboratory Study to
1.2 When automated equipment is used, either method can
Determine the Precision of a Test Method
3
be classified as an instrumental method.
2.2 ISO Standard:
1.3 The values stated in SI units are to be regarded as ISO 11722 Solid Mineral Fuels-Hard Coal – Determination
of Moisture in the general analysis test sample by drying
standard. No other units of measurement are included in this
standard. in nitrogen
1.4 All percentages are percent mass fractions unless other-
3. Summary of Test Method
wise noted.
3.1 Combustion Method A (1350°C)—A weighed test por-
1.5 This standard does not purport to address all of the
tion of sample is burned in a tube furnace at a minimum
safety concerns, if any, associated with its use. It is the
combustion tube operating temperature of 1350°C in a stream
responsibility of the user of this standard to establish appro-
of oxygen. During combustion at temperatures above 1350 ºC,
priate safety and health practices and determine the applica-
the sulfur and sulfur compounds contained in the sample are
bility of regulatory limitations prior to use.
decomposed and oxidized almost exclusively to gaseous sulfur
dioxide, SO . Moisture and particulates are removed from the
2
2. Referenced Documents
gas by filters. The gas stream is passed through a cell in which
2
2.1 ASTM Standards:
sulfur dioxide is measured by an infrared (IR) absorption
D346 Practice for Collection and Preparation of Coke
detector. Sulfur dioxide absorbs IR energy at a precise wave-
Samples for Laboratory Analysis
length within the IR spectrum. Energy is absorbed as the gas
D2013 Practice for Preparing Coal Samples for Analysis
passes through the cell body in which the IR energy is being
D3173 Test Method for Moisture in the Analysis Sample of
transmitted: thus, at the detector, less energy is received. All
Coal and Coke
other IR energy is eliminated from reaching the detector by a
D3176 Practice for Ultimate Analysis of Coal and Coke
precisewavelengthfilter.Thus,theabsorptionofIRenergycan
D3180 Practice for Calculating Coal and Coke Analyses
be attributed only to sulfur dioxide whose concentration is
from As-Determined to Different Bases
proportional to the change in energy at the detector. One cell is
used as both a reference and a measurement chamber. Total
sulfur as sulfur dioxide is detected on a continuous basis.
1
This test method is under the jurisdiction of ASTM Committee D05 on Coal
3.1.1 One procedure for Method A uses coal or coke
and Coke and is the direct responsibility of Subcommittee D05.21 on Methods of
reference materials to calibrate the sulfur analyzer. A second
Analysis.
procedure for Method A uses a pure substance, BBOT, to
Current edition approved March 1, 2014. Published March 2014. Originally
ε1
approved in 1983. Last previous edition approved in 2013 as D4239 – 13 . DOI:
calibrate the sulfur analyzer.
10.1520/D4239-14.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from International Organization for Standardization (ISO), 1, ch. de
Standards volume information, refer to the standard’s Document Summary page on la Voie-Creuse, Case postale 56, CH-1211, Geneva 20, Switzerland, http://
the ASTM website. www.iso.ch.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
´1
D4239 − 14
3.2 Combustion Method B (1150°C)—A weighed test por- 5. Sample
tion of sample is burned in a quartz combustion tube in a
5.1 Pul
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: D4239 − 14 D4239 − 14
Standard Test Method for
Sulfur in the Analysis Sample of Coal and Coke Using High-
1
Temperature Tube Furnace Combustion
This standard is issued under the fixed designation D4239; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1
ε NOTE—Summary of Changes added and Tables 3 and A1.4 corrected editorially in November 2014.
1. Scope Scope*
1.1 This test method covers the determination of sulfur in samples of coal or coke by high-temperature tube furnace combustion.
1.1.1 Two analysis methods are described.
1.2 When automated equipment is used, either method can be classified as an instrumental method.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 All percentages are percent mass fractions unless otherwise noted.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D346 Practice for Collection and Preparation of Coke Samples for Laboratory Analysis
D2013 Practice for Preparing Coal Samples for Analysis
D3173 Test Method for Moisture in the Analysis Sample of Coal and Coke
D3176 Practice for Ultimate Analysis of Coal and Coke
D3180 Practice for Calculating Coal and Coke Analyses from As-Determined to Different Bases
D7448 Practice for Establishing the Competence of Laboratories Using ASTM Procedures in the Sampling and Analysis of Coal
and Coke
D7582 Test Methods for Proximate Analysis of Coal and Coke by Macro Thermogravimetric Analysis
E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
3
2.2 ISO Standard:
ISO 11722 Solid Mineral Fuels-Hard Coal – Determination of Moisture in the general analysis test sample by drying in nitrogen
3. Summary of Test Method
3.1 Combustion Method A (1350°C)—A weighed test portion of sample is burned in a tube furnace at a minimum combustion
tube operating temperature of 1350°C in a stream of oxygen. During combustion at temperatures above 1350 ºC, the sulfur and
sulfur compounds contained in the sample are decomposed and oxidized almost exclusively to gaseous sulfur dioxide, SO .
2
Moisture and particulates are removed from the gas by filters. The gas stream is passed through a cell in which sulfur dioxide is
measured by an infrared (IR) absorption detector. Sulfur dioxide absorbs IR energy at a precise wavelength within the IR spectrum.
Energy is absorbed as the gas passes through the cell body in which the IR energy is being transmitted: thus, at the detector, less
energy is received. All other IR energy is eliminated from reaching the detector by a precise wavelength filter. Thus, the absorption
1
This test method is under the jurisdiction of ASTM Committee D05 on Coal and Coke and is the direct responsibility of Subcommittee D05.21 on Methods of Analysis.
ε1
Current edition approved March 1, 2014. Published March 2014. Originally approved in 1983. Last previous edition approved in 2013 as D4239 – 13 . DOI:
10.1520/D4239-14.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from International Organization for Standardization (ISO), 1, ch. de la Voie-Creuse, Case postale 56, CH-1211, Geneva 20, Switzerland, http://www.iso.ch.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
´1
D4239 − 14
of IR energy can be attributed only to sulfur dioxide whose concentration is proportional to the change in energy at the detector.
One cell is used as both a reference and a measurement chamber. Total sulfur as sulfur dioxide is detected on a continuous basis.
3.1.1 One procedure for Method A us
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.