iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D4126-02

(Specification)

Standard Specification for Vapor-Degreasing Grade and General Solvent Grade 1,1,1-Trichloroethane

Standard Specification for Vapor-Degreasing Grade and General Solvent Grade 1,1,1-Trichloroethane

SCOPE
1.1 This specification covers vapor-degreasing grade and general solvent grade 1,1,1-trichloroethane. High purity grades of 1,1,1-trichloroethane are available but should not be evaluated by this specification.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1—Practices D 3844 and D 4276, STP 403A and MNL2 provide additional important information on vapor degreasing and solvent properties.

General Information

Status
Historical
Publication Date
09-Dec-2002
ICS
71.100.99 - Other products of the chemical industry
Technical Committee
D26 - Halogenated Organic Solvents and Fire Extinguishing Agents
Drafting Committee
D26.02 - Vapor Degreasing
Current Stage
Ref Project

Relations

Replaces
ASTM D4126-00 - Standard Specification for Vapor-Degreasing Grade and General Solvent Grade 1,1,1-Trichloroethane
Effective Date
10-Dec-2002
Replaced By
ASTM D4126-02(2007) - Standard Specification for Vapor-Degreasing Grade and General Solvent Grade 1,1,1-Trichloroethane
Effective Date
01-Feb-2007

Buy Standard

ASTM D4126-02 - Standard Specification for Vapor-Degreasing Grade and General Solvent Grade 1,1,1-TrichloroethaneASTM D4126-02 - Standard Specification for Vapor-Degreasing Grade and General Solvent Grade 1,1,1-Trichloroethane
PreviousNext
Technical specification
ASTM D4126-02 - Standard Specification for Vapor-Degreasing Grade and General Solvent Grade 1,1,1-Trichloroethane
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D 4126 – 02
Standard Specification for
Vapor-Degreasing Grade and General Solvent Grade
1
1,1,1-Trichloroethane
This standard is issued under the fixed designation D 4126; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
5
1. Scope genated Organic Solvents and Their Admixtures
D 2989 Test Method for Acidity-Alkalinity of Halogenated
1.1 This specification covers vapor-degreasing grade and
5
Organic Solvents and Their Admixtures
general solvent grade 1,1,1-trichloroethane. High purity grades
D 3401 Test Methods for Water in Halogenated Organic
of 1,1,1-trichloroethane are available but should not be evalu-
5
Solvents and Their Admixtures
ated by this specification.
D 3741 Test Method for Appearance of Admixtures Con-
1.2 This standard does not purport to address all of the
5
taining Halogenated Organic Solvents
safety concerns, if any, associated with its use. It is the
D 3844 Practice for Labeling Halogenated Hydrocarbon
responsibility of the user of this standard to establish appro-
5
Solvent Containers
priate safety and health practices and determine the applica-
5
D 4276 Practice for Confined Area Entry
bility of regulatory limitations prior to use.
D 6806 Practice for Analysis of Halogenated Organic Sol-
2 3
5
NOTE 1—Practices D 3844 and D 4276, STP 403A and MNL2
vents and Their Admixtures by Gas Chromatography
provide additional important information on vapor degreasing and solvent
2.2 Other Documents:
properties.
29 CFR 1910.1200 Department of Labor, OSHA Regula-
6
tions, Hazard Communication
2. Referenced Documents
40 CFR 82 Environmental ProtectionAgency, Protection of
2.1 ASTM Standards:
6
Stratospheric Ozone
D 1078 Test Method for Distillation Range of Volatile
4 49 CFR 100 to 199 Department of Transportation Hazard-
Organic Liquids
6
ous Materials Regulations
D 2108 Test Method for Color of Halogenated Organic
5
Solvents and Their Admixtures (Platinum-Cobalt Scale)
3. Properties
D 2109 Test Methods for Nonvolatile Matter in Haloge-
3.1 Vapor degreasing grade and general solvent grade 1,1,1-
5
nated Organic Solvents and Their Admixtures
trichloroethane shall conform to the requirements prescribed in
D 2111 Test Methods for Specific Gravity of Halogenated
Table 1.
5
Organic Solvents and Their Admixtures
D 2942 Test Method for Total Acid Acceptance of Haloge-
4. Packaging
5
nated Organic Solvents (Nonreflux Methods)
4.1 Package and label industrial or commercial quantities in
D 2943 Method of Aluminum Scratch Test for 1,1,1-
accordance with DOT regulations in 49 CFR 100 to 199, in
5
Trichloroethane
accordance with state and local regulations, in accordance with
D 2988 Test Method for W
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D4081-16(2023)(Specification)
Standard Specification for Drycleaning-Grade Perchloroethylene

ABSTRACT
This specification covers dry cleaning-grade perchloroethylene suitable for use in the dry cleaning industry. Materials shall be tested and the individual grades shall conform to specified values of appearance, water content, residual odor, specific gravity, non-volatile residue content, boiling point, dry point, acid acceptance, and copper corrosion.
SCOPE
1.1 This specification covers drycleaning-grade perchloroethylene suitable for use in the drycleaning industry.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: Guide D3844 provides additional important information on proper labeling.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D4376-15(2020)(Specification)
Standard Specification for Vapor-Degreasing Grade Perchloroethylene

ABSTRACT
This specification covers the requirements and corresponding test methods for vapor-degreasing grade perchloroethylene. When tested, materials shall conform to the following physical properties: specific gravity; distillation range (initial boiling point and dry point); acidity as HCl; alkalinity as NaOH; water content; appearance; color in Pt-co units; halides content; nonvolatile residues content; acid acceptance; and copper corrosion behavior.
SCOPE
1.1 This specification covers vapor-degreasing grade perchloroethylene.2
Note 1: Guide D3844 and Practice D4276 provide additional important information on solvent properties.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6107-97(2023)(Specification)
Standard Specification for Stop-Leak Additive for Engine Coolants Used in Light Duty Service

ABSTRACT
This specification covers the requirements of a stop-leak additive to function effectively in automobile and light duty service. The stop-leak is intended to seal small leaks in engine cooling systems without adversely affecting heat transfer and fluid flow. The hole plugging capability, and foaming tendency of the stop-leak additive shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers the requirements of a stop-leak additive to function effectively in automobile and light duty service. The stop-leak is intended to seal small leaks in engine cooling systems without adversely affecting heat transfer and fluid flow.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D5678-17(2023)(Test Method)
Standard Test Method for Freeze/Thaw Resistance of Wax Emulsion Floor Polish

SIGNIFICANCE AND USE
3.1 This test method is used to determine the effect of freezing on wax emulsion floor polishes. It may be used to predict the stability of a floor polish in transit or when exposed to freezing, and whether or not the polish is damaged by freezing.
SCOPE
1.1 This test method covers the determination of the stability of wax emulsion floor polishes when these are exposed to repeated cycles of freezing and thawing. Possible degradation of the emulsion is observed and possible reduction of initial gloss is measured.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D1792-17(2023)(Test Method)
Standard Test Method for Long-Term Removability Properties of Emulsion Floor Polishes

SIGNIFICANCE AND USE
4.1 This test method is used to predict removability of floor polish after a treatment period that simulates aging in the field. It allows for uniform mechanical and detergent action leaving the only variable the actual removability of the polish.
SCOPE
1.1 This test method covers the determination of the relative ease of removal of dried films of water-emulsion floor polishes from common flooring substrates under accelerated conditions, which correspond to extended service aging.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3210-95(2023)(Test Method)
Standard Test Method for Comparing Colors of Films from Water-Emulsion Floor Polishes

SIGNIFICANCE AND USE
5.1 Whiteness index obtained from reflectance measurements on exaggerated dried polish films on filter paper can be used as a measurement of the color of such films.  
5.2 Whiteness index may be useful in predicting the potential discoloring effect of polish films on flooring substrates.  
5.3 Whiteness index should be useful in specifications when color comparisons are made with a standard sample polish.
SCOPE
1.1 This test method covers comparing colors of films (or solids) deposited from the emulsified particles in water emulsion floor polishes. It is based upon luminous reflectance measurements made with tristimulus colorimeters such as the Hunter Color Difference Meter.2  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D3209-93(2023)(Test Method)
Standard Test Method for Freeze/Thaw Resistance of Polymer Floor Polishes

SIGNIFICANCE AND USE
3.1 This test method is used to determine the effect of freezing on floor polishes. It may be used to predict the stability of a floor polish when exposed to freezing.
SCOPE
1.1 This test method covers the determination of the stability of polymer emulsion floor polishes when these are exposed to repeated cycles of freezing and thawing. Possible degradation of the emulsion is observed and possible reduction of initial gloss is measured.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D4002-81(2023)(Practice)
Standard Practice for Evaluation of Buffable Shoe Polish

SIGNIFICANCE AND USE
3.1 This practice is intended to define the properties to be tested, the apparatus to use, and the comparisons of product performance. It is recognized that considerable discretion exists among formulators and marketers of shoe polish on what properties or performance characteristics are best for their products. This practice will be flexible to honor this fact within the confines of the shoe polish definition in 2.1.
SCOPE
1.1 This practice covers the definition of properties to test and the apparatus to use, in evaluating the performance of buffable shoe polishes.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D1455-17(2023)(Test Method)
Standard Test Method for 60° Specular Gloss of Emulsion Floor Polish

SIGNIFICANCE AND USE
4.1 This test method may be used to evaluate the difference in gloss of dried films of emulsion floor polishes when the light reflected at a 60° angle is measured. Extremely high- or low-gloss polishes may not be differentiated at a 60° angle. A20° angle measured in accordance with Test Method D523 may give better definition of gloss.
SCOPE
1.1 This test method covers the determination of the 60° specular gloss of films of emulsion floor polish after application to a substrate.  
Note 1: Specular gloss is one of several related appearance attributes that produce the sensation of glossiness. For this reason, specular gloss measurements may not always correlate well with visual rankings of glossiness.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D4081-16(2023)(Specification)
Standard Specification for Drycleaning-Grade Perchloroethylene

ABSTRACT
This specification covers dry cleaning-grade perchloroethylene suitable for use in the dry cleaning industry. Materials shall be tested and the individual grades shall conform to specified values of appearance, water content, residual odor, specific gravity, non-volatile residue content, boiling point, dry point, acid acceptance, and copper corrosion.
SCOPE
1.1 This specification covers drycleaning-grade perchloroethylene suitable for use in the drycleaning industry.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: Guide D3844 provides additional important information on proper labeling.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off