ASTM D4067-11

Standard Classification System for and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods

ABSTRACT
This classification system covers reinforced and filled poly(phenylene sulfide) (PPS) materials suitable for injection molding and extrusion. This classification system is not intended for the selection of materials, but only as a means to call out plastic materials to be used for the manufacture of parts. The physical properties of the materials must meet the required tensile strength, flexural modulus, Izod impact strength, flexural strength, and density.
SCOPE
1.1 This classification system covers reinforced and filled poly(phenylene sulfide) materials suitable for injection molding and extrusion.
1.2 This classification system is not intended for the selection of materials, but only as a means to call out plastic materials to be used for the manufacture of parts. The selection of these materials shall be made by personnel with expertise in the plastics field where the environment, inherent properties of the materials, performance of the parts, part design, manufacturing process, and economics are considered.
1.3 The properties included in this classification system are those required to identify the compositions covered. If necessary, other requirements identifying particular characteristics important to specific applications shall be designated by using the suffixes given in Section 5 or Classification System D4000.
1.4 The values stated in SI units are to be regarded as the standard.
1.5 This precautionary statement pertains only to the test method portion of this classification system, Section 12. This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1—There is no known ISO equivalent to this standard.

General Information

• Status: Historical
• Publication Date: 31-Jan-2011
• ICS: 83.120 - Reinforced plastics
• Technical Committee: D20 - Plastics
• Drafting Committee: D20.15 - Thermoplastic Materials

Relations

• Replaces: ASTM D4067-10 - Standard Classification System for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods
• Effective Date: 01-Feb-2011
• Referred By: ASTM D4000-23 - Standard Classification System for Specifying Plastic Materials
• Effective Date: 01-Feb-2011
• Referred By: ASTM D6358-19e1 - Standard Classification System and Basis for Specification for Poly (Phenylene Sulfide) (PPS) Injection Molding, Extrusion and Blow Molding Materials Using ISO Methods
• Effective Date: 01-Feb-2011

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D4067 −11
StandardClassification System for and Basis for Specification for
Reinforced and Filled Poly(Phenylene Sulfide) (PPS)
Injection Molding and Extrusion Materials Using ASTM
1
Methods
This standard is issued under the fixed designation D4067; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* 2. Referenced Documents
2
1.1 This classification system covers reinforced and filled 2.1 ASTM Standards:
poly(phenylene sulfide) materials suitable for injection mold- D256 Test Methods for Determining the Izod Pendulum
ing and extrusion. Impact Resistance of Plastics
D618 Practice for Conditioning Plastics for Testing
1.2 This classification system is not intended for the selec-
D638 Test Method for Tensile Properties of Plastics
tion of materials, but only as a means to call out plastic
D648 Test Method for Deflection Temperature of Plastics
materials to be used for the manufacture of parts.The selection
Under Flexural Load in the Edgewise Position
of these materials shall be made by personnel with expertise in
D790 Test Methods for Flexural Properties of Unreinforced
the plastics field where the environment, inherent properties of
and Reinforced Plastics and Electrical Insulating Materi-
the materials, performance of the parts, part design, manufac-
als
turing process, and economics are considered.
D792 Test Methods for Density and Specific Gravity (Rela-
1.3 The properties included in this classification system are
tive Density) of Plastics by Displacement
those required to identify the compositions covered. If
D883 Terminology Relating to Plastics
necessary, other requirements identifying particular character-
D1238 Test Method for Melt Flow Rates of Thermoplastics
istics important to specific applications shall be designated by
by Extrusion Plastometer
using the suffixes given in Section 5 or Classification System
D1600 Terminology forAbbreviatedTerms Relating to Plas-
D4000.
tics
D3418 Test Method for Transition Temperatures and En-
1.4 The values stated in SI units are to be regarded as the
standard. thalpies of Fusion and Crystallization of Polymers by
Differential Scanning Calorimetry
1.5 This precautionary statement pertains only to the test
D3641 Practice for Injection Molding Test Specimens of
method portion of this classification system, Section 12. This
Thermoplastic Molding and Extrusion Materials
standard does not purport to address all of the safety concerns
D3835 Test Method for Determination of Properties of
associated with its use. It is the responsibility of the user of this
Polymeric Materials by Means of a Capillary Rheometer
standard to establish appropriate safety and health practices
D3892 Practice for Packaging/Packing of Plastics
and determine the applicability of regulatory limitations prior
D4000 Classification System for Specifying Plastic Materi-
to use.
als
NOTE 1—There is no known ISO equivalent to this standard.
D5630 Test Method for Ash Content in Plastics
E29 Practice for Using Significant Digits in Test Data to
Determine Conformance with Specifications
1
ThisclassificationsystemisunderthejurisdictionofASTMCommitteeD20on
Plastics and is the direct responsibility of Subcommittee D20.15 on Thermoplastic
2
Materials. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Feb. 1, 2011. Published March 2011. Originally contactASTM Customer Service at [e-mail]. ForAnnual Book ofASTM
approved in 1982. Last previous edition approved in 2010 as D4067 – 10. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/D4067-11. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D4067−11
NOTE 3—This part of the system uses the type and percentage of
E595 Test Method for Total Mass Loss and Collected Vola-
additive to designate the modification of the basic material. To facilitate
tile Condensable Materials from Outgassing in a Vacuum
this designation, the type and percentage of additive can be shown on the
Environment
supplier’s technical data sheet unless it is proprietary in nature. If
E662 Test Method for Specific Optical Density of Smoke
necessary, additional requirements shall be indicated by the use of the
Generated by Solid Materials
suffix part of the system, as given in Section 5. Special agreements
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D4067–10
Standard Classification System for Designation: D4067 – 11
Standard Classification System for and Basis for Specification
for
Reinforced and Filled Poly(Phenylene Sulfide) (PPS)
Injection Molding and Extrusion Materials Using ASTM
1
Methods
This standard is issued under the fixed designation D4067; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 This classification system covers reinforced and filled poly(phenylene sulfide) materials suitable for injection molding and
extrusion.
1.2 This classification system is not intended for the selection of materials, but only as a means to call out plastic materials to
be used for the manufacture of parts.The selection of these materials shall be made by personnel with expertise in the plastics field
where the environment, inherent properties of the materials, performance of the parts, part design, manufacturing process, and
economics are considered.
1.3 The properties included in this classification system are those required to identify the compositions covered. If necessary,
other requirements identifying particular characteristics important to specific applications shall be designated by using the suffixes
given in Section 5 or Classification System D4000.
1.4 The values stated in SI units are to be regarded as the standard.
1.5 This precautionary statement pertains only to the test method portion of this classification system, Section 12. This standard
does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard
to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
NOTE 1—There is no known ISO equivalent to this standard.
2. Referenced Documents
2
2.1 ASTM Standards:
D256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
D648 Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D883 Terminology Relating to Plastics
D1238 Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
D1600 Terminology for Abbreviated Terms Relating to Plastics
D3418 Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential
Scanning Calorimetry
1
This classification system is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.15 on Thermoplastic
Materials.
Current edition approved Sept. 15, 2010. Published September 2010. Originally approved in 1982. Last previous edition approved in 2003 as D4067–03. DOI:
10.1520/D4067-10.
Current edition approved Feb. 1, 2011. Published March 2011. Originally approved in 1982. Last previous edition approved in 2010 as D4067 – 10. DOI:
10.1520/D4067-11.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,[e-mail]ards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D4067 – 11
D3641 Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
D3835 Test Method for Determination of Properties of Polymeric Materials by Means of a Capillary Rheometer
D3892 Practice for Packaging/Packing of Plastics
D4000 Classification System for Specifying Plastic Materials
D5630 Test Method for Ash Content in Plastics
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E595 Test Method for Total Mass Loss and Collected Volatile Condensable Materials from Outgassing in a Vacuum
Environment
E662 Test Method for Speci
...