ASTM A450/A450M-15
(Specification)Standard Specification for General Requirements for Carbon and Low Alloy Steel Tubes
Standard Specification for General Requirements for Carbon and Low Alloy Steel Tubes
ABSTRACT
This specification covers carbon and low alloy steel tubes. Steel samples shall be melt processed and shall either be ingot cast or strand cast. Heat and product analyses shall be performed on the steel materials. Steel specimens shall also undergo tensile tests and shall conform to required values of yield strength and elongation. Flattening test, reverse flattening test, flaring test, flange test, hardness test, hydrostatic test, air underwater pressure test, and nondestructive tests shall be performed on the steel materials.
SCOPE
1.1 This specification2 covers a group of requirements which, with the exceptions of 6.3 and Sections 7, 8, 19, 20, 21, 22, 23, 24, and 25, are mandatory requirements to the following ASTM tubular product specifications:3
Title of Specification
ASTM DesignationA
Electric-Resistance-Welded Carbon Steel and Carbon Manganese Steel Boiler Tubes
A178/A178M
Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser Tubes
A179/A179M
Seamless Carbon Steel Boiler Tubes for High-Pressure Service
A192/A192M
Seamless Medium-Carbon Steel Boiler and Superheater Tubes
A210/A210M
Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes
A214/A214M
Seamless and Electric-Welded Low-Alloy Steel Tubes
A423/A423M
Specification for Seamless and Welded Carbon Steel Heat-Exchanger Tubes with Integral Fins
A498
Seamless Cold-Drawn Carbon Steel Feedwater Heater Tubes
A556/A556M
Seamless, Cold-Drawn Carbon Steel Tubing for Hydraulic System Service
A822/A822M(A) These designations refer to the latest issue of the respective specifications.
1.2 One or more of Sections 6.3, 7, 8, 19, 20, 21, 22, 22.1, 24, and 25 apply when the product specification or purchase order has a requirement for the test or analysis described by these sections.
1.3 In case of conflict between a requirement of the product specification and a requirement of this general requirement specification only the requirement of the product specification need be satisfied.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation (SI) of the product specification is specified in the order.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A450/A450M −15
Standard Specification for
General Requirements for Carbon and Low Alloy Steel
1
Tubes
This standard is issued under the fixed designationA450/A450M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* SI units are shown in brackets. The values stated in each
2 system may not be exact equivalents; therefore, each system
1.1 This specification covers a group of requirements
shall be used independently of the other. Combining values
which, with the exceptions of 6.3 and Sections 7, 8, 19, 20, 21,
from the two systems may result in non-conformance with the
22, 23, 24, and 25, are mandatory requirements to the follow-
3 standard. The inch-pound units shall apply unless the “M”
ing ASTM tubular product specifications:
designation (SI) of the product specification is specified in the
A
Title of Specification ASTM Designation
order.
Electric-Resistance-Welded Carbon Steel and Carbon A178/A178M
2. Referenced Documents
Manganese Steel Boiler Tubes
Seamless Cold-Drawn Low-Carbon Steel Heat- A179/A179M
4
2.1 ASTM Standards:
Exchanger and Condenser Tubes
Seamless Carbon Steel Boiler Tubes for High-Pressure A192/A192M A178/A178M Specification for Electric-Resistance-Welded
Service
Carbon Steel and Carbon-Manganese Steel Boiler and
Seamless Medium-Carbon Steel Boiler and Super- A210/A210M
Superheater Tubes
heater Tubes
Electric-Resistance-Welded Carbon Steel Heat- A214/A214M A179/A179M Specification for Seamless Cold-Drawn Low-
Exchanger and Condenser Tubes
Carbon Steel Heat-Exchanger and Condenser Tubes
Seamless and Electric-Welded Low-Alloy Steel Tubes A423/A423M
A192/A192M Specification for Seamless Carbon Steel
Specification for Seamless and Welded Carbon Steel A498
Heat-Exchanger Tubes with Integral Fins
Boiler Tubes for High-Pressure Service
Seamless Cold-Drawn Carbon Steel Feedwater Heater A556/A556M
A210/A210M Specification for Seamless Medium-Carbon
Tubes
Steel Boiler and Superheater Tubes
Seamless, Cold-Drawn Carbon Steel Tubing for Hy- A822/A822M
draulic System Service
A214/A214M Specification for Electric-Resistance-Welded
Carbon Steel Heat-Exchanger and Condenser Tubes
A
These designations refer to the latest issue of the respective specifications.
A370 Test Methods and Definitions for Mechanical Testing
1.2 One or more of Sections 6.3, 7, 8, 19, 20, 21, 22, 22.1,
of Steel Products
24, and 25 apply when the product specification or purchase
A423/A423M Specification for Seamless and Electric-
order has a requirement for the test or analysis described by
Welded Low-Alloy Steel Tubes
these sections.
A498 Specification for Seamless and Welded Carbon Steel
Heat-Exchanger Tubes with Integral Fins
1.3 In case of conflict between a requirement of the product
A530/A530M Specification for General Requirements for
specification and a requirement of this general requirement
Specialized Carbon and Alloy Steel Pipe
specification only the requirement of the product specification
A556/A556M Specification for Seamless Cold-Drawn Car-
need be satisfied.
bon Steel Feedwater Heater Tubes
1.4 The values stated in either SI units or inch-pound units
A700 Guide for Packaging, Marking, and Loading Methods
are to be regarded separately as standard. Within the text, the
for Steel Products for Shipment
A751 Test Methods, Practices, and Terminology for Chemi-
cal Analysis of Steel Products
1
This specification is under the jurisdiction ofASTM Committee A01 on Steel,
A822/A822M Specification for Seamless Cold-Drawn Car-
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
A01.09 on Carbon Steel Tubular Products.
bon Steel Tubing for Hydraulic System Service
Current edition approved May 1, 2015. Published June 2015. Originally
approved in 1961. Last previous edition approved in 2010 as A450/A450M–10.
4
DOI: 10.1520/A0450_A0450M-15. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi- contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
cation SA-450 in Section II of that Code. Standards volume information, refer to the standard’s Document Summary page on
3
Annual Book of ASTM Standards, Vols 01.01 and 01.04. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A450/A450M−15
A941 Terminolo
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A450/A450M − 10 A450/A450M − 15
Standard Specification for
General Requirements for Carbon and Low Alloy Steel
1
Tubes
This standard is issued under the fixed designation A450/A450M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
2
1.1 This specification covers a group of requirements which, with the exceptions of 5.36.3 and Sections 67, 78, 1819, 1920,
3
2021, 2122, 2223, 2324, and 2425, are mandatory requirements to the following ASTM tubular product specifications:
A
Title of Specification ASTM Designation
Electric-Resistance-Welded Carbon Steel and Carbon A178/A178M
Manganese Steel Boiler Tubes
Seamless Cold-Drawn Low-Carbon Steel Heat- A179/A179M
Exchanger and Condenser Tubes
Seamless Carbon Steel Boiler Tubes for High-Pressure A192/A192M
Service
Seamless Medium-Carbon Steel Boiler and Super- A210/A210M
heater Tubes
Electric-Resistance-Welded Carbon Steel Heat- A214/A214M
Exchanger and Condenser Tubes
Seamless and Electric-Welded Low-Alloy Steel Tubes A423/A423M
Specification for Seamless and Welded Carbon Steel A498
Heat-Exchanger Tubes with Integral Fins
Seamless Cold-Drawn Carbon Steel Feedwater Heater A556/A556M
Tubes
Seamless, Cold-Drawn Carbon Steel Tubing for Hy- A822/A822M
draulic System Service
A
These designations refer to the latest issue of the respective specifications.
1.2 One or more of Sections 5.36.3, 67, 78, 1819, 1920, 2021, 2122, 21.122.1, 2324, and 2425 apply when the product
specification or purchase order has a requirement for the test or analysis described by these sections.
1.3 In case of conflict between a requirement of the product specification and a requirement of this general requirement
specification only the requirement of the product specification need be satisfied.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units
are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used
independently of the other. Combining values from the two systems may result in non-conformance with the standard. The
inch-pound units shall apply unless the “M” designation (SI) of the product specification is specified in the order.
2. Referenced Documents
4
2.1 ASTM Standards:
A178/A178M Specification for Electric-Resistance-Welded Carbon Steel and Carbon-Manganese Steel Boiler and Superheater
Tubes
A179/A179M Specification for Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser Tubes
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.09
on Carbon Steel Tubular Products.
Current edition approved May 1, 2010May 1, 2015. Published June 2010June 2015. Originally approved in 1961. Last previous edition approved in 20092010 as
A450/A450M–09.–10. DOI: 10.1520/A0450_A0450M-10.10.1520/A0450_A0450M-15.
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SA-450 in Section II of that Code.
3
Annual Book of ASTM Standards, Vols 01.01 and 01.04.
4
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A450/A450M − 15
A192/A192M Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure Service
A210/A210M Specification for Seamless Medium-Carbon Steel Boiler and Superheater Tubes
A214/A214M Specification for Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A423/A423M Specification for Seamless and Electric-Welded Low-Alloy Steel Tubes
A498 Specification for Seamless and Welded Carbon Steel Heat-Exchanger Tubes with Integral Fins
A530/A530M Specification for General Requirements for Specialized Carbon and Allo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.