ASTM C1767-15
(Specification)Standard Specification for Stainless Steel Jacketing for Insulation
Standard Specification for Stainless Steel Jacketing for Insulation
ABSTRACT
This specification covers stainless steel jacketing for thermal, acoustical, and fire protective insulation operating at either above or below ambient temperatures and in both indoor and outdoor locations. It does not cover insulation jacketing made from other materials such as mastics, fiber reinforced plastic, PVC, aluminum, or coated carbon steel (for example, aluminum-zinc, galvanized steel, or aluminized steel) nor does it cover the details of thermal, acoustical, or fire protective insulation systems. While not intended to cover use inside the containment buildings of nuclear power plants, this specification does not preclude use of Class E material which does not have a moisture barrier in this containment building application. This specification provides physical requirements for stainless steel jacketing for thermal and acoustical insulation.
SCOPE
1.1 This specification covers stainless steel jacketing for thermal, acoustical, and fire protective insulation operating at either above or below ambient temperatures and in both indoor and outdoor locations. It does not cover insulation jacketing made from other materials such as mastics, fiber reinforced plastic, PVC, aluminum, or coated carbon steel (for example, aluminum-zinc, galvanized steel, or aluminized steel) nor does it cover the details of thermal, acoustical, or fire protective insulation systems.
1.2 While not intended to cover use inside the containment buildings of nuclear power plants, this standard does not preclude use of Class E material which does not have a moisture barrier in this containment building application.
1.3 This specification provides physical requirements for stainless steel jacketing for thermal and acoustical insulation. Guide C1423 provides guidance in selecting jacketing materials and their safe use.
1.4 This is a material specification and does not imply any performance of the installed system using the materials specified herein. For information about installation of stainless steel jacketing, see (1).2
1.5 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.6 A version of this standard in SI units is available as Specification C1767M.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C1767 −15
StandardSpecification for
1
Stainless Steel Jacketing for Insulation
This standard is issued under the fixed designation C1767; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
3
2.1 ASTM Standards:
1.1 This specification covers stainless steel jacketing for
A167 Specification for Stainless and Heat-Resisting
thermal, acoustical, and fire protective insulation operating at
Chromium-Nickel Steel Plate, Sheet, and Strip (With-
either above or below ambient temperatures and in both indoor
4
drawn 2014)
and outdoor locations. It does not cover insulation jacketing
A240/A240M Specification for Chromium and Chromium-
made from other materials such as mastics, fiber reinforced
Nickel Stainless Steel Plate, Sheet, and Strip for Pressure
plastic, PVC, aluminum, or coated carbon steel (for example,
Vessels and for General Applications
aluminum-zinc, galvanized steel, or aluminized steel) nor does
A480/A480M Specification for General Requirements for
it cover the details of thermal, acoustical, or fire protective
Flat-Rolled Stainless and Heat-Resisting Steel Plate,
insulation systems.
Sheet, and Strip
1.2 While not intended to cover use inside the containment
C168 Terminology Relating to Thermal Insulation
buildings of nuclear power plants, this standard does not
C450 Practice for Fabrication of Thermal Insulating Fitting
preclude use of Class E material which does not have a
Covers for NPS Piping, and Vessel Lagging
moisture barrier in this containment building application.
C585 Practice for Inner and Outer Diameters of Thermal
Insulation for Nominal Sizes of Pipe and Tubing
1.3 This specification provides physical requirements for
C835 Test Method for Total Hemispherical Emittance of
stainless steel jacketing for thermal and acoustical insulation.
Surfaces up to 1400°C
Guide C1423 provides guidance in selecting jacketing materi-
C1371 Test Method for Determination of Emittance of
als and their safe use.
Materials Near Room Temperature Using Portable Emis-
1.4 This is a material specification and does not imply any
someters
performance of the installed system using the materials speci-
C1423 Guide for Selecting Jacketing Materials for Thermal
fied herein. For information about installation of stainless steel
Insulation
2
jacketing, see (1).
C1729 Specification for Aluminum Jacketing for Insulation
C1785 Test Method for Concentration of Pinhole Detections
1.5 The values stated in inch-pound units are to be regarded
in Moisture Barriers on Metal Jacketing
as standard. No other units of measurement are included in this
E84 Test Method for Surface Burning Characteristics of
standard.
Building Materials
1.6 A version of this standard in SI units is available as
F1249 Test Method for Water Vapor Transmission Rate
Specification C1767M.
Through Plastic Film and Sheeting Using a Modulated
Infrared Sensor
1.7 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro- 3. Terminology
priate safety and health practices and determine the applica-
3.1 Definitions—Definitions in Terminology C168 apply to
bility of regulatory limitations prior to use.
terms used in this specification.
3.2 Definitions of Terms Specific to This Standard:
1
ThistestmethodisunderthejurisdictionofASTMCommitteeC16onThermal
Insulation and is the direct responsibility of Subcommittee C16.40 on Insulation
3
Systems. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Nov. 1, 2015. Published November 2015. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2012. Last previous edition approved in 2014 as C1767–14a. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/C1767-15. the ASTM website.
2 4
The boldface numbers in parentheses refer to the list of references at the end of The last approved version of this historical standard is referenced on
this standard. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1767−15
3.2.1 box rib—stainless steel sheet formed to have alternat- 3.2.13 safety hem—a rounded edge of metal jacketing cre-
ing parallel grooves and ridges with a cross section approxi- ated by folding the edge of sheet jacketing completely back
mating a square wave. upon itself using a roll former or a brake.
3.2.13.1 Disc
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1767 − 14a C1767 − 15
Standard Specification for
1
Stainless Steel Jacketing for Insulation
This standard is issued under the fixed designation C1767; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers stainless steel jacketing for thermal, acoustical, and fire protective insulation operating at either
above or below ambient temperatures and in both indoor and outdoor locations. It does not cover insulation jacketing made from
other materials such as mastics, fiber reinforced plastic, PVC, aluminum, or coated carbon steel (for example, aluminum-zinc,
galvanized steel, or aluminized steel) nor does it cover the details of thermal, acoustical, or fire protective insulation systems.
1.2 While not intended to cover use inside the containment buildings of nuclear power plants, this standard does not preclude
use of Class E material which does not have a moisture barrier in this containment building application.
1.3 This specification provides physical requirements for stainless steel jacketing for thermal and acoustical insulation. Guide
C1423 provides guidance in selecting jacketing materials and their safe use.
1.4 This is a material specification and does not imply any performance of the installed system using the materials specified
2
herein. For information about installation of stainless steel jacketing, see (1).
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered No other units of measurement are included
in this standard.
1.6 A version of this standard in SI units is available as Specification C1767M.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
4
A167 Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip (Withdrawn 2014)
A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and
for General Applications
A480/A480M Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip
C168 Terminology Relating to Thermal Insulation
C450 Practice for Fabrication of Thermal Insulating Fitting Covers for NPS Piping, and Vessel Lagging
C585 Practice for Inner and Outer Diameters of Thermal Insulation for Nominal Sizes of Pipe and Tubing
C835 Test Method for Total Hemispherical Emittance of Surfaces up to 1400°C
C1371 Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers
C1423 Guide for Selecting Jacketing Materials for Thermal Insulation
C1729 Specification for Aluminum Jacketing for Insulation
C1785 Test Method for Concentration of Pinhole Detections in Moisture Barriers on Metal Jacketing
E84 Test Method for Surface Burning Characteristics of Building Materials
F1249 Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor
1
This test method is under the jurisdiction of ASTM Committee C16 on Thermal Insulation and is the direct responsibility of Subcommittee C16.40 on Insulation Systems.
Current edition approved Sept. 1, 2014Nov. 1, 2015. Published October 2014November 2015. Originally approved in 2012. Last previous edition approved in 2014 as
C1767–14.–14a. DOI: 10.1520/C1767-14A.10.1520/C1767-15.
2
The boldface numbers in parentheses refer to the list of references at the end of this standard.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
The last approved version of this historical standard is referenced on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1767
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.