ASTM C1767-16a
(Specification)Standard Specification for Stainless Steel Jacketing for Insulation
Standard Specification for Stainless Steel Jacketing for Insulation
ABSTRACT
This specification covers stainless steel jacketing for thermal, acoustical, and fire protective insulation operating at either above or below ambient temperatures and in both indoor and outdoor locations. It does not cover insulation jacketing made from other materials such as mastics, fiber reinforced plastic, PVC, aluminum, or coated carbon steel (for example, aluminum-zinc, galvanized steel, or aluminized steel) nor does it cover the details of thermal, acoustical, or fire protective insulation systems. While not intended to cover use inside the containment buildings of nuclear power plants, this specification does not preclude use of Class E material which does not have a moisture barrier in this containment building application. This specification provides physical requirements for stainless steel jacketing for thermal and acoustical insulation.
SCOPE
1.1 This specification covers stainless steel jacketing for thermal, acoustical, and fire protective insulation operating at either above or below ambient temperatures and in both indoor and outdoor locations. It does not cover insulation jacketing made from other materials such as mastics, fiber reinforced plastic, PVC, aluminum, or coated carbon steel (for example, aluminum-zinc, galvanized steel, or aluminized steel) nor does it cover the details of thermal, acoustical, or fire protective insulation systems.
1.2 While not intended to cover use inside the containment buildings of nuclear power plants, this standard does not preclude use of Class E material which does not have a moisture barrier in this containment building application.
1.3 This specification provides physical requirements for stainless steel jacketing for thermal and acoustical insulation. Guide C1423 provides guidance in selecting jacketing materials and their safe use.
1.4 This is a material specification and does not imply any performance of the installed system using the materials specified herein. For information about installation of stainless steel jacketing, see (1).2
1.5 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.6 A version of this standard in SI units is available as Specification C1767M.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C1767 −16a
Standard Specification for
1
Stainless Steel Jacketing for Insulation
This standard is issued under the fixed designation C1767; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
3
2.1 ASTM Standards:
1.1 This specification covers stainless steel jacketing for
A167 Specification for Stainless and Heat-Resisting
thermal, acoustical, and fire protective insulation operating at
Chromium-Nickel Steel Plate, Sheet, and Strip (With-
either above or below ambient temperatures and in both indoor
4
drawn 2014)
and outdoor locations. It does not cover insulation jacketing
A240/A240M Specification for Chromium and Chromium-
made from other materials such as mastics, fiber reinforced
Nickel Stainless Steel Plate, Sheet, and Strip for Pressure
plastic, PVC, aluminum, or coated carbon steel (for example,
Vessels and for General Applications
aluminum-zinc, galvanized steel, or aluminized steel) nor does
A480/A480M Specification for General Requirements for
it cover the details of thermal, acoustical, or fire protective
Flat-Rolled Stainless and Heat-Resisting Steel Plate,
insulation systems.
Sheet, and Strip
1.2 While not intended to cover use inside the containment
B487 Test Method for Measurement of Metal and Oxide
buildings of nuclear power plants, this standard does not
Coating Thickness by Microscopical Examination of
preclude use of Class E material which does not have a
Cross Section
moisture barrier in this containment building application.
C168 Terminology Relating to Thermal Insulation
C450 Practice for Fabrication of Thermal Insulating Fitting
1.3 This specification provides physical requirements for
Covers for NPS Piping, and Vessel Lagging
stainless steel jacketing for thermal and acoustical insulation.
C585 Practice for Inner and Outer Diameters of Thermal
Guide C1423 provides guidance in selecting jacketing materi-
Insulation for Nominal Sizes of Pipe and Tubing
als and their safe use.
C835 Test Method for Total Hemispherical Emittance of
1.4 This is a material specification and does not imply any
Surfaces up to 1400°C
performance of the installed system using the materials speci-
C1371 Test Method for Determination of Emittance of
fied herein. For information about installation of stainless steel
Materials Near Room Temperature Using Portable Emis-
2
jacketing, see (1).
someters
C1423 Guide for Selecting Jacketing Materials for Thermal
1.5 The values stated in inch-pound units are to be regarded
Insulation
as standard. No other units of measurement are included in this
C1729 Specification for Aluminum Jacketing for Insulation
standard.
C1767M Specification for Stainless Steel Jacketing for In-
1.6 A version of this standard in SI units is available as
sulation
Specification C1767M.
C1785 Test Method for Concentration of Pinhole Detections
in Moisture Barriers on Metal Jacketing
1.7 This standard does not purport to address all of the
D3363 Test Method for Film Hardness by Pencil Test
safety concerns, if any, associated with its use. It is the
E84 Test Method for Surface Burning Characteristics of
responsibility of the user of this standard to establish appro-
Building Materials
priate safety and health practices and determine the applica-
F1249 Test Method for Water Vapor Transmission Rate
bility of regulatory limitations prior to use.
Through Plastic Film and Sheeting Using a Modulated
Infrared Sensor
1
This specification is under the jurisdiction of ASTM Committee C16 on
Thermal Insulation and is the direct responsibility of Subcommittee C16.40 on
3
Insulation Systems. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Sept. 1, 2016. Published September 2016. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2012. Last previous edition approved in 2016 as C1767 – 16. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/C1767-16A. the ASTM website.
2 4
The boldface numbers in parentheses refer to the list of references at the end of The last approved version of this historical standard is referenced on
this standard. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1767−16a
3. Terminology of one layer of ethylene/methacrylic acid copolymer and two
layers of other polymers, usually polyethylene.
3.1 Definitions—Definitions in Terminology C168 apply to
3.2.12 PVdF based paint system—a pigment
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1767 − 16 C1767 − 16a
Standard Specification for
1
Stainless Steel Jacketing for Insulation
This standard is issued under the fixed designation C1767; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers stainless steel jacketing for thermal, acoustical, and fire protective insulation operating at either
above or below ambient temperatures and in both indoor and outdoor locations. It does not cover insulation jacketing made from
other materials such as mastics, fiber reinforced plastic, PVC, aluminum, or coated carbon steel (for example, aluminum-zinc,
galvanized steel, or aluminized steel) nor does it cover the details of thermal, acoustical, or fire protective insulation systems.
1.2 While not intended to cover use inside the containment buildings of nuclear power plants, this standard does not preclude
use of Class E material which does not have a moisture barrier in this containment building application.
1.3 This specification provides physical requirements for stainless steel jacketing for thermal and acoustical insulation. Guide
C1423 provides guidance in selecting jacketing materials and their safe use.
1.4 This is a material specification and does not imply any performance of the installed system using the materials specified
2
herein. For information about installation of stainless steel jacketing, see (1).
1.5 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this
standard.
1.6 A version of this standard in SI units is available as Specification C1767M.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
4
A167 Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip (Withdrawn 2014)
A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and
for General Applications
A480/A480M Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip
B487 Test Method for Measurement of Metal and Oxide Coating Thickness by Microscopical Examination of Cross Section
C168 Terminology Relating to Thermal Insulation
C450 Practice for Fabrication of Thermal Insulating Fitting Covers for NPS Piping, and Vessel Lagging
C585 Practice for Inner and Outer Diameters of Thermal Insulation for Nominal Sizes of Pipe and Tubing
C835 Test Method for Total Hemispherical Emittance of Surfaces up to 1400°C
C1371 Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers
C1423 Guide for Selecting Jacketing Materials for Thermal Insulation
C1729 Specification for Aluminum Jacketing for Insulation
C1767M Specification for Stainless Steel Jacketing for Insulation
C1785 Test Method for Concentration of Pinhole Detections in Moisture Barriers on Metal Jacketing
D3363 Test Method for Film Hardness by Pencil Test
1
This specification is under the jurisdiction of ASTM Committee C16 on Thermal Insulation and is the direct responsibility of Subcommittee C16.40 on Insulation
Systems.
Current edition approved March 1, 2016Sept. 1, 2016. Published March 2016September 2016. Originally approved in 2012. Last previous edition approved in 20152016
as C1767 – 15.C1767 – 16. DOI: 10.1520/C1767-16.10.1520/C1767-16A.
2
The boldface numbers in parentheses refer to the list of references at the end of this standard.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
The last approved version of this historical standard is referenced on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1767 − 16a
E84 Test Method for Surface Burning Characteristics of Building Materials
F124
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.