Geometrical product specifications (GPS) - Dimensional tolerancing - Part 1: Linear sizes (ISO 14405-1:2016)

ISO 14405-1:2016 establishes the default specification operator (see ISO 17450‑2) for linear size and defines a number of special specification operators for linear size for features of size, e.g. "cylinder", "sphere", "torus,"[1], "circle", "two parallel opposite planes", or "two parallel opposite straight lines".
It also defines the specification modifiers and the drawing indications for these linear sizes.
It covers the following linear sizes:
a)    local size:
-      two-point size;
-      spherical size;
-      section size;
-      portion size;
b)    global size:
-      direct global linear size:
-      least-squares size;
-      maximum inscribed size;
-      minimum circumscribed size;
-      minimax size;
-      indirect global linear size;
c)    calculated size:
-      circumference diameter;
-      area diameter;
-      volume diameter;
d)    rank-order size:
-      maximum size;
-      minimum size;
-      average size;
-      median size;
-      mid-range size;
-      range of sizes;
-      standard deviation of sizes.
ISO 14405-1:2016 defines tolerances of linear sizes for the following:
-      a + and/or − limit deviation (e.g. 0/−0,019);
-      an upper limit of size (ULS) and/or lower limit of size (LLS) (e.g. 15,2 max., 12 min., or 30,2/30,181);
-      an ISO tolerance class code in accordance with ISO 286‑1 (e.g. 10 h6);
with or without modifiers.
ISO 14405-1:2016 provides a set of tools to express several types of size characteristic. It does not present any information on the relationship between a function or a use and a size characteristic.
[1]         A torus is a feature of size when its directrix diameter is fixed.

Geometrische Produktspezifikation (GPS) - Dimensionelle Tolerierung - Teil 1: Lineare Größenmaße (ISO 14405-1:2016)

Spécification géométrique des produits (GPS) - Tolérancement dimensionnel - Partie 1: Tailles linéaires (ISO 14405-1:2016)

L'ISO 14405-1 :2016 établit l'opérateur de spécification par défaut (voir l'ISO 17450‑2) pour la taille linéaire et définit un ensemble d'opérateurs de spécification spéciaux pour la taille linéaire des entités dimensionnelles de type «cylindre», «sphère», «tore»[1], «cercle», «deux plans parallèles opposés» ou «deux droites parallèles opposées».
Elle définit également les modificateurs de spécification et les indications relatives aux tailles linéaires à faire figurer sur les dessins.
Elle couvre les tailles linéaires suivantes:
a)    taille locale:
-      taille entre deux points;
-      taille sphérique;
-      taille dans une section;
-      taille sur une portion;
b)    taille globale:
-      taille linéaire globale directe;
-      taille des moindres carrés;
-      taille maximale inscrite;
-      taille minimale circonscrite;
-      taille du minimax;
-      taille linéaire globale indirecte;
c)    taille calculée:
-      diamètre circonférentiel;
-      diamètre d'aire (circulaire)[2];
-      diamètre d'un volume (de tronc de cylindre)[3];
d)    taille par ordre de rang:
-      taille maximale;
-      taille minimale;
-      taille moyenne;
-      taille médiane;
-      centre de la plage d'étendue;
-      étendue de tailles;
-      écart-type des tailles.
L'ISO 14405-1 :2016 définit les tolérances sur les tailles linéaires pour:
-      un écart limite positif et/ou négatif (par exemple 0/−0,019);
-      une limite supérieure de taille (ULS) et/ou une limite inférieure de taille (LLS) (par exemple 15,2 max., 12 min. ou 30,2/30,181);
-      un code ISO de classe de tolérance selon l'ISO 286‑1 (par exemple 10 h6);
avec ou sans modificateurs.
L'ISO 14405-1 :2016 fournit un ensemble d'outils pour exprimer plusieurs types de caractéristiques dimensionnelles. Elle ne donne aucune information sur la relation entre une fonction ou une utilisation et une caractéristique dimensionnelle.
[1] Un tore est une entité dimensionnelle lorsque le diamètre de sa directrice est fixé.
[2] Le terme «circulaire» entre parenthèses a été ajouté dans la version française pour une meilleure compréhension.
[3] Les termes «de tronc de cylindre» entre parenthèses ont été ajoutés dans la version française pour une meilleure compréhension.

Specifikacija geometrijskih veličin izdelka - Tolerance dimenzij - 1. del: Dolžinske mere (ISO 14405-1:2016)

Ta del standarda ISO 14405 določa privzet operator specifikacij (glej ISO 17450-2) za linearno velikost in določa številne posebne operatorje specifikacij za linearno velikost lastnosti velikosti, npr. »valja«, »krogle«, »torusa«1), »kroga«, »dveh vzporednih nasprotnih ravni« ali »dveh vzporednih nasprotnih ravnih črt«.
Določa tudi specifikacijske modifikatorje in risane oznake za te linearne velikosti.
Ta del standarda ISO 14405 opredeljuje naslednje linearne velikosti:
a) lokalna velikost:
— dvotočkovna velikost;
— sferična velikost;
— sekcijska velikost;
— porcijska velikost;
b) globalna velikost:
— neposredna globalna linearna velikost;
— velikost najmanjših kvadratkov;
— največja vrisana velikost;
— najmanjša obrisana velikost;
— največja najmanjša velikost;
— posredna globalna linearna velikost;
c) izračunana velikost:
— obodni premer;
— premer območja;
— premer prostornine;
1) Torus je lastnost velikosti, kadar je njegov premer fiksen.
d) velikost po vrstnem redu:
— največja velikost;
— najmanjša velikost;
— povprečna velikost;
— srednja velikost;
— velikost srednjega obsega;
— obseg velikosti;
— standardni odklon velikosti.
Ta del standarda ISO 14405 določa toleranco naslednjih linearnih velikosti:
— + in/ali − mejno odstopanje (npr. 0/−0,019) (glej sliko 11);
— zgornja omejitev velikosti (ULS) in/ali spodnja omejitev velikosti (LLS) (npr. 15,2 največ, 12 najmanj, ali 30,2/30,181) (glej sliko 13);
— tolerančna šifra razreda ISO v skladu s standardom ISO 286 1 (npr. 10 h6) (glej sliko 12);
z ali brez modifikatorjev (glej preglednici 1 in 2).
Ta del standarda ISO 14405 podaja načine izražanja številnih tipov lastnosti velikosti. Ne podaja nobenih informacij glede razmerja med funkcijo ali uporabo in lastnostjo velikosti.

General Information

Status
Published
Publication Date
30-Aug-2016
Withdrawal Date
27-Feb-2017
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
31-Aug-2016
Completion Date
31-Aug-2016

Relations

Buy Standard

Standard
EN ISO 14405-1:2016 (EN)
English language
64 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
EN ISO 14405-1:2016 (DE)
German language
64 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-november-2016
1DGRPHãþD
SIST EN ISO 14405-1:2012
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND7ROHUDQFHGLPHQ]LMGHO'ROåLQVNH
PHUH ,62
Geometrical product specifications (GPS) - Dimensional tolerancing - Part 1: Linear sizes
(ISO 14405-1:2016)
Geometrische Produktspezifikation (GPS) - Dimensionelle Tolerierung - Teil 1:
Längenmaße (ISO 14405-1:2016)
Spécification géométrique des produits (GPS) - Tolérancement dimensionnel - Partie 1:
Tailles linéaires (ISO 14405-1:2016)
Ta slovenski standard je istoveten z: EN ISO 14405-1:2016
ICS:
17.040.10 Tolerance in ujemi Limits and fits
17.040.40 6SHFLILNDFLMDJHRPHWULMVNLK Geometrical Product
YHOLþLQL]GHOND *36 Specification (GPS)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 14405-1
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2016
EUROPÄISCHE NORM
ICS 17.040.10 Supersedes EN ISO 14405-1:2010
English Version
Geometrical product specifications (GPS) - Dimensional
tolerancing - Part 1: Linear sizes (ISO 14405-1:2016)
Spécification géométrique des produits (GPS) - Geometrische Produktspezifikation (GPS) -
Tolérancement dimensionnel - Partie 1: Tailles Dimensionelle Tolerierung - Teil 1: Lineare
linéaires (ISO 14405-1:2016) Größenmaße (ISO 14405-1:2016)
This European Standard was approved by CEN on 15 January 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14405-1:2016 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 14405-1:2016) has been prepared by Technical Committee ISO/TC 213
“Dimensional and geometrical product specifications and verification” in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the
secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2017, and conflicting national standards
shall be withdrawn at the latest by February 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 14405-1:2010.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 14405-1:2016 has been approved by CEN as EN ISO 14405-1:2016 without any
modification.
INTERNATIONAL ISO
STANDARD 14405-1
Second edition
2016-08-15
Geometrical product specifications
(GPS) — Dimensional tolerancing —
Part 1:
Linear sizes
Spécification géométrique des produits (GPS) — Tolérancement
dimensionnel —
Partie 1: Tailles linéaires
Reference number
ISO 14405-1:2016(E)
©
ISO 2016
ISO 14405-1:2016(E)
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

ISO 14405-1:2016(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 Specification modifiers and symbols .16
5 Default specification operator for size .19
5.1 General .19
5.2 ISO default specification operator for size .20
5.3 Drawing-specific default specification operator for size .21
6 Drawing indication for special specification operators for size .22
6.1 Basic specification .22
6.1.1 General.22
6.1.2 Rules to indicate a basic GPS specification .22
6.1.3 Rules to indicate basic dimensional specification with modifiers .23
6.2 Indication of special specification operators .24
6.2.1 One specification operator for both limits (upper and lower) of a
size characteristic .24
6.2.2 Different specification operator for upper limit of size and lower limit of size .27
6.2.3 More than one dimensional specification applied to a linear feature of size .29
6.3 Tolerancing of fits on assembly drawings .30
7 Indication of the toleranced feature on which the size characteristic is defined .31
7.1 Complete toleranced linear feature of size .31
7.2 Specific fixed restricted portion of the feature of size .31
7.3 Any restricted portion of the feature of size of a specified length .32
7.4 Any cross section or any longitudinal section of a linear feature of size .33
7.5 Size characteristic in a specific cross section of a feature of size .35
7.6 Requirement applied individually for more than one feature of size .37
7.7 Requirement applied for more than one feature considered as one feature of size .38
7.8 Flexible/non-rigid parts .38
8 Complementary indication .39
Annex A (normative) Proportions and dimensions of graphical symbols .40
Annex B (informative) Overview diagram for linear size .42
Annex C (informative) Data handling with rank-order modifiers .43
Annex D (normative) Size characteristics .45
Annex E (normative) Graphical rules to locate and dimension the dimensional
specification elements .50
Annex F (informative) Relation to the GPS matrix model .54
Bibliography .56
ISO 14405-1:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 213, Dimensional and geometrical product
specification and verification.
This second edition cancels and replaces the first edition (ISO 14405-1:2010), which has been technically
revised.
The main changes from the previous edition are:
— Clauses 1 and 3, 5.3, 6.1, 6.2, 7.3, 7.8, T
...


SLOVENSKI STANDARD
01-november-2016
1DGRPHãþD
SIST EN ISO 14405-1:2012
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND7ROHUDQFHGLPHQ]LMGHO'ROåLQVNH
PHUH ,62
Geometrical product specifications (GPS) - Dimensional tolerancing - Part 1: Linear sizes
(ISO 14405-1:2016)
Geometrische Produktspezifikation (GPS) - Dimensionelle Tolerierung - Teil 1:
Längenmaße (ISO 14405-1:2016)
Spécification géométrique des produits (GPS) - Tolérancement dimensionnel - Partie 1:
Tailles linéaires (ISO 14405-1:2016)
Ta slovenski standard je istoveten z: EN ISO 14405-1:2016
ICS:
17.040.10 Tolerance in ujemi Limits and fits
17.040.40 6SHFLILNDFLMDJHRPHWULMVNLK Geometrical Product
YHOLþLQL]GHOND *36 Specification (GPS)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 14405-1
EUROPÄISCHE NORM
EUROPEAN STANDARD
August 2016
NORME EUROPÉENNE
ICS 17.040.10 Ersatz für EN ISO 14405-1:2010
Deutsche Fassung
Geometrische Produktspezifikation (GPS) - Dimensionelle
Tolerierung - Teil 1: Lineare Größenmaße (ISO 14405-
1:2016)
Geometrical product specifications (GPS) - Dimensional Spécification géométrique des produits (GPS) -
tolerancing - Part 1: Linear sizes (ISO 14405-1:2016) Tolérancement dimensionnel - Partie 1: Tailles linéaires
(ISO 14405-1:2016)
Diese Europäische Norm wurde vom CEN am 15. Januar 2016 angenommen.

Die CEN-Mitglieder sind gehalten, die CEN/CENELEC-Geschäftsordnung zu erfüllen, in der die Bedingungen festgelegt sind, unter
denen dieser Europäischen Norm ohne jede Änderung der Status einer nationalen Norm zu geben ist. Auf dem letzten Stand
befindliche Listen dieser nationalen Normen mit ihren bibliographischen Angaben sind beim Management-Zentrum des CEN-
CENELEC oder bei jedem CEN-Mitglied auf Anfrage erhältlich.

Diese Europäische Norm besteht in drei offiziellen Fassungen (Deutsch, Englisch, Französisch). Eine Fassung in einer anderen
Sprache, die von einem CEN-Mitglied in eigener Verantwortung durch Übersetzung in seine Landessprache gemacht und dem
Management-Zentrum mitgeteilt worden ist, hat den gleichen Status wie die offiziellen Fassungen.

CEN-Mitglieder sind die nationalen Normungsinstitute von Belgien, Bulgarien, Dänemark, Deutschland, der ehemaligen
jugoslawischen Republik Mazedonien, Estland, Finnland, Frankreich, Griechenland, Irland, Island, Italien, Kroatien, Lettland,
Litauen, Luxemburg, Malta, den Niederlanden, Norwegen, Österreich, Polen, Portugal, Rumänien, Schweden, der Schweiz, der
Slowakei, Slowenien, Spanien, der Tschechischen Republik, der Türkei, Ungarn, dem Vereinigten Königreich und Zypern.

EUROPÄISCHES KOMITEE FÜR NORMUNG
EUROPEAN COMMITTEE FOR STANDARDIZATION

COMITÉ EUROPÉEN DE NORMALISATION

CEN-CENELEC Management-Zentrum: Avenue Marnix 17, B-1000 Brüssel
© 2016 CEN Alle Rechte der Verwertung, gleich in welcher Form und in welchem Ref. Nr. EN ISO 14405-1:2016 D
Verfahren, sind weltweit den nationalen Mitgliedern von CEN
vorbehalten.
Inhalt
Seite
Europäisches Vorwort . 4
Vorwort . 5
Einleitung . 6
1 Anwendungsbereich . 7
2 Normative Verweisungen . 8
3 Begriffe . 9
4 Spezifikationsmodifikatoren und Symbole . 24
5 Default-Spezifikationsoperator für Größenmaße . 27
5.1 Allgemeines . 27
5.2 ISO-Default-Spezifikationsoperator für Größenmaße . 28
5.3 Zeichnungsspezifischer Default-Spezifikationsoperator für Größenmaße . 29
6 Zeichnungsangaben für spezielle Spezifikationsoperatoren für Größenmaße . 30
6.1 Grundlegende Spezifikation . 30
6.1.1 Allgemeines . 30
6.1.2 Regeln für die Angabe einer grundlegenden GPS-Spezifikation . 30
6.1.3 Regeln für die Angabe der grundlegenden Größenmaßspezifikation mit Modifikatoren . 31
6.2 Angabe spezieller Spezifikationsoperatoren . 33
6.2.1 Ein Spezifikationsoperator für beide Grenzen (obere und untere) eines
Größenmaßmerkmals . 33
6.2.2 Verschiedene Spezifikationsoperatoren für die obere Grenze des Größenmaßes und die
untere Grenze des Größenmaßes . 35
6.2.3 Anwendung von mehr als einer Größenmaßspezifikation auf ein lineares
Größenmaßelement . 36
6.3 Tolerierung von Passungen in Zusammenstellungszeichnungen . 38
7 Angabe des tolerierten Geometrieelementes für das das Größenmaßmerkmal definiert
wird . 38
7.1 Vollständiges toleriertes lineares Größenmaßelement . 38
7.2 Bestimmter fester eingeschränkter Teilbereich des Größenmaßelements . 39
7.3 Beliebiger, über eine spezifizierte Länge begrenzter Teilbereich des
Größenmaßelements . 40
7.4 Beliebiger Querschnitt oder beliebiger Längsschnitt eines linearen Größenmaßelements . 41
7.5 Größenmaßmerkmal in einem bestimmten Querschnitt eines Größenmaßelements . 43
7.6 Anforderung individuell angewendet für mehr als ein Größenmaßelement . 46
7.7 Anforderung angewendet für mehr als ein Geometrieelement, das als ein
Größenmaßelement betrachtet wird . 46
7.8 Flexible/nicht-formstabile Werkstücke. 46
8 Ergänzende Angabe . 47
Anhang A (normativ) Proportionen und Abmessungen graphischer Symbole . 48
Anhang B (informativ) Übersichtsdiagramm für lineare Größenmaße . 50
Anhang C (informativ) Handhabung von Daten mit Rangordnungsmodifikatoren . 51
Anhang D (normativ) Größenmaßmerkmale . 54
Anhang E (normativ) Graphische Regeln zum Bestimmen des Ortes und der Dimension von
dimensionalen Spezifikationselementen . 59
Anhang F (informativ) Zusammenhänge mit dem GPS-Matrix-Modell. 63
Literaturhinweise . 64

Europäisches Vorwort
Dieses Dokument (EN ISO 14405-1:2016) wurde vom Technischen Komitee ISO/TC 213 „Dimensional and
geometrical product specifications and verification“ in Zusammenarbeit mit dem Technischen Komitee
CEN/TC 290 „Geometrische Produktspezifikation und -prüfung“ erarbeitet, dessen Sekretariat vom AFNOR
gehalten wird.
Diese Europäische Norm muss den Status einer nationalen Norm erhalten, entweder durch Veröffentlichung
eines identischen Textes oder durch Anerkennung bis Februar 2017, und etwaige entgegenstehende
nationale Normen müssen bis Februar 2017 zurückgezogen werden.
Es wird auf die Möglichkeit hingewiesen, dass einige Elemente dieses Dokuments Patentrechte berühren
können. CEN [und/oder CENELEC] sind nicht dafür verantwortlich, einige oder alle diesbezüglichen
Patentrechte zu identifizieren.
Dieses Dokument ersetzt EN ISO 14405-1:2010.
Entsprechend der CEN-CENELEC-Geschäftsordnung sind die nationalen Normungsinstitute der folgenden
Länder gehalten, diese Europäische Norm zu übernehmen: Belgien, Bulgarien, Dänemark, Deutschland, die
ehemalige jugoslawische Republik Mazedonien, Estland, Finnland, Frankreich, Griechenland, Irland, Island,
Italien, Kroatien, Lettland, Litauen, Luxemburg, Malta, Niederlande, Norwegen, Österreich, Polen, Portugal,
Rumänien, Schweden, Schweiz, Slowakei, Slowenien, Spanien, Tschechische Republik, Türkei, Ungarn,
Vereinigtes Königreich und Zypern.
Anerkennungsnotiz
Der Text von ISO 14405-1:2016 wurde vom CEN als EN ISO 14405-1:2016 ohne irgendeine Abänderung
genehmigt.
Vorwort
ISO (die Internationale Organisation für Normung) ist eine weltweite Vereinigung von Nationalen
Normungsorganisationen (ISO-Mitgliedsorganisationen). Die Erstellung von Internationalen Normen wird
normalerweise von ISO Technischen Komitees durchgeführt. Jede Mitgliedsorganisation, die Interesse an
einem Thema hat, für welches ein Technisches Komitee gegründet wurde, hat das Recht, in diesem Komitee
vertreten zu sein. Internationale Organisationen, staatlich und nicht-staatlich, in Liaison mit ISO, nehmen
ebenfalls an der Arbeit teil. ISO arbeitet eng mit der Internationalen Elektrotechnischen Kommission (IEC)
bei allen elektrotechnischen Themen zusammen.
Die Verfahren, die bei der Entwicklung dieses Dokuments angewendet wurden und die für die weitere Pflege
vorgesehen sind, werden in den ISO/IEC-Direktiven, Teil 1 beschrieben. Im Besonderen sollten die für die
verschiedenen ISO-Dokumentenarten notwendigen Annahmekriterien beachtet werden. Dieses Dokument
wurde in Übereinstimmung mit den Gestaltungsregeln der ISO/IEC-Direktiven, Teil 2 erarbeitet (siehe
www.iso.org/directives).
Es wird auf die Möglichkeit hingewiesen, dass einige Elemente dieses Dokuments Patentrechte berühren
können. ISO ist nicht dafür verantwortlich, einige oder alle diesbezüglichen Patentrechte zu identifizieren.
Details zu allen während der Entwicklung des Dokuments identifizierten Patentrechten finden sich in der
Einleitung und/oder in der ISO-Liste der empfangenen Patenterklärungen (siehe www.iso.org/patents).
Jeder in diesem Dokument verwendete Handelsname wird als Information zum Nutzen der Anwender
angegeben und stellt keine Anerkennung dar.
Eine Erläuterung der Bedeutung ISO-spezifischer Benennungen und Ausdrücke, die sich auf
Konformitätsbewertung beziehen, sowie Informationen über die Beachtung der Grundsätze der
Welthandelsorganisation (WTO) zu technischen Handelshemmnissen (TBT, en: Technical Barriers to Trade)
durch ISO enthält der folgende Link: www.iso.org/iso/foreword.html.
Das für dieses Dokument verantwortliche Komitee ist ISO/TC 213, Dimensional and geometrical product
specification and verification.
Diese zweite Ausgabe ersetzt die erste Ausgabe (ISO 14405-1:2010), die technisch überarbeitet wurde.
Die wesentlichen Änderungen zur Vorgängerausgabe sind:
— Abschnitte 1 und 3, 5.3, 6.1, 7.3, 7.8, Tabellen 1 und 2 und die Bilder wurden technisch überarbeitet;
— Abschnitt 8 und Anhänge D und E wurden hinzugefügt.
ISO 14405 besteht aus folgenden Teilen unter dem allgemeinen Titel Geometrische Produktspezifikation
(GPS) — Dimensionelle Tolerierung:
— Teil 1: Lineare Größenmaße
— Teil 2: Andere als lineare Größenmaße
— Teil 3: Winkelgrößenmaße
Einleitung
Dieser Teil von ISO 14405 ist eine Norm für die Geometrische Produktspezifikation (GPS) und gilt als eine
allgemeine GPS-Norm (siehe ISO 14638). Er beeinflusst die Kettenglieder A bis C der Normenkette über
Größenmaß.
Das in ISO 14638 gegebene ISO-GPS-Matrix-Modell gibt einen Überblick über das ISO-GPS-System, dessen
Bestandteil dieser Teil von ISO 14405 ist. Die in ISO 8015 angegebenen grundlegenden ISO-GPS-Regeln
gelten für diesen Teil von ISO 14405, und die Default-Entscheidungsregeln nach ISO 14253-1 gelten für die
Spezifikationen nach diesem Teil von ISO 14405, sofern nicht anders angegeben.
Detailliertere Angaben zum Zusammenhang dieses Teils von ISO 14405 mit anderen Normen und dem
GPS-Matrix-Modell sind Anhang F zu en
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.