Dentistry - Extraction forceps - Part 1: General requirements (ISO 9173-1:2016)

ISO 9173-1:2016 specifies the general performance requirements for extraction forceps used in dentistry.

Zahnheilkunde - Extraktionszangen - Teil 1: Allgemeine Anforderungen (ISO 9173-1:2016)

Médecine bucco-dentaire - Daviers - Partie 1: Exigences générales (ISO 9173-1:2016)

ISO 9173-1:2016 spécifie les exigences de performance générales applicables aux daviers utilisés en médecine bucco-dentaire.

Zobozdravstvo - Klešče za ekstrakcijo - 1. del: Splošne zahteve (ISO 9173-1:2016)

Ta del standarda ISO 9173 določa splošne zahtevane lastnosti klešč za ekstrakcijo, ki se uporabljajo v zobozdravstvu.

General Information

Status
Published
Publication Date
29-Nov-2016
Technical Committee
Drafting Committee
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Due Date
30-Nov-2016
Completion Date
30-Nov-2016

RELATIONS

Buy Standard

Standard
EN ISO 9173-1:2017
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN ISO 9173-1:2017
01-februar-2017
1DGRPHãþD
SIST EN ISO 9173-1:2006
=RER]GUDYVWYR.OHãþH]DHNVWUDNFLMRGHO6SORãQH]DKWHYH ,62
Dentistry - Extraction forceps - Part 1: General requirements (ISO 9173-1:2016)
Zahnheilkunde - Extraktionszangen - Teil 1: Allgemeine Anforderungen (ISO 9173-
1:2016)

Médecine bucco-dentaire - Daviers - Partie 1: Exigences générales (ISO 9173-1:2016)

Ta slovenski standard je istoveten z: EN ISO 9173-1:2016
ICS:
11.060.20 =RERWHKQLþQDRSUHPD Dental equipment
SIST EN ISO 9173-1:2017 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 9173-1:2017
---------------------- Page: 2 ----------------------
SIST EN ISO 9173-1:2017
EN ISO 9173-1
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2016
EUROPÄISCHE NORM
ICS 11.060.20 Supersedes EN ISO 9173-1:2006
English Version
Dentistry - Extraction forceps - Part 1: General
requirements (ISO 9173-1:2016)

Médecine bucco-dentaire - Daviers - Partie 1: Zahnheilkunde - Extraktionszangen - Teil 1: Allgemeine

Exigences générales (ISO 9173-1:2016) Anforderungen (ISO 9173-1:2016)
This European Standard was approved by CEN on 20 August 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9173-1:2016 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 9173-1:2017
EN ISO 9173-1:2016 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

---------------------- Page: 4 ----------------------
SIST EN ISO 9173-1:2017
EN ISO 9173-1:2016 (E)
European foreword

This document (EN ISO 9173-1:2016) has been prepared by Technical Committee ISO/TC 106

"Dentistry" in collaboration with Technical Committee CEN/TC 55 “Dentistry” the secretariat of which

is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by May 2017, and conflicting national standards shall be

withdrawn at the latest by May 2017.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent

rights.
This document supersedes EN ISO 9173-1:2006.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,

France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.
Endorsement notice

The text of ISO 9173-1:2016 has been approved by CEN as EN ISO 9173-1:2016 without any

modification.
---------------------- Page: 5 ----------------------
SIST EN ISO 9173-1:2017
---------------------- Page: 6 ----------------------
SIST EN ISO 9173-1:2017
INTERNATIONAL ISO
STANDARD 9173-1
Third edition
2016-10-15
Dentistry — Extraction forceps —
Part 1:
General requirements
Médecine bucco-dentaire — Daviers —
Partie 1: Exigences générales
Reference number
ISO 9173-1:2016(E)
ISO 2016
---------------------- Page: 7 ----------------------
SIST EN ISO 9173-1:2017
ISO 9173-1:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 9173-1:2017
ISO 9173-1:2016(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Requirements .......................................................................................................................................................................................................... 2

4.1 Materials ....................................................................................................................................................................................................... 2

4.1.1 Component parts and fastening components ......................................................................................... 2

4.2 Maximum overall length ................................................................................................................................................................. 2

4.3 Rockwell hardness ............................................................................................................................................................................... 2

4.4 Surface finish ............................................................................................................................................................................................ 2

4.4.1 All surfaces ............................................................................................................................................................................ 2

4.4.2 Beaks .......................................................................................................................................................................................... 3

4.5 Resistance to reprocessing ........................................................................................................................................................... 3

4.6 Joint opening/closing force .......................................................................................................................................................... 3

4.7 Joint movement ...................................................................................................................................................................................... 3

5 Test methods ............................................................................................................................................................................................................. 3

5.1 Visual inspection ................................................................................................................................................................................... 3

5.2 Resistance to reprocessing .........................................
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.