EN ISO 10427-3:2004

Petroleum and natural gas industries - Equipment for well cementing - Part 3: Performance testing of cementing float equipment (ISO 10427-3:2003)

ISO 10427-3:2003 describes testing practices to evaluate the performance of cementing float equipment for the petroleum and natural gas industries.
ISO 10427-3:2003 is applicable to float equipment that will be in contact with water-based fluids used for drilling and cementing wells. It is not applicable to float equipment performance in non-water-based fluids.

Erdöl- und Erdgasindustrie - Ausrüstungen für die Bohrloch-Zementierung - Teil 3: Festigkeitsprüfung der Zementierung schwimmender Ausrüstungen (ISO 10427-3:2003)

Industries du pétrole et du gaz naturel - Equipement de cimentation de puits - Partie 3: Essais de performance des équipements de cimentation des cuvelages (ISO 10427-3:2003)

L'ISO 10427-3:2003 décrit les méthodes d'essai permettant d'évaluer les performances des équipements de cimentation des cuvelages pour les industries du pétrole et du gaz naturel.
L'ISO 10427-3:2003 s'applique aux équipements des cuvelages en contact avec les fluides à base d'eau utilisés pour le forage et la cimentation des puits. Elle ne s'applique pas aux performances des équipements des cuvelages utilisés avec des fluides non à base d'eau.

Industrija za predelavo nafte in zemeljskega plina – Oprema za cementiranje vrtin – 3. del: Preskušanje lastnosti opreme za cementiranje plavajočih struktur (ISO 10427-3:2003)

General Information

• Status: Published
• Publication Date: 26-Oct-2004
• Withdrawal Date: 29-Apr-2005
• ICS: 75.180.10 - Exploratory, drilling and extraction equipment
• Technical Committee: CEN/TC 12 - Materials, equipment and offshore structures for petroleum and natural gas industries
• Drafting Committee: CEN/TC 12 - Materials, equipment and offshore structures for petroleum and natural gas industries
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Start Date: 14-Mar-2009
• Completion Date: 14-Mar-2009
• Ref Project: SIST EN ISO 10427-3:2005 - Petroleum and natural gas industries - Equipment for well cementing - Part 3: Performance testing of cementing float equipment (ISO 10427-3:2003)

Standards Content (Sample)

SLOVENSKI STANDARD
01-marec-2005
,QGXVWULMD]DSUHGHODYRQDIWHLQ]HPHOMVNHJDSOLQD±2SUHPD]DFHPHQWLUDQMHYUWLQ±
GHO3UHVNXãDQMHODVWQRVWLRSUHPH]DFHPHQWLUDQMHSODYDMRþLKVWUXNWXU,62

Petroleum and natural gas industries - Equipment for well cementing - Part 3:
Performance testing of cementing float equipment (ISO 10427-3:2003)
Erdöl- und Erdgasindustrie - Ausrüstungen für die Bohrloch-Zementierung - Teil 3:
Festigkeitsprüfung der Zementierung schwimmender Ausrüstungen (ISO 10427-3:2003)
Industries du pétrole et du gaz naturel - Equipement de cimentation de puits - Partie 3:
Essais de performance des équipements de cimentation des cuvelages (ISO 10427-
3:2003)
Ta slovenski standard je istoveten z: EN ISO 10427-3:2004
ICS:
75.180.10 Oprema za raziskovanje in Exploratory and extraction
odkopavanje equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 10427-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2004
ICS 75.180.10
English version
Petroleum and natural gas industries - Equipment for well
cementing - Part 3: Performance testing of cementing float
equipment (ISO 10427-3:2003)
Industries du pétrole et du gaz naturel - Equipement de Erdöl- und Erdgasindustrie - Ausrüstungen für die Bohrlock-
cimentation de puits - Partie 3: Essais de performance des Zementierung - Teil 3: Festigkeitsprüfung der Zementierung
équipements de cimentation des cuvelages (ISO 10427- schwimmender Ausrüstungen (ISO 10427-3:2003)
3:2003)
This European Standard was approved by CEN on 30 September 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10427-3:2004: E
worldwide for CEN national Members.

Foreword
The text of ISO 10427-3:2003 has been prepared by Technical Committee ISO/TC 67
"Materials, equipment and offshore structures for petroleum and natural gas industries" of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 10427-
3:2004 by Technical Committee CEN/TC 12 "Materials, equipment and offshore structures for
petroleum and natural gas industries" the secretariat of which is held by AFNOR.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by April 2005, and conflicting national
standards shall be withdrawn at the latest by April 2005.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Endorsement notice
The text of ISO 10427-3:2003 has been approved by CEN as EN ISO 10427-3:2004 without any
modifications.
INTERNATIONAL ISO
STANDARD 10427-3
First edition
2003-04-01
Petroleum and natural gas industries —
Equipment for well cementing —
Part 3:
Performance testing of cementing float
equipment
Industries du pétrole et du gaz naturel — Matériel pour la cimentation
des puits —
Partie 3: Mode opératoire des tests des équipements de cimentation
des cuvelages
Reference number
ISO 10427-3:2003(E)
©
ISO 2003
ISO 10427-3:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2003 — All rights reserved

ISO 10427-3:2003(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Functions of cementing float equipment. 1
3 Float equipment performance criteria . 2
3.1 General. 2
3.2 Durability under downhole conditions . 2
3.3 Differential pressure capability from below . 2
3.4 Ability to withstand force exerted through cementing plugs from above . 2
3.5 Drillability of the equipment. 2
3.6 Ability to pass lost circulation materials . 2
3.7 Flow coefficient of the valve . 2
3.8 Reverse-flow resistance of casing fill-up valves . 2
4 Apparatus and materials. 3
4.1 Flow loop. 3
4.2 Circulating test fluid . 4
4.3 High-temperature/high-pressure test cell. 5
5 Durability test. 7
5.1 Test set-up. 7
5.2 Test categories. 7
5.3 Procedure. 8
6 Static high-temperature/high-pressure test . 8
6.1 Test categories. 8
6.2 Procedure. 9
7 Test results. 9
Annex A (informative) Results of performance tests on cementing float equipment . 10
Bibliography . 11

ISO 10427-3:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10427-3 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures
for petroleum, petrochemical and natural gas industries, Subcommittee SC 3, Drilling and completion fluids,
and well cements.
This first edition cancels and replaces the first edition of ISO 18165, which has undergone an ISO number
change and a minor revision.
ISO 10427 consists of the following parts, under the general title Petroleum and natural gas industries —
Equipment for well cementing:
 Part 1: Casing bow-spring centralizers
 Part 2: Centralizer placement and stop-collar testing
 Part 3: Performance testing of cementing float equipment
iv © ISO 2003 — All rights reserved

ISO 10427-3:2003(E)
Introduction
This part of ISO 10427 is based on API Recommended Practice 10F, second edition, November, 1995.
Users of this part of ISO 10427 should be aware that further or differing requirements may be needed for
individual applications. This part of ISO 10427 is not intended to inhibit a vendor from offering, or the
purchaser from accepting, alternative equipment or engineering solutions for the individual application. This
may be particularly applicable where there is innovative or developing technology. Where an alternative is
offered, the vendor should identify any variations from this part of ISO 10427 and provide details.
In this part of ISO 10427, where practical, U.S. Customary units are included in brackets for information.

INTERNATIONAL STANDARD ISO 10427-3:2003(E)

Petroleum and natural gas industries — Equipment for well
cementing —
Part 3:
Performance testing of cementing float equipment
1 Scope
This part of ISO 10427 describes testing practices to evaluate the performance of cementing float equipment
for the petroleum and natural gas industries.
This part of ISO 10427 is applicable to float equipment that will be in contact with water-based fluids used for
drilling and cementing wells. It is not applicable to float equipment performance in non-water-based fluids.
2 Functions of cementing float equipment
The term “cementing float equipment” refers to one or more check valves incorporated into a well casing string
that prevent fluid flow up the casing while allowing fluid flow down the casing. The primary purpose of
cementing float equipment is to prevent cement that has been placed in the casing/wellbore annulus from
flowing up the casing (U-tubing). In some cases, such as liner cementing, float equipment may be the only
practical m
...