prEN ISO 8611-1
(Main)Pallets for materials handling - Flat pallets - Part 1: Test methods (ISO/DIS 8611-1:2024)
Pallets for materials handling - Flat pallets - Part 1: Test methods (ISO/DIS 8611-1:2024)
This document specifies the test methods available for evaluating new flat pallets for materials handling.
The test methods are split into groups for:
— nominal load testing;
— maximum working load testing;
— durability comparison testing.
This document does not apply to pallets with a fixed superstructure or a rigid, self-supporting container that can be mechanically attached to the pallet and which contributes to the strength of the pallet.
NOTE Specific tests for determining load capacity do not replace the value of conducting field tests on specific pallet designs.
Paletten für den Gütertransport - Flachpaletten - Teil 1: Prüfverfahren (ISO/DIS 8611‑1:2024)
Palettes pour la manutention - Palettes plates - Partie 1: Méthodes d'essai (ISO/DIS 8611-1:2024)
Le présent document spécifie les méthodes d’essai disponibles pour l’évaluation de palettes plates neuves pour la manutention.
Les méthodes d’essai sont réparties en groupes selon:
— les essais de la charge nominale;
— les essais de la charge maximale en service;
— les essais comparatifs en matière de durabilité.
Le présent document ne s’étend pas aux palettes à superstructure fixe ou à conteneur autoportant rigide pouvant être fixés mécaniquement à la palette et contribuant à sa résistance.
NOTE Des essais spécifiques pour déterminer la charge nominale ne sauraient remplacer la valeur d’essais en conditions réelles d’utilisation pour des types de palettes spécifiques.
Palete za ravnanje z materiali - Ravne palete - 1. del: Preskusne metode (ISO/DIS 8611-1:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2024
Palete za ravnanje z materiali - Ravne palete - 1. del: Preskusne metode (ISO/DIS
8611-1:2024)
Pallets for materials handling - Flat pallets - Part 1: Test methods (ISO/DIS 8611-1:2024)
Paletten für den Gütertransport - Flachpaletten - Teil 1: Prüfverfahren (ISO/DIS 8611-
1:2024)
Palettes pour la manutention - Palettes plates - Partie 1: Méthodes d'essai (ISO/DIS
8611-1:2024)
Ta slovenski standard je istoveten z: prEN ISO 8611-1
ICS:
55.180.20 Večnamenske palete General purpose pallets
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT INTERNATIONAL STANDARD
ISO/DIS 8611-1
ISO/TC 51 Secretariat: BSI
Voting begins on: Voting terminates on:
2024-01-22 2024-04-15
Pallets for materials handling — Flat pallets —
Part 1:
Test methods
Palettes pour la manutention — Palettes plates —
Partie 1: Méthodes d'essai
ICS: 55.180.20
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 8611-1:2024(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2024
ISO/DIS 8611-1:2024(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 8611-1
ISO/TC 51 Secretariat: BSI
Voting begins on: Voting terminates on:
Pallets for materials handling — Flat pallets —
Part 1:
Test methods
Palettes pour la manutention — Palettes plates —
Partie 1: Méthodes d'essai
ICS: 55.180.20
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2024
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 8611-1:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
ISO/DIS 8611-1:2023(E)
Contents Page
Foreword .v
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Measurements .3
5 Precision and accuracy of tests and apparatus . 3
6 Test load . 3
7 List of tests .4
8 Tests . 4
8.1 Test 1 — Bending tests . 4
8.1.1 Purpose . 4
8.1.2 Procedure . 5
8.1.3 Measurements . 6
8.2 Test 2 — Forklifting tests . 7
8.2.1 Purpose . 7
8.2.2 Procedure . 7
8.2.3 Measurement . 9
8.3 Test 3 — Compression tests for blocks or stringers . 9
8.3.1 Purpose . 9
8.3.2 Procedure . 9
8.3.3 Measurement . 10
8.4 Test 4 — Stacking test . 11
8.4.1 Purpose . 11
8.4.2 Procedure . 11
8.4.3 Measurement .12
8.5 Test 5 — Bottom deck bending tests .12
8.5.1 Purpose .12
8.5.2 Procedure . 12
8.5.3 Measurement .13
8.6 Test 6 — Wing pallet bending tests . 14
8.6.1 Purpose . 14
8.6.2 Procedure . 14
8.6.3 Measurements .15
8.7 Test 7 — Airbag bending tests .15
8.7.1 Purpose .15
8.7.2 Procedure . 15
8.7.3 Measurement . 18
8.8 Test 8 — Static shear test . 18
8.8.1 Purpose . 18
8.8.2 Procedure . 18
8.8.3 Measurement . 19
8.9 Test 9 — Corner drop test . 19
8.9.1 Purpose . 19
8.9.2 Procedure . 19
8.9.3 Measurement . 20
8.10 Test 10 — Shear impact tests . 20
8.10.1 General .20
8.10.2 Purpose . 21
8.10.3 Procedure . 21
8.10.4 Measurement . 21
iii
ISO/DIS 8611-1:2023(E)
8.11 Test 11 — Top deck edge impact test . 22
8.11.1 Purpose . 22
8.11.2 Procedure .22
8.11.3 Measurement . 23
8.12 Test 12 — Block impact test .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.