EN ISO 5175-2:2017

Gas welding equipment - Safety devices - Part 2: Devices not incorporating a flame (flashback) arrestor (ISO 5175-2:2017, Corrected version 2019-01)

ISO 5175-2:2017 specifies the general requirements and tests for safety devices for fuel gases and oxygen or compressed air which do not incorporate a flame (flashback) arrestor used downstream of manifold, cylinder and/or pipeline outlet regulators, and upstream of blowpipes for welding, cutting and allied processes.
ISO 5175-2:2017 does not specify the location of these devices in the gas system.
ISO 5175-2:2017 in not applicable to safety devices which incorporate a flame arrestor, covered by ISO 5175‑1.

Gasschweißgeräte - Sicherheitseinrichtungen - Teil 2: Ohne integrierte Flammensperre (ISO 5175-2:2017)

Matériel de soudage au gaz - Dispositifs de sécurité - Partie 2: Dispositifs sans arrêt de flamme (ISO 5175-2:2017, Version corrigée 2019-01)

ISO 5175-2:2017 spécifie les exigences générales et les essais des dispositifs de sécurité pour les gaz combustibles et l'oxygène ou l'air comprimé, sans arrêt de flamme (retour de flamme), utilisés en aval des centrales de détente, des détendeurs pour bouteilles et (ou) canalisations, et en amont des chalumeaux pour le soudage, le coupage et les techniques connexes.
ISO 5175-2:2017 ne spécifie pas la position de ces dispositifs dans la distribution du gaz.
ISO 5175-2:2017 ne s'applique pas aux dispositifs de sécurité avec arrêt de flamme, couverts par l'ISO 5175‑1.

Oprema za plamensko varjenje - Varnostne naprave - 2. del: Naprave brez vgrajene varovalke proti povratnemu udaru (ISO 5175-2:2017)

Ta del evropskega standarda določa splošne zahteve in preskuse za varnostne naprave za gorivne pline in kisik ali stisnjeni zrak brez vgrajene varovalke proti povratnemu udaru v smeri stran od regulatorjev v razdelilnikih, cilindrih in/ali dovodih cevi ter v smeri proti gorilnikom za varjenje, rezanje in sorodne postopke. Ta standard ne določa položajev teh naprav v plinskem sistemu. Ta standard ne vključuje zahtev za varnostne naprave z vgrajeno varovalko proti povratnemu udaru, ki so zajete v standardu EN 730-1.

General Information

• Status: Published
• Publication Date: 28-Nov-2017
• Withdrawal Date: 30-May-2018
• ICS: 25.160.30 - Welding equipment
• Technical Committee: CEN/TC 121 - Welding
• Drafting Committee: CEN/TC 121/WG 19 - Equipment for gas welding, cutting and allied processes
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 29-Nov-2017
• Completion Date: 29-Nov-2017
• Ref Project: SIST EN ISO 5175-2:2018 - Gas welding equipment - Safety devices - Part 2: Not incorporating a flame (flashback) arrestor (ISO 5175-2:2017)

Relations

• Replaces: EN 730-2:2002 - Gas welding equipment - Safety devices - Part 2: Not incorporating a flame (flashback) arrestor
• Effective Date: 06-Dec-2017

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 5175-2:2018
01-februar-2018
1DGRPHãþD
SIST EN 730-2:2003
Oprema za plamensko varjenje - Varnostne naprave - 2. del: Naprave brez vgrajene
varovalke proti povratnemu udaru (ISO 5175-2:2017)
Gas welding equipment - Safety devices - Part 2: Not incorporating a flame (flashback)
arrestor (ISO 5175-2:2017)
Gasschweißgeräte - Sicherheitseinrichtungen - Teil 2: Ohne integrierte Flammensperre
(ISO 5175-2:2017)
Matériel de soudage au gaz - Dispositifs de sécurité - Partie 2: Sans arrêt de flamme
(ISO 5175-2:2017)
Ta slovenski standard je istoveten z: EN ISO 5175-2:2017
ICS:
25.160.30 Varilna oprema Welding equipment
SIST EN ISO 5175-2:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 5175-2:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 5175-2:2018


EN ISO 5175-2
EUROPEAN STANDARD

NORME EUROPÉENNE

November 2017
EUROPÄISCHE NORM
ICS 25.160.30 Supersedes EN 730-2:2002
English Version

Gas welding equipment - Safety devices - Part 2: Not
incorporating a flame (flashback) arrestor (ISO 5175-
2:2017)
Matériel de soudage au gaz - Dispositifs de sécurité - Gasschweißgeräte - Sicherheitseinrichtungen - Teil 2:
Partie 2: Sans arrêt de flamme (ISO 5175-2:2017) Ohne integrierte Flammensperre (ISO 5175-2:2017)
This European Standard was approved by CEN on 20 November 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5175-2:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 5175-2:2018
EN ISO 5175-2:2017 (E)
Contents Page
European foreword . 3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 5175-2:2018
EN ISO 5175-2:2017 (E)
European foreword
This document (EN ISO 5175-2:2017) has been prepared by Technical Committee ISO/TC 44 “Welding
and allied processes” in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2018, and conflicting national standards shall be
withdrawn at the latest by May 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 730-2:2002.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 5175-2:2017 has been approved by CEN as EN ISO 5175-2:2017 without any
modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 5175-2:2018

---------------------- Page: 6 ----------------------

SIST EN ISO 5175-2:2018
INTERNATIONAL ISO
STANDARD 5175-2
First edition
2017-09
Gas welding equipment — Safety
...