EN ISO 1089:2023

Resistance welding equipment - Electrode taper fits for spot welding equipment - Dimensions (ISO 1089:2023)

This document specifies the dimensions and tolerances of taper fits between the following:
—     straight electrodes and electrode holders;
—     electrode adapters connecting electrode caps and electrode holders;
—     female electrode caps and electrode adapters;
—     male electrode caps and electrode adapters.
NOTE            Electrode holders and electrode caps utilizing locking tapers are addressed in ISO 20168.

Widerstandsschweißeinrichtungen - Elektrodensitze für Punktschweißeinrichtungen - Maße (ISO 1089:2023)

Dieses Dokument legt Maße und zulässige Abweichungen von Kegelsitzen zwischen den folgenden Elementen fest:
   gerade Elektroden und Elektrodenhalter;
   Elektrodenschäfte, Elektrodenkappen und Elektrodenhalter;
   Elektrodenkappen mit Innenkegel und Elektrodenschäfte;
   Elektrodenkappen mit Außenkegel und Elektrodenschäfte.
ANMERKUNG   Elektrodenhalter und Elektrodenkappen, die selbsthemmende Kegel verwenden, werden in ISO 20168 behandelt.

Matériel de soudage par résistance - Emmanchements coniques d'électrodes pour machines à souder par points - Dimensions (ISO 1089:2023)

Le présent document spécifie les dimensions et tolérances des emmanchements coniques entre les éléments suivants:
—     des pointes d’électrodes droites et des porte-électrodes;
—     des allonges d’électrodes reliant des embouts amovibles et des porte-électrodes;
—     des embouts amovibles femelles et des allonges d’électrodes;
—     des embouts amovibles mâles et des allonges d’électrodes.
NOTE            Les porte-électrodes et les embouts amovibles utilisant des cônes de serrage sont couverts dans l’ISO 20168.

[Not translated]

General Information

• Status: Published
• Publication Date: 25-Jul-2023
• ICS: 25.160.30 - Welding equipment
• Technical Committee: CEN/TC 121 - Welding
• Drafting Committee: CEN/TC 121 - Welding
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 26-Jul-2023
• Completion Date: 26-Jul-2023
• Ref Project: oSIST EN ISO 1089 - Resistance welding equipment - Electrode taper fits for spot welding equipment - Dimensions (ISO 1089:2023)

Relations

• Replaces: EN 21089:1991 - Electrode taper fits for spot welding equipment - Dimensions (ISO 1089:1980)
• Effective Date: 28-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 1089:2023
01-november-2023
Nadomešča:
SIST EN 21089:1998
Oprema za uporovno varjenje - Nastavki elektrod pri opremi za točkovno varjenje -
Mere (ISO 1089:2023)
Resistance welding equipment - Electrode taper fits for spot welding equipment -
Dimensions (ISO 1089:2023)
Widerstandsschweißeinrichtungen - Elektrodensitze für Punktschweißeinrichtungen -
Maße (ISO 1089:2023)
Matériel de soudage par résistance - Emmanchements coniques d'électrodes pour
machines à souder par points - Dimensions (ISO 1089:2023)
Ta slovenski standard je istoveten z: EN ISO 1089:2023
ICS:
25.160.30 Varilna oprema Welding equipment
SIST EN ISO 1089:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

SIST EN ISO 1089:2023
SIST EN ISO 1089:2023
EN ISO 1089
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2023
EUROPÄISCHE NORM
ICS 25.160.30 Supersedes EN 21089:1991
English Version
Resistance welding equipment - Electrode taper fits for
spot welding equipment - Dimensions (ISO 1089:2023)
Matériel de soudage par résistance - Emmanchements Widerstandsschweißeinrichtungen - Elektrodensitze
coniques d'électrodes pour machines à souder par für Punktschweißeinrichtungen - Maße (ISO
points - Dimensions (ISO 1089:2023) 1089:2023)
This European Standard was approved by CEN on 23 June 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1089:2023 E
worldwide for CEN national Members.

SIST EN ISO 1089:2023
Contents Page
European foreword . 3

SIST EN ISO 1089:2023
European foreword
This document (EN ISO 1089:2023) has been prepared by Technical Committee ISO/TC 44 "Welding
and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2024, and conflicting national standards shall
be withdrawn at the latest by January 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 21089:1991.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 1089:2023 has been approved by CEN as EN ISO 1089:2023 without any modification.

SIST EN ISO 1089:2023
SIST EN ISO 1089:2023
INTERNATIONAL ISO
STANDARD 1089
Second edition
2023-07
Resistance welding equipment —
Electrode taper fits for spot welding
equipment — Dimensions
Matériel de soudage par résistance — Emmanchements coniques
d'électrodes pour machines à souder par points — Dimensions
Reference number
ISO 1089:2023(E)
SIST EN ISO 1089:2023
ISO 1089:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
SIST EN ISO 1089:2023
ISO 1089:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions .1
5 Designation . 6
6 Marking . . 6
Annex A (informative) Alternative types and dimensions of female and male electrode
taper fits . 7
Bibliography . 8
iii
SIST EN ISO 1089:2023
ISO 1089:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use
of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO had not received
notice of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all
such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards,
...