EN 845-2:2013/FprA1:2015
(Amendment)Specification for ancillary components for masonry - Part 2: Lintels
Specification for ancillary components for masonry - Part 2: Lintels
This European Standard specifies requirements for prefabricated lintels for maximum spans of 4,5 m and made from steel, autoclaved aerated concrete, manufactured stone, concrete, fired clay units, calcium silicate units, natural stone units, or a combination of these materials. Concrete and steel beams conforming to EN 1090-1, EN 12602 and EN 13225, as appropriate, are not covered by this standard. Prefabricated lintels can be either complete lintels or the prefabricated part of a composite lintel. This European Standard is not applicable to: a) lintels completely made on site; b) lintels of which the tensile parts are made on site; c) timber lintels; d) natural stone lintels, not reinforced. Linear components spanning clear openings greater than 4,5 m in masonry walls and linear components intended for use independently in a structural role (e.g. beams) are not covered by this standard.
Festlegungen für Ergänzungsbauteile für Mauerwerk - Teil 2: Stürze
Spécifications pour composants accessoires de maçonnerie - Partie 2: Linteaux
Specifikacija za dodatne komponente zidovja - 2. del: Preklade
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 845-2:2013/kFprA1:2015
01-december-2015
Specifikacija za dodatne komponente zidovja - 2. del: Preklade
Specification for ancillary components for masonry - Part 2: Lintels
Festlegungen für Ergänzungsbauteile für Mauerwerk - Teil 2: Stürze
Spécifications pour composants accessoires de maçonnerie - Partie 2: Linteaux
Ta slovenski standard je istoveten z: EN 845-2:2013/FprA1:2015
ICS:
91.060.10 Stene. Predelne stene. Walls. Partitions. Facades
Fasade
91.080.30 Zidane konstrukcije Masonry
SIST EN 845-2:2013/kFprA1:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 845-2:2013/kFprA1:2015
---------------------- Page: 2 ----------------------
SIST EN 845-2:2013/kFprA1:2015
FINAL DRAFT
EUROPEAN STANDARD
EN 845-2:2013
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
October 2015
ICS 91.080.30
English Version
Specification for ancillary components for masonry - Part
2: Lintels
Spécifications pour composants accessoires de Festlegungen für Ergänzungsbauteile für Mauerwerk -
maçonnerie - Partie 2: Linteaux Teil 2: Stürze
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical
Committee CEN/TC 125.
This draft amendment A1, if approved, will modify the European Standard EN 845-2:2013. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 845-2:2013/FprA1:2015:2015 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 845-2:2013/kFprA1:2015
EN 845-2:2013/FprA1:2015 (E)
Contents Page
European foreword . 3
1 Modification to Clause 8. 4
2 Modification to Annex ZA . 11
2
---------------------- Page: 4 ----------------------
SIST EN 845-2:2013/kFprA1:2015
EN 845-2:2013/FprA1:2015 (E)
European foreword
This document (EN 845-2:2013/FprA1:2015) has been prepared by Technical Committee CEN/TC 125
“Masonry”, the secretariat of which is held by BSI.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
3
---------------------- Page: 5 ----------------------
SIST EN 845-2:2013/kFprA1:2015
EN 845-2:2013/FprA1:2015 (E)
1 Modification to Clause 8
Delete Clause 8 entirely and replace it with the following:
8 Assessment and verification of constancy of performance - AVCP
"8.1 General
The compliance of lintels with the requirements of this standard and with the performances declared by
the manufacturer in the DoP shall be demonstrated by:
- determination of the product type;
- factory production control by the manufacturer, including product assessment.
The manufacturer shall always reta
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.