FprEN ISO 10256-2

Protective equipment for use in ice hockey - Part 2: Head protection for skaters (ISO/FDIS 10256-2:2024)

This document specifies performance requirements and test methods for head protectors for use in ice hockey.
This document is applicable to head protectors worn by ice hockey players excluding goalkeepers and by referees.

Schutzausrüstung zum Gebrauch beim Eishockey - Teil 2: Kopfschutz für Eisläufer (ISO/FDIS 10256-2:2024)

Dieses Dokument legt Leistungsanforderungen und Prüfverfahren für Kopfschützer zur Verwendung beim Eishockey fest.
Dieses Dokument gilt für Kopfschützer, die von Eishockeyspielern, mit Ausnahme von Torhütern, und von Schiedsrichtern getragen werden.

Équipements de protection destinés à être utilisés en hockey sur glace - Partie 2: Protections de tête pour les patineurs (ISO/FDIS 10256-2:2024)

Le présent document spécifie les exigences de performance et les méthodes d'essai applicables aux protections de tête destinées à être utilisées en hockey sur glace.
Le présent document s'applique aux protections de tête portées par les joueurs de hockey sur glace autres que les gardiens de but, et par les arbitres.

Varovalna oprema za uporabo pri hokeju na ledu - 2. del: Zaščita glave za drsalce (ISO/FDIS 10256-2:2024)

General Information

• Status: Not Published
• Publication Date: 15-Sep-2024
• ICS: 13.340.20 - Head protective equipment
• ICS: 97.220.20 - Winter sports equipment
• Technical Committee: CEN/TC 158 - Head protection
• Drafting Committee: CEN/TC 158 - Head protection
• Current Stage: 5060 - Closure of Vote - Formal Approval
• Start Date: 13-Jun-2024
• Completion Date: 13-Jun-2024
• Directive: 2016/425 - Regulation (EU) 2016/425 of the European Parliament and of the Council of 9 March 2016 on personal protective equipment and repealing Council Directive 89/686/EEC
• Mandate: M/571 - COMMISSION IMPLEMENTING DECISION of 19.11.2020 on a standardisation request to the European Committee for Standardization and the European Committee for Electrotechnical Standardization as regards personal protective equipment in support of Regulation (EU) 2016/425 of the European Parliament and of the Council
• Ref Project: kSIST FprEN ISO 10256-2:2024 - Protective equipment for use in ice hockey - Part 2: Head protection for skaters (ISO/FDIS 10256-2:2024)

Relations

• Revises: EN ISO 10256-2:2018 - Protective equipment for use in ice hockey - Part 2: Head protection for skaters (ISO 10256-2:2016)
• Effective Date: 18-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO 10256-2:2022
01-januar-2022
Varovalna oprema za uporabo pri hokeju na ledu - 2. del: Zaščita glave za drsalce
(ISO/DIS 10256-2:2021)
Protective equipment for use in ice hockey - Part 2: Head protection for skaters (ISO/DIS
10256-2:2021)
Schutzausrüstung zum Gebrauch beim Eishockey - Teil 2: Kopfschutz für Eisläufer
(ISO/DIS 10256-2:2021)
Équipements de protection destinés à être utilisés en hockey sur glace - Partie 2:
Protections de tête pour les patineurs (ISO/DIS 10256-2:2021)
Ta slovenski standard je istoveten z: prEN ISO 10256-2
ICS:
13.340.20 Varovalna oprema za glavo Head protective equipment
97.220.20 Oprema za zimske športe Winter sports equipment
oSIST prEN ISO 10256-2:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

oSIST prEN ISO 10256-2:2022
oSIST prEN ISO 10256-2:2022
DRAFT INTERNATIONAL STANDARD
ISO/DIS 10256-2
ISO/TC 83/SC 5 Secretariat: SCC
Voting begins on: Voting terminates on:
2021-11-16 2022-02-08
Protective equipment for use in ice hockey —
Part 2:
Head protection for skaters
ICS: 97.220.20; 13.340.20
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 10256-2:2021(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2021

oSIST prEN ISO 10256-2:2022
ISO/DIS 10256-2:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
oSIST prEN ISO 10256-2:2022
ISO/DIS 10256-2:2021(E)
Contents Page
Foreword .iv
European foreword .v
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements . 3
4.1 Materials and construction . 3
4.2 Protected area . 3
4.2.1 General . 3
4.2.2 Ear aperture . 3
4.2.3 Ventilation . 3
4.3 Penetration (test blade) . 3
4.4 Field of vision . 4
4.5 Shock absorbing capacity . 4
4.6 Retention system . 4
4.6.1 Straps . 4
4.6.2 Extensibility and strength . 4
5 Test methods . 4
5.1 Tolerances . 4
5.2 Sampling . 4
5.3 Conditioning temperatures . 5
5.4 Placing and adjusting head protectors . . 5
5.5 Determination of protected area . 5
5.5.1 Test apparatus . 5
5.5.2 Procedure . 5
5.6 Penetration test . 5
5.6.1 Test apparatus . 5
5.6.2 Procedure . 5
5.7 Field of vision test method . 5
5.8 Shock absorbing test . 6
5.8.1 Impact sites . 6
5.8.2 Marking impact sites on headform . 6
5.8.3 Apparatus . 6
5.8.4 Impact Procedure . 7
5.9 Determination of retention system function. 7
5.9.1 Apparatus . 7
5.9.2 Placing and adjusting . 7
5.9.3 Extensibility and releasing force . 7
6 Test report . 8
7 Markings . 8
8 Information for users . 8
Annex A (normative) Impact test using a guided fall .16
ANNEX ZA (informative) Relationship between this European Standard and the essential
requirements of Regulation (EU) 2016/425 of the European Parliament and of the
Council of 9 March 2016 on personal protective equipment aimed to be covered .20
iii
oSIST prEN ISO 10256-2:2022
ISO/DIS 10256-2:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 83, Sports and other recreational facilities
and equipment, Subcommittee SC 5, Ice hockey equipment and facilities, in collaboration with the
European Committee for Standardization (CEN) Technical Committee CEN/TC 158, Head protection, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 10256-2:2016), which has been
technically revised.
The main changes compared to the previous edition are as follows:
— Definitions were reordered to reflect their location in the document and updated.
— Clauses 4.1, 4.4, 5.1 and 5.7 were updated.
— In Clause 4.4 a), the degree of the upward plane was changed from 35° to 25° to align with EN 13087-
6:2012.
— Apparatus was added to Clause 5.4 and the procedure updated.
— Clause 5.6 (field of vision) was modified to refer to EN 13087-6:2012.
— Clause 5.7.3 was updated to refer to a revised Annex A.
— Table 1 was revised to include additional tests.
— Annex A was expanded to include more information on the testing equipment and procedure.
...