EN ISO 19076:2016
(Main)Leather - Measurement of leather surface - Using electronic techniques (ISO 19076:2016)
Leather - Measurement of leather surface - Using electronic techniques (ISO 19076:2016)
ISO 19076:2016 provides a method for the measurement of the surface of leather or leather parts by the use of electronic measuring machines.
It applies to the measurement of leather (or leather parts) fulfilling the following requirements:
- flexible leather, finished or unfinished, dry or wet leather;
- flexibility: such to allow full distension on the measuring line/surface.
Leder - Messung der Oberfläche des Leders - Elektronische Verfahren (ISO 19076:2016)
Diese Internationale Norm legt eine Methode für die Messung der Oberfläche von Leder oder von Lederteilen durch die Anwendung elektronischer Messmaschinen fest.
Die Norm gilt für die Messung von Leder (oder Lederteilen), das (oder die) die folgenden Anforderungen erfüllt (erfüllen):
flexibles Leder, mit oder ohne Zurichtung, trockenes oder nasses Leder ;
Flexibilität: um die volle Ausdehnung auf der Messlinie/Oberfläche zu ermöglichen.
ANMERKUNG Die beteiligten Seiten stimmen sich bei gegerbtem und abgewelktem, nassem Leder über die Art der Konditionierung ab. Im Streitfall wird das Leder nach den Referenzstandardbedingungen in ISO 2419 konditioniert.
Cuir - Mesurage de la surface du cuir - Utilisation de techniques électroniques (ISO 19076:2016)
L'ISO 19076 :2016 fournit une méthode pour le mesurage de la surface du cuir ou de pièces de cuir au moyen d'appareils de mesure électroniques.
Elle s'applique au mesurage du cuir (ou de pièces de cuir) satisfaisant aux exigences suivantes:
- cuir souple, fini ou non fini, cuir humide ou sec;
- souplesse: cuir pouvant être complètement distendu sur la ligne/surface de mesurage.
Usnje - Merjenje usnjene površine - Uporaba elektronskih tehnik (ISO 19076:2016)
Ta mednarodni standard podaja metodo za merjenje površine usnja ali usnjenih
delov z uporabo elektronskih merilnih strojev.
Uporablja se za merjenje usnja (ali usnjenih delov), pri čemer izpolnjuje naslednje zahteve:
– upogljivo usnje, obdelano ali neobdelano, suho ali mokro usnje;
– upogljivost: takšna, ki omogoča popolno razteznost na merilni črti/površini.
OPOMBA: Pri ustrojenem in stiskanem mokrem usnju se sodelujoče stranke dogovorijo glede vrste kondicioniranja. V primeru
spora je treba usnje kondicionirati v skladu z referenčnimi pogoji standarda ISO 2419.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2016
Usnje - Merjenje usnjene površine - Uporaba elektronskih tehnik (ISO 19076:2016)
Leather - Measurement of leather surface - Using electronic techniques (ISO
19076:2016)
Leder - Messung der Oberfläche des Leders - Elektronische Verfahren (ISO 19076:2016)
Cuir - Mesurage de la surface du cuir - Utilisation de techniques électroniques (ISO
19076:2016)
Ta slovenski standard je istoveten z: EN ISO 19076:2016
ICS:
59.140.30 Usnje in krzno Leather and furs
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 19076
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2016
EUROPÄISCHE NORM
ICS 59.140.30
English Version
Leather - Measurement of leather surface - Using
electronic techniques (ISO 19076:2016)
Cuir - Mesurage de la surface du cuir - Utilisation de Leder - Messung der Oberfläche des Leders -
techniques électroniques (ISO 19076:2016) Elektronische Verfahren (ISO 19076:2016)
This European Standard was approved by CEN on 30 July 2016.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19076:2016 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 19076:2016) has been prepared by Technical Committee IULTCS “International
Union of Leather Technologists and Chemists Societies” in collaboration with Technical Committee
CEN/TC 289 “Leather” the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2017, and conflicting national standards
shall be withdrawn at the latest by February 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 19076:2016 has been approved by CEN as EN ISO 19076:2016 without any modification.
INTERNATIONAL ISO
STANDARD 19076
IULTCS/IUP 58
First edition
2016-08-15
Leather — Measurement of leather
surface — Using electronic techniques
Cuir — Mesurage de la surface du cuir — Utilisation de techniques
électroniques
Reference numbers
ISO 19076:2016(E)
IULTCS/IUP 58:2016(E)
©
ISO 2016
ISO 19076:2016(E)
IULTCS/IUP 58:2016(E)
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
ISO 19076:2016(E)
IULTCS/IUP 58:2016(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus and materials. 1
5.1 Measuring machine . 1
5.1.1 Machine design types . 1
5.1.2 Type A, B, and C measuring machines . 2
5.1.3 Type D measuring machine . 2
5.2 Reference calibrated templates for machine verification . 3
6 Sampling and conditioning . 3
7 General measurement criteria. 3
7.1 General requirement . 3
7.2 Leather orientation during measurement . 4
7.2.1 General. 4
7.2.2 Measuring whole leathers . 4
7.2.3 Measuring half leathers . 4
7.2.4 Measuring leather cut pieces . 4
7.3 Measurement operations . 4
7.3.1 Roller machines . 4
7.3.2 Conveyor machines . 4
7.3.3 Flatbed scanner machines and bi-dimensional static measuring devices . 5
8 Measurement procedure . 5
9 Calculation and expression of results . 6
10 Test report . 6
Annex A (normative) Calibrated templates for the verification of electronic measuring machines .7
Annex B (normative) Procedure for the verification of a measuring machine by
calibrated templates . 9
Annex C (normative) Laboratory record of calibrated templates .11
Annex D (informative) Repeatability and reproducibility .12
Bibliography .14
ISO 19076:2016(E)
IULTCS/IUP 58:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
ISO 19076/IUP 58 was prepared by the Physical Test Commission of the International Union of Leather
Technologists and Chemists Societies (IUP Commission, IULTCS) in collaboration with the European
Committee for Standardization (CEN) Technical Committee CEN/TC 289, Leather, the secretariat of
which is held by UNI, in accordance with the agreement on technical co-operation between ISO and CEN
(Vienna Agreement).
IULTCS, originally formed in 1897, is a world-wide organization of professional leather societies to
further the advancement of leather science and technology. IULTCS has three Commissions, which
are responsible for establishing international methods for the sampling and testing of leather. ISO
recognizes IULTCS as an international standardizing body for the preparation of test methods for
leather.
iv © ISO 2016 – All rights reserved
ISO 19076:2016(E)
IULTCS/IUP 58:2016(E)
Introduction
Leather surface measuring equipment used within the European Union (EU)
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.