EN ISO 9100-9:2005

Glass containers - Vacuum lug finishes - Part 9: 63, 66 and 70 deep (ISO 9100-9:2005)

ISO 9100-9:2005 specifies the dimensions of vacuum lug finishes with nominal sizes of 63, 66 and 70 mm deep for wide-mouth glass containers.

Glasbehälter - Vakuum-Nockenverschluss-Mündungen - Teil 9: 63, 66 und 70 deep (ISO 9100-9:2005)

Récipients en verre - Bagues à crans pour bouchage sous vide - Partie 9: 63, 66 et 70 deep (ISO 9100-9:2005)

L'ISO 9100-9:2005 spécifie les dimensions des bagues à crans pour bouchage sous vide de cote nominale 63 mm, 66 mm et 70 mm deep, destinées aux récipients en verre à col large.

Steklena embalaža – Grla za vakuumsko zapiranje - 9. del: 63, 66 in 70, globoko (ISO 9100-9:2005)

General Information

• Status: Published
• Publication Date: 14-Jan-2005
• ICS: 55.100 - Bottles. Pots. Jars
• Technical Committee: CEN/TC 261 - Packaging
• Drafting Committee: CEN/TC 261/SC 5/WG 21 - Glass packaging
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Start Date: 23-Oct-2009
• Completion Date: 23-Oct-2009
• Directive: 80/232/EEC - Ranges of nominal quantities and nominal capacities permitted for certain pre-packaged products
• Directive: 87/356/EEC - Ranges of nominal quantities and nominal capacities permitted for certain pre-packged products (Dir. 80/232/EEC amendment)
• Ref Project: SIST EN ISO 9100-9:2005 - Glass containers - Vacuum lug finishes - Part 9: 63, 66 and 70 deep (ISO 9100-9:2005)

Overview

EN ISO 9100-9:2005 - Glass containers - Vacuum lug finishes - Part 9: 63, 66 and 70 deep (ISO 9100-9:2005) is a CEN-adopted ISO standard that defines the dimensional requirements for vacuum lug finishes on wide-mouth glass containers with nominal depths of 63, 66 and 70 mm. Published January 2005 (approved September 2004), the standard establishes cutter profiles, thread construction and tolerances to ensure compatibility between glass containers and vacuum closure systems.

Key topics and requirements

• Scope: Dimensions for vacuum lug finishes for wide-mouth containers (nominal depths 63, 66, 70 mm).
• Dimensional details: Clause 3 and Table 1 specify the finish geometry, cutter profile, thread parameters and permitted tolerances.
• Thread parameters: The standard specifies thread pitch and form for proper cap engagement (example: pitch shown as 1½ TPI in the table).
• Cutter profile and leads: Cutter inclination (α) is controlled and leads correspond to the cut-in profile; cutter leads of 4 mm are indicated in the document’s data table.
• Sealing surface quality: The sealing surface must be free of checks, dips, crizzles and other defects that could affect vacuum performance.
• Ovality and concentricity: Ovality of finish diameters should be minimized; diameters identified (E and T) should be concentric for reliable sealing and cap removal.
• Cap removal / cam-off point: The theoretical cam-off point is required to lie on the upper flank of the thread to assist cap removal.
• Design flexibility: Details not specified by the standard may be selected according to application; general tolerances reference EN 22768-1.

Practical applications

• Glass container manufacturers use this standard to design moulds and finish tooling for vacuum lug finishes so that containers accept industry-standard vacuum caps.
• Closure and cap designers rely on the defined thread and sealing geometries to produce compatible vacuum closures.
• Packaging engineers and bottlers use it to ensure reliable vacuum sealing for products such as wide-mouth jars, preserves and other vacuum-packaged foods.
• Quality inspectors and test labs refer to the dimensions and tolerance limits when verifying finish conformity and sealing performance.
• Mould makers and tooling suppliers apply the cutter profile and lead specifications when preparing finishing tooling.

Related standards

• EN 22768-1 (General tolerances for linear and angular dimensions) is cited for default tolerance practice.
• The document is based on CETIE data (GME 20-07:1995) and aligns with ISO/TC 63 glass container work.

Keywords: EN ISO 9100-9:2005, glass container vacuum lug finishes, 63 mm 66 mm 70 mm finishes, wide-mouth glass containers, vacuum closure thread, cutter profile, packaging standards.

Standards Content (Sample)

SLOVENSKI STANDARD
01-marec-2005
Steklena embalaža – Grla za vakuumsko zapiranje - 9. del: 63, 66 in 70, globoko
(ISO 9100-9:2005)
Glass containers - Vacuum lug finishes - Part 9: 63, 66 and 70 deep (ISO 9100-9:2005)
Glasbehälter - Vakuum-Nockenverschluss-Mündungen - Teil 9: 63, 66 und 70 deep (ISO
9100-9:2005)
Récipients en verre - Bagues a crans pour bouchage sous vide - Partie 9: 63, 66 et 70
deep (ISO 9100-9:2005)
Ta slovenski standard je istoveten z: EN ISO 9100-9:2005
ICS:
55.100 Steklenice. Lonci. Kozarci Bottles. Pots. Jars
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 9100-9
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2005
ICS 55.100
English version
Glass containers - Vacuum lug finishes - Part 9: 63, 66 and 70
deep (ISO 9100-9:2005)
Récipients en verre - Bagues à crans pour bouchage sous Glasbehälter - Vakuum-Nockenverschluss-Mündungen -
vide - Partie 9: 63, 66 et 70 deep (ISO 9100-9:2005) Teil 9: 63, 66 und 70 deep (ISO 9100-9:2005)
This European Standard was approved by CEN on 23 September 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9100-9:2005: E
worldwide for CEN national Members.

Contents
Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Dimensions.4
Bibliography .8

Foreword
This document (EN ISO 9100-9:2005) has been prepared by Technical Committee CEN/TC 261 “Packaging”,
the secretariat of which is held by AFNOR, in collaboration with Technical Committee ISO/TC 63 “Glass
containers”.
This European Standard sh
...