EN 10341:2006

Cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state

This document specifies cold-rolled electrical non-oriented non-alloy ) or alloy ) steel sheet and strip delivered in nominal thicknesses of 0,50 mm and 0,65 mm in the semi-processed condition, that is without final heat treatment; in particular, it specifies general requirements, magnetic properties, geometric characteristics and tolerances and technological characteristics, as well as the inspection procedure.
This document applies to material intended for the construction of magnetic circuits.
These magnetic materials correspond respectively to subclauses C21 and B2 of IEC 60404-1:2000.

Kaltgewalztes Elektroblech und -band aus unlegierten und legierten Stählen im nicht schlussgeglühten Zustand

Dieses Dokument gilt für kaltgewalztes nicht kornorientiertes Elektroblech und -band aus unlegierten 1) und
legierten 2) Stählen, geliefert in Nenndicken von 0,50 mm und 0,65 mm im nicht schlussgeglühten Zustand,
d. h. ohne abschließende Wärmebehandlung. Festgelegt sind die allgemeinen Anforderungen, die
magnetischen Eigenschaften, die geometrischen Eigenschaften und Toleranzen, die technologischen
Eigenschaften sowie die Prüfbedingungen.
Dieses Dokument gilt für Erzeugnisse, die für den Bau magnetischer Kreise bestimmt sind.
Diese magnetischen Werkstoffe entsprechen den Angaben in IEC 60404-1:2000, B.2 und C.21.

Bandes et tôles magnétiques laminées à froid en acier non allié et en acier allié livrées à l'état semi-fini

Le présent document spécifie les tôles et bandes magnétiques en acier non allié 1) et en acier allié 2) , à grains
non orientés, laminées à froid, livrées à l'état semi-fini, c'est-à-dire sans traitement thermique final, en
épaisseurs nominales de 0,50 mm et 0,65 mm ; en particulier, il spécifie les prescriptions générales, les
caractéristiques magnétiques, les caractéristiques géométriques et les tolérances, et les caractéristiques
technologiques ainsi que les modalités de contrôle.
Le présent document s’applique aux matériaux destinés à la construction de circuits magnétiques.
Ces matériaux magnétiques correspondent respectivement aux articles C21 et B2 de la CEI 60404-1:2000.

Hladno valjana elektropločevina in trakovi iz nelegiranega in legiranega jekla, dobavljena v nežarjenem končnem stanju

General Information

• Status: Published
• Publication Date: 30-May-2006
• Withdrawal Date: 29-Nov-2006
• ICS: 77.140.50 - Flat steel products and semi-products
• Technical Committee: ECISS/TC 108 - Steel sheet and strip for electrical applications
• Drafting Committee: ECISS/TC 108 - Steel sheet and strip for electrical applications
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 05-Mar-2018
• Ref Project: SIST EN 10341:2006 - Cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state

Relations

• Replaces: EN 10165:1995 - Cold rolled electrical alloyed steel sheet and strip delivered in the semi-processed state
• Effective Date: 22-Dec-2008
• Replaces: EN 10126:1995 - Cold rolled electrical non-alloyed steel sheet and strip delivered in the semi-processed state
• Effective Date: 22-Dec-2008

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed stateBandes et tôles magnétiques laminées a froid en acier non allié et en acier allié livrées a l'état semi-finiKaltgewalztes Elektroblech und -band aus unlegierten und legierten Stählen im nicht schlussgeglühten ZustandTa slovenski standard je istoveten z:EN 10341:2006SIST EN 10341:2006en77.140.50ICS:SIST EN 10165:1997SIST EN 10126:19971DGRPHãþDSLOVENSKI
STANDARDSIST EN 10341:200601-september-2006

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10341May 2006ICS 77.140.50Supersedes EN 10126:1995, EN 10165:1995
English VersionCold rolled electrical non-alloy and alloy steel sheet and stripdelivered in the semi-processed stateBandes et tôles magnétiques laminées à froid en acier nonallié et en acier allié livrées à l'état semi-finiKaltgewalztes Elektroblech und -band aus unlegierten undlegierten Stählen im nicht schlussgeglühten ZustandThis European Standard was approved by CEN on 20 April 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10341:2006: E

Foreword.3 Introduction.4 1 Scope.5 2 Normative references.5 3 Terms and definitions.5 4 Classification and designation.6 4.1 Classification.6 4.2 Designation.6 5 Information to be supplied by the purchaser.7 5.1 Mandatory information.7 5.2 Options.7 6 General requirements.8 6.1 Production process.8 6.2 Form of supply.8 6.3 Delivery condition.8 6.4 Surface condition.8 6.5 Suitability for cutting.9 7 Technical requirements.9 7.1 Magnetic properties.9 7.2 Geometrical characteristics and tolerances.11 7.3 Other properties.12 8 Inspection and testing.13 8.1 General.13 8.2 Sampling.13 8.3 Preparation of test specimens.13 8.4 Test methods.14 8.5 Retests.14 9 Marking, labelling and packing.15 10 Complaints.15 Annex A (informative)
Maximum specific total loss at 1,0 T.16 Annex B (informative)
Density determination.17 Bibliography.18

According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EN 10126:1995. As the final annealing of cold-rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state is the responsibility of the purchaser, attention is drawn to the importance of this treatment for the properties of the material. For this reason the magnetic properties in Table 1 are given for a reference condition (see 7.1.1) obtained by a suitable heat treatment. To ensure that the properties in use are equivalent to those specified, it is important that the heat treatment carried out by the user is equivalent to that used to define the reference condition. It is recognized that these materials may be used in the semi-processed state, in which case the magnetic properties are not subject to the specifications of this standard.

1) Non-alloy steel is that steel the basic constituent of which is iron containing alloying elements in amounts smaller
than the limiting values fixed by EN 10020. 2) Alloy steel is that steel the basic constituent of which is iron containing alloying elements in amounts equal to or
greater than the limiting values fixed by EN 10020.

3.4 internal stresses stresses which are characterized by a deviation in relation to the line of cutting 4 Classification and designation
4.1 Classification The steel grades covered by this document are classified according to the specified value of maximum specific total loss in watts per kilogram at 1,5 T after a reference heat treatment (see 7.1.1) and according to the nominal thickness of the material (0,50 mm, 0,65 mm). 4.2 Designation 4.2.1 For the steel grades covered by this document, the steel names are allocated in accordance with EN 10027-1. The steel numbers are allocated in accordance with EN 10027-2. The steel name comprises the following in the order given: 1) the letter M for electrical steel; 2) one hundred times the specified value of maximum specific total loss at 50 Hz, in watts per kilogram, corresponding to the nominal product thickness, at 1,5 T; 3) one hundred times the nominal thickness of the material, in millimetres; 4) the letter K for non-alloy or alloy electrical steel sheet or strip delivered in the semi-processed state. EXAMPLE M660-50K for electrical non-alloy or alloy steel sheet or strip with a specified maximum specific total loss at 1,5 T of 6,60 W/kg at 50 Hz and a nominal thickness of 0,50 mm, supplied in a semi-processed state.
...