EN 4539-2:2019
(Main)Aerospace series - Bearing, spherical, plain, in corrosion resisting steel with self-lubricating liner - Elevated load under low oscillations - Wide series - Dimensions and loads - Part 2: Inch series
Aerospace series - Bearing, spherical, plain, in corrosion resisting steel with self-lubricating liner - Elevated load under low oscillations - Wide series - Dimensions and loads - Part 2: Inch series
This European standard specifies the characteristics of spherical plain bearing in corrosion resistant steel, with self-lubricating liner, wide series, elevated load under low oscillations applications.
They shall be used in the temperature range −55 °C to 163 °C.
Luft- und Raumfahrt - Gelenklager aus korrosionsbeständigem Stahl mit selbstschmierender Beschichtung - Hohe Belastung, gering oszillierend - Breite Reihe - Maße und Belastungen - Teil 2: Inch-Reihe
Diese Europäische Norm legt die allgemeinen Eigenschaften von Gelenklagern aus korrosionsbeständigem Stahl mit selbstschmierender Beschichtung, breite Serie, für Anwendungen mit hoher Belastung bei geringer Drehbewegung, fest.
Sie müssen im Temperaturbereich von -55 °C bis 163 °C verwendet werden.
Série aérospatiale - Rotules lisses, en acier résistant à la corrosion à garniture autolubrifiante - À charge élevée sous faibles oscillations - Série large - Dimensions et charges - Partie 2 : Série en inches
La présente norme européenne spécifie les caractéristiques des rotules lisses en acier résistant à la corrosion à garniture autolubrifiante, série large, pour les applications à charge élevée sous faibles oscillations.
Les températures d’utilisation doivent être comprises entre -55 °C et 163 °C.
Aeronavtika - Kroglasti drsni ležaji iz korozijsko odpornega jekla s samomazalno oblogo - Z zvišano obremenitvijo pri nizkih oscilacijah - Široka serija - Mere in obremenitve - Palčne mere
Ta dokument določa značilnosti kroglastega drsnega ležaja iz korozijsko odpornega jekla s samomazalno oblogo, široke serije in z zvišano obremenitvijo pri nizkih nihanjih. Uporabljati jih je treba v temperaturnem razponu od –55 °C do 163 °C.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 4539-2:2020
01-januar-2020
Aeronavtika - Kroglasti drsni ležaji iz korozijsko odpornega jekla s samomazalno
oblogo - Z zvišano obremenitvijo pri nizkih oscilacijah - Široka serija - Mere in
obremenitve - Palčne mere
Aerospace series - Bearings, spherical plain, in corrosion resisting steel with self-
lubricating liner - Elevated load under low oscillations -Wide series - Dimensions and
loads - Inch series
Luft- und Raumfahrt - Gelenklager aus korrosionsbeständigem Stahl mit
selbstschmierender Beschichtung, hohe Belastung bei geringer Drehbewegung, breite
Reihe - Maße und Belastungen; Teil 2: Inch Reihe
Série aérospatiale - Rotules, en acier résistant à la corrosion à garniture autolubrifiante -
à charge élevée sous faibles oscillations - Série large - Dimensions et charges - Partie 2
: Série en inches
Ta slovenski standard je istoveten z: EN 4539-2:2019
ICS:
21.100.10 Drsni ležaji Plain bearings
49.035 Sestavni deli za letalsko in Components for aerospace
vesoljsko gradnjo construction
SIST EN 4539-2:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 4539-2:2020
---------------------- Page: 2 ----------------------
SIST EN 4539-2:2020
EN 4539-2
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2019
EUROPÄISCHE NORM
ICS 49.035
English Version
Aerospace series - Bearing, spherical, plain, in corrosion
resisting steel with self-lubricating liner - Elevated load
under low oscillations - Wide series - Dimensions and
loads - Part 2: Inch series
Série aérospatiale - Rotules lisses, en acier résistant à Luft- und Raumfahrt - Gelenklager aus
la corrosion à garniture autolubrifiante - À charge korrosionsbeständigem Stahl mit selbstschmierender
élevée sous faibles oscillations - Série large - Beschichtung - Hohe Belastung, gering oszillierend -
Dimensions et charges - Partie 2 : Série en inches Breite Reihe - Maße und Belastungen - Teil 2: Inch-
Reihe
This European Standard was approved by CEN on 2 December 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4539-2:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 4539-2:2020
EN 4539-2:2019 (E)
Contents
Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Symbols and definitions . 4
4 Required characteristics . 5
5 Designation. 9
6 Marking . 9
7 Technical specification . 9
8 Quality man
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.