Metallic materials - Vickers hardness test - Part 1: Test method (ISO 6507-1:2005)

ISO 6507-1:2005 specifies the Vickers hardness test method for the three different ranges of test force for metallic materials.
The Vickers hardness test is specified in ISO 6507-1:2005 for lengths of indentation diagonals between 0,020 mm and 1,400 mm.

Metallische Werkstoffe - Härteprüfung nach Vickers - Teil 1: Prüfverfahren (ISO 6507-1:2005)

In diesem Teil von IS0 6507 ist das Verfahren für die Härteprüfung nach Vickers für metallische Werkstoffe festgelegt. Die Härteprüfung nach Vickers ist in Abhängigkeit von der angewendeten Prüfkraft in drei Bereiche eingeteilt (siehe Tabelle 1).
Tabelle 1 — Bereiche der Prüfkraft
Bereiche der Prüfkraft, FN   Härtesymbol   Bezeichnung
F ³ 49,03   ³ HV 5   Vickers-Härteprüfung
1,961 £ F < 49,03   HV 0,2 bis < HV 5   Vickers-Kleinkrafthärteprüfung
0,098 07 £ F < 1,961   HV 0,01 bis < HV 0,2   Vickers-Mikrohärteprüfung
Die Härteprüfung nach Vickers ist in diesem Teil von ISO 6507 für Eindruckdiagonalenlängen zwischen
0,020 mm und 1,400 mm festgelegt.
ANMERKUNG 1   Für Eindruckdiagonalen kleiner als 0,020 mm muss beachtet werden, dass die Messunsicherheit größer wird.
ANMERKUNG 2   Im Allgemeinen nimmt die Streuung der Ergebnisse mit abnehmender Länge bei diagonaler bzw. abnehmender Prüfkraft zu. Dies gilt besonders für die Härteprüfung im Kleinkraft- und im Mikrobereich, wo die genaue Messung der Eindruckdiagonalen eingeschränkter ist. Bei Mikrohärteprüfungen ist die Genauigkeit der Messung der mittleren Eindruckdiagonalenlänge häufig nicht besser als ± 0,001 mm siehe Literaturhinweise [2] bis [5].
Für besondere Werkstoffe und/oder Erzeugnisse gibt es spezielle Internationale Normen.

Matériaux métalliques - Essai de dureté Vickers - Partie 1: Méthode d'essai (ISO 6507-1:2005)

L'ISO 6507-1:2005 spécifie la méthode d'essai de dureté Vickers pour les trois domaines différents de force d'essai, pour les matériaux métalliques.
L'essai de dureté Vickers est spécifié dans l'ISO 6507-1:2005 pour des longueurs de diagonales d'empreinte comprises entre 0,020 mm et 1,400 mm.

Kovinski materiali – Preskus trdote po Vickersu – 1. del: Preskusni postopek (ISO 6507-1:2005)

General Information

Status
Withdrawn
Publication Date
14-Dec-2005
Withdrawal Date
06-Mar-2018
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
07-Mar-2018

Relations

Buy Standard

Standard
EN ISO 6507-1:2006
English language
26 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-marec-2006
1DGRPHãþD
SIST EN ISO 6507-1:1998
Kovinski materiali – Preskus trdote po Vickersu – 1. del: Preskusni postopek (ISO
6507-1:2005)
Metallic materials - Vickers hardness test - Part 1: Test method (ISO 6507-1:2005)
Metallische Werkstoffe - Härteprüfung nach Vickers - Teil 1: Prüfverfahren (ISO 6507-
1:2005)
Matériaux métalliques - Essai de dureté Vickers - Partie 1: Méthode d'essai (ISO 6507-
1:2005)
Ta slovenski standard je istoveten z: EN ISO 6507-1:2005
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 6507-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2005
ICS 77.040.10 Supersedes EN ISO 6507-1:1997
English Version
Metallic materials - Vickers hardness test - Part 1: Test method
(ISO 6507-1:2005)
Matériaux métalliques - Essai de dureté Vickers - Partie 1: Metallische Werkstoffe - Härteprüfung nach Vickers - Teil
Méthode d'essai (ISO 6507-1:2005) 1: Prüfverfahren (ISO 6507-1:2005)
This European Standard was approved by CEN on 14 December 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6507-1:2005: E
worldwide for CEN national Members.

Foreword
This document (EN ISO 6507-1:2005) has been prepared by Technical Committee ISO/TC 164
"Mechanical testing of metals" in collaboration with Technical Committee ECISS/TC 1 "Steel -
Mechanical testing", the secretariat of which is held by AFNOR.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by June 2006, and conflicting national
standards shall be withdrawn at the latest by June 2006.

This document supersedes EN ISO 6507-1:1997.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Endorsement notice
The text of ISO 6507-1:2005 has been approved by CEN as EN ISO 6507-1:2005 without any
modifications.
INTERNATIONAL ISO
STANDARD 6507-1
Third edition
2005-12-15
Metallic materials — Vickers hardness
test —
Part 1:
Test method
Matériaux métalliques — Essai de dureté Vickers —
Partie 1: Méthode d'essai
Reference number
ISO 6507-1:2005(E)
©
ISO 2005
ISO 6507-1:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2005 – All rights reserved

ISO 6507-1:2005(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Principle. 2
4 Symbols and abbreviated terms . 2
5 Testing machine. 3
6 Test piece . 3
7 Procedure . 3
8 Uncertainty of the results . 5
9 Test report . 5
Annex A (normative) Minimum thickness of the test piece in relation to the test force and to the
hardness . 6
Annex B (normative) Tables of correction factors for use in tests made on curved surfaces . 8
Annex C (informative) Procedure for periodic checking of the testing machine by the user . 12
Annex D (informative) Uncertainty of the measured hardness values . 13
Bibliography . 19

ISO 6507-1:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 6507-1 was prepared by Technical Committee ISO/TC 164, Mechanical testing of metals, Subcommittee
SC 3, Hardness testing.
This third edition, together with ISO 6507-4, cancels and replaces the second edition (ISO 6507-1:1997) which
has been technically revised.
ISO 6507 consists of the following parts, under the general title Metallic materials — Vickers hardness test:
⎯ Part 1: Test method
⎯ Part 2: Verification and calibration of testing machines
⎯ Part 3: Calibration of reference blocks
⎯ Part 4: Tables of hardness values

iv © ISO 2005 – All rights reserved

ISO 6507-1:2005(E)
Introduction
The periodic checking of the testing machine described in informative Annex C is good metrological practice.
It is intended to make the annex normative in the next revision of this part of ISO 6507 Standard.
For automated measuring systems this standard should be applied accordingly.

INTERNATIONAL STANDARD ISO 6507-1:2005(E)

Metallic materials — Vickers hardness test —
Part 1:
Test method
1 Scope
This part of ISO 6507 specifies the Vickers hardness test method, for the three different ranges of test force
for metallic materials (see Table 1).
Table 1 — Ranges of test force
Ranges of test force, F
Hardness symbol Designation
N
F W 49,03 W HV 5
Vickers hardness test
1,961 u F < 49,03
HV 0,2 to < HV 5 Low-force Vickers hardness test
0,098 07 u F < 1,961
HV 0,01 to < HV 0,2 Vickers microhardness test

The Vickers hardness test is specified in this part of ISO 6507 for lengths of indentation diagonals between
0,020 mm and 1,400 mm.
NOTE 1 For indentation diagonals less than 0,020 mm, the increase of the uncertainty has to be considered.
NOTE 2 In general, decreasing the test force increases the scatter of results of the measurements. This is particularly
true for low-force Vickers hardness tests and Vickers microhardness tests, where the principal limitation will arise in the
measurement of the diagonals of the indentation. For Vickers microhardness, the accuracy of determination of the mean
diagonal length is unlikely to be better than ± 0,001 mm (see Bibliography [2]-[5]).
For specific materials and/or products, particular International Standards exist.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 6507-2:2005, Metallic materials — Vickers hardness test — Part 2: Verification and calibration of testing
machines
ISO 6507-4, Metallic materials — Vickers hardness test — Part 4: Tables of hardness values
ISO 6507-1:2005(E)
3 Principle
A diamond indenter, in the form of a right pyramid with a square base and with a specified angle between
opposite faces at the vertex, is forced into the surface of a test piece followed by measurement of the diagonal
length of the indentation left in the surface after removal of the test force, F (see Figure 1).

Figure 1 — Principle of the test
The Vickers hardness is proportional to the quotient obtained by dividing the test force by the sloping area of
the indentation, which is assumed to be a right pyramid with a square base, and having at the vertex the same
angle as the indenter.
4 Symbols and abbreviated terms
4.1 See Table 2 and Figure 1.
Table 2 — Symbols and abbreviated terms
Symbol/
Abbreviated Designation
term
α Angle between the opposite faces at the vertex of the pyramidal indenter (136°)
F
Test force, in newtons (N)
d Arithmetic mean, in millimetres, of the two diagonal lengths d and d (see Figure 1)
1 2
136°
2sF in
Test force F
HV
Vickers hardness=×Constant = 0,102 ≈ 0,189 1
Surface area of indentation
dd
NOTE Constant = 0,102 ≈ 1/9,806 65, where 9,806 65 is the conversion factor from kgf to N.
2 © ISO 2005 – All rights reserved

ISO 6507-1:2005(E)
4.2 The following is an example of the designation of Vickers hardness HV.
EXAMPLE
5 Testing machine
5.1 Testing machine, capable of applying a predetermined force or forces within the required range of test
forces, in accordance with ISO 6507-2.
5.2 Indenter, a diamond in the shape of a right pyramid with a square base, as specified in ISO 6507-2.
5.3 Measuring system, as specified in ISO 6507-2.
NOTE A suggested procedure for periodic checks of the hardness testing machine by the users is given in Annex C.
6 Test piece
6.1 The test shall be carried out on a surface which is smooth and even, free from oxide scale, foreign
matter and, in particular, completely free from lubricants, unless otherwise specified in product standards. The
finish of the surface shall permit accurate determination of the diagonal length of the indentation.
6.2 Preparation shall be carried out in such a way that any alteration of the surface hardness, due to
excessive heating or cold-working, for example, is minimized.
Due to the small depth of Vickers microhardness indentations, it is essential that special pr
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.