Textiles and textile products - Part 3: Safety of children's clothing - Security of attachment of metal mechanically applied press fasteners - Test method

This document defines a test method for security of attachment of functional and decorative metal mechanically applied press fasteners to children's clothing including for example gloves, hats, scarves, hosiery, ties, and textile belts.
IMPORTANT: Eyelets and rivets cannot be tested by this method as the integrity of the component when attached to textile fabrics is destroyed in the gripping action. Eyelets and rivets are assessed as described in CEN/TS 17394 4:2021.
This document does not apply to:
a)   child care articles;
b)   shoes, boots and similar footwear;
c)   toys (see NOTE 2);
d)   other articles sold with clothing.
NOTE 1   The above items are covered by other CEN Technical Committees and as such are out of the scope of this document.
NOTE 2   Disguise costumes including carnival costumes are examples of clothing which are also toys and fall within the scope of the Toy Safety Directive.
The scope of this document is limited to metal mechanically applied components. Work is in progress to develop standards for other garment components.
- EN 17394 2:2020, Textiles and textile products - Part 2: Safety of children's clothing - Security of attachment of buttons - Test method
- CEN/TS 17394 4:2021, Textiles and textile products - Part 4: Safety of children's clothing - Security of attachment of components except buttons and metal mechanically applied press fasteners - Test method
Performance requirements are provided in CEN/TS 17394 1:2021.

Textilien und textile Produkte - Teil 3: Sicherheit von Kinderbekleidung - Sicherheit der Befestigung von mechanisch befestigten Druckknöpfen - Prüfverfahren

Dieses Dokument legt ein Prüfverfahren für die Sicherheit der Befestigung von funktionellen und dekorativen mechanisch angebrachten Metalldruckverschlüssen an Kinderbekleidung fest, einschließlich z. B. Handschuhen, Mützen und Hüten, Schals, Strümpfen, Krawatten und Stoffgürteln.
WICHTIG — Ösen und Nieten können mit diesem Verfahren nicht geprüft werden, da die Komponente, wenn sie an textilem Material befestigt ist, durch den Klemm¬vorgang zerstört wird. Ösen und Nieten werden nach CEN/TS 17394 4:2021 bewertet.
Dieses Dokument gilt nicht für:
a)   Artikel für die Kinderpflege;
b)   Schuhe, Stiefel und ähnliche Fußbekleidung;
c)   Spielzeuge (siehe Anmerkung 2);
d)   sonstige mit Bekleidung verkaufte Artikel.
ANMERKUNG 1   Die vorstehenden Artikel werden durch andere Technische Komitees des CEN erfasst und fallen daher nicht in den Anwendungsbereich dieses Dokumentes.
ANMERKUNG 2   Verkleidungskostüme einschließlich Faschingskostümen sind Beispiele für Bekleidung, die auch Spiel¬zeug sind und in den Anwendungsbereich der Richtlinie über die Sicherheit von Spielzeug fallen.
Der Anwendungsbereich dieses Dokuments ist auf mechanisch angebrachte metallische Komponenten beschränkt. Derzeit werden Normen für weitere Komponenten von Kleidungsstücken erarbeitet.
—   EN 17394 2:2020, Textilien und textile Erzeugnisse — Teil 2: Sicherheit von Kinderbekleidung — Sicherheit der Befestigung von Knöpfen — Prüfverfahren
—   CEN/TS 17394 4:2021, Textilien und textile Erzeugnisse — Teil 4: Sicherheit von Kinderbekleidung — Sicherheit der Befestigung von Komponenten außer Knöpfen und mechanisch befestigten Verschlüssen — Prüfverfahren
Leistungsanforderungen sind in CEN/TS 17394 1:2021 enthalten.

Textiles et produits textiles - Partie 3 : Sécurité des vêtements d’enfants - Sécurité d’attache des boutons-pression métalliques appliqués mécaniquement - Méthode d’essai

Le présent document définit une méthode d’essai pour la sécurité d’attache des boutons-pression métalliques appliqués mécaniquement, fonctionnels et décoratifs, utilisés pour les vêtements d’enfants y compris, par exemple, les gants, les chapeaux, les écharpes, les articles de bonneterie, les cravates et les ceintures en textile.
IMPORTANT : Les oeillets et les rivets ne peuvent pas être soumis à l’essai au moyen de la présente méthode, car l’intégrité du composant, lorsqu’il est fixé au support textile, est gravement compromise lors de la préhension. Les oeillets et les rivets sont évalués tel que décrit dans le CEN/TS 17394 4:2021.
Le présent document ne s’applique pas aux :
a)   articles de puériculture ;
b)   chaussures, bottes et articles similaires ;
c)   jouets (voir NOTE 2) ;
d)   autres articles vendus avec le vêtement.
NOTE 1   Les articles ci-dessus sont couverts par d’autres Comités techniques CEN et n’entrent par conséquent pas dans le domaine d’application du présent document.
NOTE 2   Les déguisements y compris les costumes de carnaval sont des exemples de vêtements qui sont également des jouets et qui entrent dans le domaine d’application de la Directive relative à la sécurité des jouets.
Le domaine d’application du présent document se limite aux composants métalliques appliqués mécaniquement. Des travaux sont en cours dans le but d’élaborer des normes relatives à d’autres composants de vêtements :
-   EN 17394 2:2020, Textiles et produits textiles - Partie 2 : Sécurité des vêtements d’enfants - Sécurité d’attache des boutons - Méthode d’essai ;
-   CEN/TS 17394 4:2021, Textiles et produits textiles - Partie 4 : Sécurité des vêtements d’enfants - Sécurité d’attache des composants à l’exception des boutons et des boutons-pression métalliques appliqués mécaniquement - Méthode d’essai.
Des exigences relatives à la performance sont fournies dans le CEN/TS 17394 1:2021.

Tekstilije in tekstilni izdelki - 3. del: Varnost otroških oblačil - Varnost pritrditve mehansko pritrjenih kovinskih pritiskačev - Preskusna metoda

General Information

Status
Published
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Due Date
13-Jan-2021
Completion Date
13-Jan-2021

Buy Standard

Technical specification
-TS FprCEN/TS 17394-3:2019
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
kSIST-TS FprCEN/TS 17394-3:2019
01-september-2019

Tekstilije in tekstilni izdelki - 3. del: Varnost otroških oblačil - Varnost pritrditve

mehansko pritrjenih kovinskih pritiskačev - Preskusna metoda

Textiles and textile products - Part 3: Safety of children's clothing - Security of

attachment of metal mechanically applied press fasteners - Test method

Textilien und textile Produkte - Sicherheit von Kinderbekleidung - Teil 3: Sicherheit der

Befestigung von mechanisch befestigten Druckknöpfen - Prüfverfahren

Textiles et produits textiles - Partie 3 : Sécurité des vêtements d’enfants - Sécurité

d’attache des boutons-pression métalliques appliqués mécaniquement - Méthode d’essai

Ta slovenski standard je istoveten z: FprCEN/TS 17394-3
ICS:
61.020 Oblačila Clothes
97.190 Otroška oprema Equipment for children
kSIST-TS FprCEN/TS 17394-3:2019 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
kSIST-TS FprCEN/TS 17394-3:2019
---------------------- Page: 2 ----------------------
kSIST-TS FprCEN/TS 17394-3:2019
FINAL DRAFT
TECHNICAL SPECIFICATION
FprCEN/TS 17394-3
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
July 2019
ICS
English Version
Textiles and textile products - Part 3: Safety of children's
clothing - Security of attachment of metal mechanically
applied press fasteners - Test method

Textiles et produits textiles - Partie 3 : Sécurité des Textilien und textile Produkte - Sicherheit von

vêtements d'enfants - Sécurité d'attache des boutons- Kinderbekleidung - Teil 3: Sicherheit der Befestigung

pression métalliques appliqués mécaniquement - von mechanisch befestigten Druckknöpfen -

Méthode d'essai Prüfverfahren

This draft Technical Specification is submitted to CEN members for Vote. It has been drawn up by the Technical Committee

CEN/TC 248.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are

aware and to provide supporting documentation.

Warning : This document is not a Technical Specification. It is distributed for review and comments. It is subject to change

without notice and shall not be referred to as a Technical Specification.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. FprCEN/TS 17394-3:2019 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
kSIST-TS FprCEN/TS 17394-3:2019
FprCEN/TS 17394-3:2019 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

Introduction .................................................................................................................................................................... 4

1 Scope .................................................................................................................................................................... 5

2 Normative references .................................................................................................................................... 5

3 Terms and definitions ................................................................................................................................... 5

4 Sampling and selection of test specimens .............................................................................................. 7

5 Procedure........................................................................................................................................................... 7

5.1 General ................................................................................................................................................................ 7

5.2 Principle ............................................................................................................................................................. 7

5.3 Apparatus ........................................................................................................................................................... 7

5.3.1 Constant rate of extension (CRE) tensile-testing machine. .............................................................. 7

5.3.2 Upper grip .......................................................................................................................................................... 8

5.3.3 Lower grip .......................................................................................................................................................... 9

5.4 Atmosphere for conditioning and testing ........................................................................................... 10

5.5 Procedure........................................................................................................................................................ 11

5.5.1 Rate of extension or elongation .............................................................................................................. 11

5.5.2 Machine set-up and test specimen mounting .................................................................................... 11

6 Test report ...................................................................................................................................................... 12

Annex A (informative) Method of test for in-line production process control ................................... 13

Annex B (informative) Interlaboratory trial ................................................................................................... 14

Bibliography ................................................................................................................................................................. 15

---------------------- Page: 4 ----------------------
kSIST-TS FprCEN/TS 17394-3:2019
FprCEN/TS 17394-3:2019 (E)
European foreword

This document (FprCEN/TS 17394-3:2019) has been prepared by Technical Committee CEN/TC 248

“Textiles and Textile Products”, the secretariat of which is held by BSI.
This document is currently submitted to the vote on TS.
---------------------- Page: 5 ----------------------
kSIST-TS FprCEN/TS 17394-3:2019
FprCEN/TS 17394-3:2019 (E)
Introduction

The aim of this document is to assess the attachment strength of metal mechanically applied press

fasteners.

This document provides a method of test. A document providing a technical specification for security of

attachment of applied components for infants' clothing is under development.
This document has been developed from Annex B of CEN/TR 16792:2014.
---------------------- Page: 6 ----------------------
kSIST-TS FprCEN/TS 17394-3:2019
FprCEN/TS 17394-3:2019 (E)
1 Scope

This document defines a test method for security of attachment of functional and decorative metal

mechanically applied press fastners to children's clothing including garments such as gloves, hats,

scarves, hosiery, ties, and textile belts.

IMPORTANT: Eyelets and rivets cannot be assessed by this method as the integrity of the component

when attached to textile fabrics is destroyed in the gripping action. Eyelets and rivets shall be assessed

as described in FprCEN/TS 17394-4:2019.
This document does not apply to:
a) child care articles;
b) shoes, boots and similar footwear;
c) toys (see note 2);
d) other articles sold with clothing.

NOTE 1 The above items are covered by other CEN Technical Committees and as such are out of scope of this

document.

NOTE 2 Disguise costumes including carnival costumes are examples of clothing which are also toys and fall

within the scope of the Toy Safety Directive.

The scope of this technical specification only applies to metal mechanically applied components. Work

is in progress to developed standards for other garment components.

— prEN 17394-2:2019, Textiles and textile products -Safety of children's clothing – Security of

attachment of buttons – Test method

— FprCEN/TS 17394-4:2019, Textiles and textile products - Safety of Children's clothing – Security of

attachment of components except buttons and metal mechanically applied fasteners – Test method

Performance recommendations are provided in FprCEN/TS 17394-1:2019
2 Normative references
There are no normative references in this document.
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.

ISO and IEC maintain terminological databases for use in standardization at the following addresses:

• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
---------------------- Page: 7 ----------------------
kSIST-TS FprCEN/TS 17394-3:2019
FprCEN/TS 17394-3:2019 (E)
3.1
press fastener

fastening device consisting of a male component and a female component that are attached to different

parts of a garment and which are fastened by aligning the two components and pressing them together

Note 1 to entry: Press fasteners includes poppers and snaps.
Note 2 to entry: These may be functional or decorative.
3.2
rivet

component with two-part assembly, comprising a part (referred to as a burr) which is attached to the

outer surface of the garment by a tack which passes through the fabric from the reverse side

Note 1 to entry: Rivets are usually used as reinforcements, particularly on the corners of pockets on denim and

other casual garments.
Note 2 to entry: These may be functional or decorative.
3.3
eyelet

component used for example to reinforce a hole through a part of a garment, comprising a short metal

tube with a flange at one end which is fastened to the garment by pushing it through the hole and

compressing it against a die
Note 1 to entry: An eyelet may also include a washer on the reverse side.

Note 2 to entry: Eyelets are used to facilitate lacing or the insertion of a drawstring, to drain pockets and

ventilate a garment.
Note 3 to entry: These may be functional or decorative.
3.4
child or young person

person aged from birth up to age 14 years (that is up to and including 13 years and 11 months) which

includes all boys of height up to 182 cm and all girls of height up to 176 cm
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.