EN ISO 14405-1:2010/prA1
(Amendment)Geometrical product specifications (GPS) - Dimensional tolerancing - Part 1: Linear sizes (ISO 14405-1:2010/DAM 1:2013)
Geometrical product specifications (GPS) - Dimensional tolerancing - Part 1: Linear sizes (ISO 14405-1:2010/DAM 1:2013)
2013-12-05 GVN: WI deleted again after erroneous reactivation (see email in dataservice on 2013-12-05)
2013-10-25 LVO: WI deleted following cancellation of equivalent ISO project (see notification of 2013-10-24 in dataservice)
2013-09-11 EMA: Draft for 2nd // ENQ received in ISO/CS (see notification of 2013-09-10 in dataservice).
2012-06-05 EMA: Draft for // ENQ received in ISO/CS (see notification of 2012-06-04 in dataservice).
Geometrische Produktspezifikation (GPS) - Dimensionelle Tolerierung - Teil 1: Längenmaße (ISO 14405-1:2010/DAM 1:2013)
Spécification géométrique des produits (GPS) - Tolérancement dimensionnel - Partie 1: Tailles linéaires (ISO 14405-1:2010/DAM 1:2013)
Specifikacija geometrijskih veličin izdelka - Tolerance dimenzij - 1. del: Dolžinske mere - Dopolnilo 1 (ISO 14405-1:2010/DAM 1:2012)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2012
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND7ROHUDQFHGLPHQ]LMGHO 'ROåLQVNH
PHUH'RSROQLOR ,62 '$0
Geometrical product specifications (GPS) - Dimensional tolerancing - Part 1: Linear sizes
- Amendment 1 (ISO 14405-1:2010/DAM 1:2012)
Geometrische Produktspezifikation (GPS) - Dimensionelle Tolerierung - Teil 1:
Längenmaße - Änderung 1 (ISO 14405-1:2010/DAM 1:2012)
Spécification géométrique des produits (GPS) - Tolérancement dimensionnel - Partie 1:
Tailles linéaires - Amendement 1 (ISO 14405-1:2010/DAM 1:2012)
Ta slovenski standard je istoveten z: EN ISO 14405-1:2010/prA1
ICS:
17.040.10 Tolerance in ujemi Limits and fits
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
DRAFT
EN ISO 14405-1:2010
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
August 2012
ICS 17.040.30
English Version
Geometrical product specifications (GPS) - Dimensional
tolerancing - Part 1: Linear sizes - Amendment 1 (ISO 14405-
1:2010/DAM 1:2012)
Spécification géométrique des produits (GPS) - Geometrische Produktspezifikation (GPS) - Dimensionelle
Tolérancement dimensionnel - Partie 1: Tailles linéaires - Tolerierung - Teil 1: Längenmaße - Änderung 1 (ISO
Amendement 1 (ISO 14405-1:2010/DAM 1:2012) 14405-1:2010/DAM 1:2012)
This draft amendment is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee CEN/TC 290.
This draft amendment A1, if approved, will modify the European Standard EN ISO 14405-1:2010. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14405-1:2010/prA1:2012: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 14405-1:2010/prA1:2012) has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of
which is held by AFNOR.
This document is currently submitted to the parallel Enquiry.
Endorsement notice
The text of ISO 14405-1:2010/DAM 1:2012 has been approved by CEN as a EN ISO 14405-1:2010/prA1:2012
without any modification.
DRAFT AMENDMENT ISO 14405-1:2010/DAM 1
ISO/TC 213 Secretariat: DS
Voting begins on Voting terminates on
2012-08-09 2013-01-09
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ ORGANISATION INTERNATIONALE DE NORMALISATION
Geometrical product specifications (GPS) — Dimensional
tolerancing —
Part 1:
Linear sizes
AMENDMENT 1
Spécification géométrique des produits (GPS) — Tolérancement dimensionnel —
Partie 1: Tailles linéaires
AMENDEMENT 1
ICS 17.040.10
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for Standardization (ISO), and
processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
five-month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments received, will be
submitted to a parallel two-month approval vote in ISO and formal vote in CEN.
To expedite distribution, this document is circulated as received from the committee
secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at
publication stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME
STANDARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
© International Organization for Standardization, 2012
ISO 14405-1:2010/DAM 1
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user’s country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic,
photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ii © ISO 2012 – All rights reserved
ISO 14405-1:2010/DAM 1
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to ISO 14405-1:2010 was prepared by Technical Committee ISO/TC 213, Dimensional and
geometrical product specification and verification.
ISO 14405-1:2010/DAM 1
Introduction
ISO/TC 213/WG 12 Resolution Paris 231 (Paris 5/2011) and 232 (Paris 6/2011).
iv © ISO 2012 – All rights reserved
DRAFT AMENDMENT ISO 14405-1:2010/DAM 1
Geometrical product specifications (GPS) — Dimensional
tolerancing — Part 1: Linear sizes
st
Page 1, Scope, replace 1 sentence with:
“This part of ISO 14405 establishes the default specification operator for linear size and defines a number of
special specification operators for linear size for features of size i.e. "cylinder", "two parallel opposite planes",
"sphere", "circle" or "two parallel opposite straight lines".
For direct global linear size, add in the list “minimum zone size” after “minimum circumscribed size”,
At the end of the list, after range size, add:
"- quadratic range of sizes. "
Page 3, definition 3.2, replace note 3 with:
NOTE 3 Figures 1 and 2 illustrate a feature of size, type cylinder or two parallel opposite planes.
Page 3, definition 3.2, add the following note
NOTE 4 The features of linear size can be a cylinder, a sphere, two parallel opposite planes, a circle (cross section of a
revolute surface and a plane perpendicular to the axis of the revolute surface), two parallel opposite straight lines
(longitudinal section of a surface and a plane which is symmetrical to the axis for a revolute surface or a plane
perpendicular to symmetry plane of a prismatic surface).
Page 7, Figure 3 d) delete the right side view
Add the following note: "Any section size is given by the diameter of maximum inscribed circle defined in any
cross section".
Move the NOTE of Figure 3e) to the bottom of the figure before the title.
Page 5, replace definition 3.6 with the following:
"specification operator required by technical documentation, applicable only for all ISO basic GPS
specifications of the actual drawing, and containing only default specification operations in the default order"
Page 8, add a new definition
"3.11.1.4
minmax size
Chebychev size
size (3.8) characteristic defined as the size of the associated feature established from
extracted feature(s) with the minmax criterion
ISO 14405-1:2010/DAM 1
NOTE The minmax criterion gives without constraint of inside or outside material the medium feature of the minimum
zone including the real feature of size."
Page 12, add the following new definition
3.11.2.2.7
quadratic range of sizes
rank-order size (3.11.2.2) defined as the standard deviation of the set of values of a local size along and/or
around to the toleranced feature
Page 9, Figure 4, add the following figure e)
e) Minmax size
Page 13, Figure 8, add the key 9 (on the figure where the keys 1, 3, 4, 8 appear) with the corresponding text :
9 quadratic range of sizes: 0,30178
Page 13, replace the current definition 3.13 with
"set of several separate geometrical features considered as one feature of size (3.2)"
2 © ISO 2012 – All rights reserved
ISO 14405-1:2010/DAM 1
Page 14, Table 1 add the following lines
After GN
Minmax association criteria
At the end of the table
Quadratic range of sizes
Page 15, Table 2, replace "common tolerance" with "common feature of size" and add a new line at the end of
the table as follows:
flagnote 8 10 ± 0,1
Page 17, modify figures 9, 10 and 11 as follows:
Fig. 9a
replace -0,035 with -0,013
Fig.11a replace 25,900 with 20;000
25,860 19,087
Fig. 9b
replace -0,087 with -0,033
Fig 11b replace 20,000 with 20,000
19,970 19,067
And add the following NOTE
NOTE The three specifications of figures 9, 10, 11 are identical, but written in different ways. They all use the ISO
default specification operator for size.
Page 18, rename Figure 12 in Figure 12 a) and add the following Figure 12 b)
ISO 14405-1:2010/DAM 1
12a) 12b)
Page 18, replace NOTE 1 and NOTE 3 with:
NOTE 1 The default specification operator for this drawing is not the two point size but is changed to least squares size
(see Figure 12 a). Other examples can be:
“Size ISO 14405 “ changing the default specification operator to the envelope requirement (see Figure 12b) or
“Size ISO 14405 “changing the default specification operator to the circumference diameter, etc.
NOTE 3 To facilitate the reading of the drawing, it is possible to indicate all other types of modifier into brackets after
the default specification indication [see Figure 12b)]
Page 18, delete NOTE 2 and renumber the existing notes
th
Page 19, replace the 4 paragraph with the following
"The other specification modifiers shall be used in the following order (some modifiers may be omitted in a
tolerance specification) after the tolerance value or the tolerance code or the value(s) of the limit of size:
⎯ modifier for type of size characteristic : local size or global size or calculated size, e.g.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.