EN 13775-3:2003

Railway applications - Measuring of new and modified freight wagons - Part 3: Freight wagons with 2 wheelsets

This European Standard specifies requirements for measuring freight wagons with 2 wheelsets. This ensures that the measuring processes are applied in accordance with uniform criteria. It applies to new and modified freight wagons with 2 wheelsets. Provisions going beyond the scope of these requirements should be agreed upon by the contracting parties involved.
The measuring processes relate to the whole or parts of the underframes with or without add-ons if the geometrical structure does not permit anything else. Where appropriate, other measuring methods not specified here are necessary and should be specified in each individual case.

Bahnanwendungen - Vermessung von Güterwagen beim Neubau und bei Umbauten - Teil 3: Güterwagen mit 2 Radsätzen

In dieser Europäischen Norm sind die Anforderungen für das Vermessen von Güterwagen mit zwei Radsätzen festgelegt. Durch diese wird sichergestellt, daß Meßvorgänge nach einheitlichen Kriterien ausgeführt werden. Sie gilt für neue und umgebaute Güterwagen mit 2 Radsätzen. Über diese Anforderungen dieser Norm hinausgehende Forderungen sind zwischen den Vertragspartnern zu vereinbaren. Durch das Vermessen ist festzustellen, ob die Abweichungen von den Nennmaßen innerhalb der in den Teilen 2 bis 6 dieser Normenreihe festgelegten Toleranzen liegen.

Applications ferroviaires - Mesure des wagons lors de leur construction et lors de modifications - Partie 3 : Wagons à deux essieux

La présente Norme européenne précise les exigences concernant les mesures sur les wagons à deux essieux, qui assurent que les opérations de mesure sont effectuées en fonction de critères unifiés. Elle est applicable aux wagons à deux essieux neufs ou modifiés. Les prescriptions allant au-delà de la dite Norme doivent faire l'objet d'un contrat entre les parties concernées.
Les opérations de mesure se rapportent aux châssis dans leur totalité, avec ou sans superstructure, ou à certaines parties de ceux-ci lorsque leur conception géométrique ne permet pas de faire autrement. Il y a lieu, le cas échéant, de procéder à des opérations de mesure supplémentaires, non prévues ici, qui doivent être déterminées au cas par cas.

Železniške naprave– Merjenje novih in predelanih tovornih vagonov – 3.del: Dvoosni tovorni vagoni

General Information

• Status: Published
• Publication Date: 17-Jun-2003
• ICS: 45.060.20 - Trailing stock
• Technical Committee: CEN/TC 256 - Railway applications
• Drafting Committee: CEN/TC 256/WG 26 - Freight wagons
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 13-Jun-2022
• Directive: 93/38/EEC - Procurement procedures of entities operating in the water, energy, transport and telecommunications sectors
• Mandate: M/024 - Mandate to CEN/CENELEC/ETSI for programming and standardization in the field of railway equipment
• Ref Project: SIST EN 13775-3:2004 - Railway applications - Measuring of new and modified freight wagons - Part 3: Freight wagons with 2 wheelsets

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Železniške naprave– Merjenje
novih in predelanih tovornih vagonov – 3.del: Dvoosni tovorni vagoniBahnanwendungen - Vermessung von Güterwagen beim Neubau und bei Umbauten - Teil 3: Güterwagen mit 2 RadsätzenApplications ferroviaires - Mesure des wagons lors de leur construction et lors de modifications - Partie 3 : Wagons a deux essieuxRailway applications - Measuring of new and modified freight wagons - Part 3: Freight wagons with 2 wheelsets45.060.20Železniški vagoniTrailing stockICS:Ta slovenski standard je istoveten z:EN 13775-3:2003SIST EN 13775-3:2004en01-junij-2004SIST EN 13775-3:2004SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13775-3June 2003ICS 45.060.20English versionRailway applications - Measuring of new and modified freightwagons - Part 3: Freight wagons with 2 wheelsetsApplications ferroviaires - Mesure des wagons lors de leurconstruction et lors de modifications - Partie 3: Wagons àdeux essieuxBahnanwendungen - Vermessung von Güterwagen beimNeubau und bei Umbauten - Teil 3: Güterwagen mit 2RadsätzenThis European Standard was approved by CEN on 20 February 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13775-3:2003 ESIST EN 13775-3:2004

Control sheet form.27Annex B (informative)
Measuring processes on running gear.30Annex C (informative)
Terminology.33Bibliography.34SIST EN 13775-3:2004

be agreed upon by the contracting parties involved.The measuring processes relate to the whole or parts of the underframes with or without add-ons if thegeometrical structure does not permit anything else. Where appropriate, other measuring methods notspecified here are necessary and ought to be specified in each individual case.SIST EN 13775-3:2004
...