iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 12007-4:2012

(Main)

Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 4: Specific functional requirements for renovation

Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 4: Specific functional requirements for renovation

This European Standard describes specific functional requirements for the renovation of pipework in existing gas infrastructures. This European Standard is intended to be applied with the requirements of EN 12007-1.
This European Standard does not apply to pipework in above ground installations.
This European Standard covers the various renovation technologies for gas piping in the range of sizes covering gas mains and gas service lines and is intended to be applied in association with EN 12007-1. Certain pipe networks originally for other purposes can be considered for renovation technologies to make them suitable for gas infrastructure.
This European Standard specifies common basic principles for gas infrastructure. Users of this European Standard should be aware that more detailed national standards and/or code of practice may exist in the CEN member countries. This European Standard is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this European Standard, the national legislation/regulation should take precedence as illustrated in FprCEN/TR 13737-1.
FprCEN/TR 13737-1 gives:
-   clarification of all legislations/regulations applicable in a member state;
-   if appropriate, more restrictive national requirements;
-   a national contact point for the latest information.

Gasinfrastruktur - Rohrleitungen mit einem maximal zulässigen Betriebsdruck bis einschließlich 16 bar - Teil 4: Spezifische funktionale Anforderungen für die Sanierung

Diese Europäische Norm beschreibt besondere funktionale Anforderungen für die Sanierung von Leitungs-anlagen als Teil bestehender Gasinfrastruktursysteme. Diese Europäische Norm soll in Verbindung mit den Anforderungen der EN 12007-1 angewendet werden.
Diese Europäische Norm gilt nicht für Leitungsanlagen in oberirdischen Anlagen.
Diese Europäische Norm behandelt die verschiedenen Sanierungstechnologien für Gasrohrleitungen in dem Größenbereich der Hauptgasleitungen und Gashausanschlussleitungen und sie soll in Verbindung mit EN 12007-1 angewendet werden. Bestimmte Leitungsnetzwerke, die ursprüngliche für andere Zwecke gedacht waren, können für Sanierungstechnologien in Betracht gezogen werden, um sie für die Verwendung als Gasinfrastruktur tauglich zu machen.
Diese Europäische Norm beschreibt allgemeine Grundsätze der Gasinfrastruktur. Die Anwender dieser Europäischen Norm sollten sich dessen bewusst sein, dass detailliertere nationale Normen bzw. Technische Regeln in den CEN-Mitgliedsländern existieren können.
Diese Europäische Norm soll in Verbindung mit diesen, die oben erwähnten allgemeinen Grundsätze darlegenden nationalen Normen und/oder Technischen Regeln angewendet werden.
Für den Fall eines Konflikts zwischen strengeren nationalen gesetzlichen Anforderungen/Bestimmungen und den Anforderungen dieser Europäischen Norm ist den nationalen gesetzlichen Anforderungen/Bestimmungen wie in CEN/TR 13737 (alle Teile) ausgeführt Vorrang einzuräumen.
CEN/TR 13737 (alle Teile) enthält
-   eine Klarstellung aller geltenden Rechtsvorschriften/Bestimmungen eines Mitgliedstaats;
-   ggf. weitergehende strengere nationale Anforderungen;
-   einen nationalen Ansprechpartner für die Weitergabe neuester Informationen.

Infrastructures gazières - Canalisations pour pression maximale de service inférieure ou égale à 16 bar - Partie 4: Prescriptions fonctionnelles spécifiques pour la rénovation

La présente Norme européenne décrit les recommandations fonctionnelles spécifiques pour la rénovation de tuyauteries dans les infrastructures gazières existantes. La présente Norme européenne est destinée à être appliquée en association avec l’EN 12007-1.
La présente Norme européenne ne s'applique pas à la tuyauterie des installations hors sol.
La présente Norme européenne couvre les différentes technologies de rénovation des tuyauteries à gaz dans une palette de tailles comprenant les conduites de distribution et de branchement du gaz et est destinée à être appliquée en association avec l’EN 12007-1. Certains réseaux de canalisations utilisés à l'origine à d'autres fins peuvent être considérés par des technologies de rénovation pour les rendre aptes à l'infrastructure du gaz.
La présente Norme européenne spécifie les principes de base communs pour les systèmes d'alimentation en gaz. Il convient que les utilisateurs de la présente Norme européenne gardent à l'esprit l'existence éventuelle, dans les pays membres du CEN, de codes de pratique et/ou de normes nationales plus détaillées.
La présente Norme européenne est destinée à s'appliquer conjointement avec ces normes nationales et/ou codes de pratique, qui détaillent les principes de base précités.
En cas de conflits en termes d’exigences plus restrictives dans la réglementations/législation nationale vis-à-vis des exigences de cette Norme européenne, la réglementations/législation nationale doit s’appliquer comme illustré dans le CEN/TR 13737.
Le CEN/TR 13737 donne :
-   la clarification de toutes les législations/règlements applicables dans un état membre ;
-   si approprié, des exigences nationales plus restrictives ;
-   un point de contact national pour une information ultérieure.

Infrastruktura za plin - Cevovodni sistemi za najvišji delovni tlak do vključno 16 bar - 4. del: Posebne funkcionalne zahteve za obnovo

Ta evropski standard poleg splošnih funkcionalnih zahtev iz standarda EN 12007-1 opisuje posebne funkcionalne zahteve za polietilenske (PE) cevovodne sisteme za: a) najvišji obratovalni tlak (MOP) do vključno 10 bar, b) obratovalno temperaturo med –20 °C in +40 °C. Ta evropski standard zajema tri vrste cevi: polietilenske cevi s kakršnimi koli identifikacijskimi črtami, polietilenske cevi s koekstrudiranimi sloji na zunanji in/ali notranji strani cevi, polietilenske cevi s sosednjim termoplastičnim dodatnim slojem, ki ga je mogoče odluščiti, na zunanji strani cevi. Ta evropski standard določa splošna osnovna načela za infrastrukturo za plin. Uporabniki tega evropskega standarda se morajo zavedati, da lahko v državah članicah CEN obstajajo podrobnejši nacionalni standardi in/ali kodeks ravnanja. Ta evropski standard je namenjen uporabi v povezavi s temi nacionalnimi standardi in/ali kodeksi ravnanja, ki določajo zgoraj navedena osnovna načela. Kadar so strožje zahteve v nacionalni zakonodaji/predpisu v nasprotju z zahtevami iz tega evropskega standarda, ima prednost nacionalna zakonodaja/predpis, kot je navedeno v standardu CEN/TR 13737 (vsi deli). Standard CEN/TR 13737 (vsi deli) vsebuje: pojasnitev vse zakonodaje/predpisov, ki se uporabljajo v državi članici, po potrebi strožje nacionalne zahteve in nacionalno kontaktno točko za najnovejše informacije.

General Information

Status
Published
Publication Date
31-Jul-2012
Withdrawal Date
27-Feb-2013
ICS
23.040.01 - Pipeline components and pipelines in general
Technical Committee
CEN/TC 234 - Gas infrastructure
Drafting Committee
CEN/TC 234/WG 2 - Gas supply systems up to and including 16 bar and pressure testing
Current Stage
9060 - Closure of 2 Year Review Enquiry - Review Enquiry
Start Date
02-Dec-2024
Completion Date
02-Dec-2024
Mandate
M/017 - Standardization mandate to CEN in the field of equipment and installation for the transmission and distribution of gas
Ref Project
SIST EN 12007-4:2013 - Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 4: Specific functional requirements for renovation

Relations

Replaces
EN 12007-4:2000 - Gas supply systems - Pipelines for maximum operating pressure up to and including 16 bar - Part 4: Specific functional recommendations for renovation
Effective Date
08-Jun-2022

Buy Standard

EN 12007-4:2013EN 12007-4:2013
PreviousNext
Standard
EN 12007-4:2013
English language
36 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Gasinfrastruktur - Rohrleitungen mit einem maximal zulässigen Betriebsdruck bis einschließlich 16 bar - Teil 4: Spezifische funktionale Anforderungen für die SanierungInfrastructures gazières - Canalisations pour pression maximale de service inférieure ou égale à 16 bar - Partie 4: Recommandations fonctionnelles spécifiques pour la rénovationGas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 4: Specific functional requirements for renovation91.140.40Sistemi za oskrbo s plinomGas supply systemsICS:Ta slovenski standard je istoveten z:EN 12007-4:2012SIST EN 12007-4:2013en,fr,de01-januar-2013SIST EN 12007-4:2013SLOVENSKI
STANDARDSIST EN 12007-4:20001DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12007-4
August 2012 ICS 23.040.01 Supersedes EN 12007-4:2000English Version
Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 4: Specific functional requirements for renovation
Infrastructures gazières - Canalisations pour pression maximale de service inférieure ou égale à 16 bar - Partie 4: Prescriptions fonctionnelles spécifiques pour la rénovation Gasinfrastruktur - Rohrleitungen mit einem maximal zulässigen Betriebsdruck bis einschließlich 16 bar - Teil 4: Spezifische funktionale Anforderungen für die Sanierung This European Standard was approved by CEN on 24 May 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12007-4:2012: ESIST EN 12007-4:2013

Chart of renovation techniques . 12Annex B (informative)
Advantages and disadvantages of renovation techniques . 13Annex C (informative)
Renovation with continuous or discrete pipe . 16C.1 Definition . 16C.2 Description . 16C.3 Conditions of application . 16C.4 Implementation . 17C.4.1 Preparation . 17C.4.2 Execution . 17Annex D (informative)
Lining with close-fit pipe . 20D.1 Definition . 20D.2 Description . 20D.3 Conditions of application . 20D.4 Implementation . 21D.4.1 Materials . 21D.4.2 Preparation . 21D.4.3 Execution . 21Annex E (informative)
Lining with cured-in-place pipe . 23E.1 Definition . 23E.2 Description . 23E.3 Conditions of application . 23E.4 Implementation . 23E.4.1 Preparation . 23E.4.2 Execution . 24SIST EN 12007-4:2013

Renovation by bursting or splitting existing pipe . 25F.1 Definition . 25F.2 Description . 25F.3 Conditions of application . 25F.4 Implementation . 25F.4.1 Preparation . 25F.4.2 Execution. 26Annex G (informative)
Renovation by the pulling or pushing of the existing pipe . 27G.1 Definition . 27G.2 Description . 27G.3 Conditions of application . 27G.4 Implementation . 27G.4.1 Preparation . 27G.4.2 Execution. 27Annex H (informative)
Joint repairs . 29H.1 Definition . 29H.2 Description . 29H.3 Conditions of application . 29H.3.1 General . 29H.3.2 Internal methods . 29H.3.3 External methods − Commissioned pipework . 30H.4 Implementation . 30H.4.1 Internal repairs . 30H.4.2 External repairs − Commissioned pipework . 31H.5 Testing . 31H.6 Commissioning . 32Annex I (informative)
Resin lining . 33I.1 Definition . 33I.2 Description . 33I.3 Conditions of application . 33I.4 Implementation . 33I.4.1 Preparation . 33I.4.2 Execution . 33I.4.3 Testing . 34I.4.4 Commissioning .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 12007-5:2024(Main)
Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 5: Service lines - Specific functional requirements
SIST EN 12007-5:2025

This document describes the specific functional requirements for the transportation of gases (gaseous energy carriers) through service lines in addition to the general functional requirements of EN 12007 1 for:
a)   a maximum operating pressure (MOP) up to and including 16 bar;
b)   an operating temperature between −20 °C and +40 °C;
c)   gases and blends of gases which are in the gaseous state when conveyed in the gas pipeline infrastructure such as hydrogen, hydrogen rich, and methane rich gases, dimethyl ether (DME) and propane and butanes used for combustion and/or as feedstock, excluding steam and compressed air, where technical evaluation has ensured that operating conditions, constituents and properties of the gas do not affect the safe operation and maintenance of the service line.
It applies to their design, construction, commissioning, decommissioning, operation, maintenance, extension and other associated works including safety and environmental aspects. The service line is the physical asset comprising of pipework from the gas main branch saddle or top tee to the outlet of the distribution system operator’s nominated point(s) of delivery (for example: isolation valve, regulator, meter connection or combination of regulator and isolation valve).
This document does not apply retrospectively to installations before the publication date unless specifically stated.
Specific functional requirements for:
—   polyethylene pipelines are given in EN 12007 2;
—   steel pipelines are given in EN 12007 3;
—   polyamide (PA-U) pipelines are given in CEN/TS 12007 6;
—   pipework for buildings are given in EN 1775;
—   pressure regulating installations are given in EN 12279 or EN 12186;
—   pressure testing, commissioning and decommissioning are given in EN 12327;
—   safety management system (SMS) and pipeline integrity management system (PIMS) are given in EN 17649.
This document specifies common basic principles for gas infrastructure. Users of this document are expected to be aware that there can exist more detailed national standards and/or codes of practice in the CEN member countries. This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of terms of additional requirements in legislation/regulation than in this document, CEN/TR 13737 (all parts) illustrates these terms.
CEN/TR 13737 gives:
—   description of legislations/regulations applicable in a member state;
—   if appropriate, more restrictive national requirements;
—   a national contact point for the latest information.

  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1594:2024(Main)
Gas infrastructure - Pipelines for maximum operating pressure over 16 bar - Functional requirements
SIST EN 1594:2024

This document describes the functional requirements for pipelines for maximum operating pressure over 16 bar. This document also describes the mechanical requirements for pipework in stations with a maximum operating pressure greater than 16 bar.
NOTE 1   Welding requirements are described in EN 12732. Functional requirements for stations are given in EN 1776, EN 1918-5, EN 12186, and EN 12583.
This document is applicable for transporting gas via onshore high-pressure steel pipeline infrastructures, where the following applies:
-   onshore:
-   from the point where the pipeline first crosses what is normally accepted as battery limit between onshore and offshore, and that is not located within commercial or industrial premises as an integral part of the industrial process on these premises except for any pipelines and facilities supplying such premises;
-   pipeline system with a starting point onshore, also when parts of the pipeline system on the mainland subsequently cross fjords, lakes, etc.
-   high pressure: gas with a maximum operating pressure over 16 bar and a design temperature between −40 °C and 120 °C.
-   steel pipeline infrastructure: infrastructure consisting of pipeline components, such as pipes, valves, couplings and other equipment, restricted to components made of unalloyed or low alloyed carbon steel and joined by welds, flanges or mechanical couplings.
-   gas: non-corrosive natural gas, biomethane gas, hydrogen gas and mixtures of these gases where technical evaluation has ensured that operating conditions or constituents or properties of the gas do not affect the safe operation of the pipeline.
Gas infrastructures covered by this document begin after the gas producer's metering station.
NOTE 2   The functional demarcation of the pipeline system is usually directly after an isolating valve of the installation, but can differ in particular situations. The functional demarcation of the pipeline system is usually located on an isolating valve of the installation, but can differ in particular situations.
A schematic representation of pipelines for gas infrastructure is given in Figure 1.
This document can also be applied to the repurposing of existing pipelines.
[Figure 1 - Schematic representation of pipelines for gas supply over 16 bar]
This document specifies common basic principles for gas infrastructure. Users of this standard are expected to be aware that more detailed national standards and/or code of practice can exist in the CEN member countries.
This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this standard, the national legislation/regulation takes precedence as illustrated in CEN/TR 13737.
CEN/TR 13737 gives:
-   clarification of all legislations/regulations applicable in a member state;
-   if appropriate, more restrictive national requirements;
-   a national contact point for the latest information.

  • Standard
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15001-2:2023(Main)
Gas supply systems - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 2: Detailed functional requirements for commissioning, operation and maintenance
SIST EN 15001-2:2023

This European Standard specifies detailed functional requirements for the commissioning, operation and maintenance of
-   industrial gas installations and assemblies with an operating pressure greater than 0,5 bar and of
-   non-industrial gas installations (residential and commercial) with an operating pressure greater than 5 bar,
starting from the outlet of the network operator’s point of delivery up to the inlet connection to the gas appliance; normally the inlet isolation valve. This European Standard also covers the pipework to the inlet connection of a gas appliance that is not included within the scope of the appliance standard.
NOTE   The use of the term installation and pipework is interchangeable.
Apart from the exceptions stated below, this standard applies to gas installations operating at ambient temperatures between -20 °C and 40 °C and operating pressures up to and including 60 bar. For operating conditions outside these limitations, reference should additionally be made to EN 13480 for metallic pipework.
For industrial gas installations up to and including 0,5 bar and for non-industrial (residential and commercial) gas installations up to and including 5 bar EN 1775 applies.
For gas installations that do not fall within the scope of EN 1775 or other European Standards, this European Standard applies.
In this European Standard, the term "gas" refers to combustible gases, which are gaseous at 15 °C and 1 013 mbar absolute atmospheric pressure. These gases are commonly referred to as manufactured gas, natural gas or Liquefied Petroleum Gas (LPG). They are also referred to as first, second or third family gases as classified in Table 1 of EN 437:2003+A1:2009. The given values are considered as normal conditions for all volumes given in this standard.
This European Standard is applicable to installation pipework for the carriage of:
-   processed, non-toxic and non-corrosive natural gas according to EN 437:2003+A1:2009 and EN 16726 -Gas infrastructure - Quality of gas - Group H”,
-   vaporized LNG,
-   biomethane, complying with EN 16723-1,
-   vaporized LNG.
NOTE   The specification of vaporized LNG is equal to that of natural gas as classified in EN 437:2003+A1:2009.
This European Standard does not cover pipework for hydrogen rich gases that fall outside the definitions within EN 437:2003+A1:2009. LPG storage vessels (including all ancillaries fitted directly to storage vessels) are excluded. Also excluded are LPG installations and sections of LPG installations operating at vapour pressure (e.g. between the storage vessel and its pressure regulator).
In this European Standard, all pressures are gauge pressures unless otherwise stated.
This European Standard specifies common basic principles for gas supply systems. Users of this European Standard should be aware that more detailed national standards and/or code of practice may exist in the CEN member countries.
This European Standard is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
For gas installations within the scope of this standard, national legislation and regulations have to be taken into account.
Functional requirements for design, selection of materials, construction, inspection and testing of industrial gas installations and assemblies with an operating pressure greater than 0,5 bar and of gas installations greater than 5 bar in buildings and areas intended for residential, commercial, public and mixed uses are described in EN 15001-1.
Generally, additional safety precautions may be necessary where non odorized gas is used. For non-industrial purposes, the gas should be odorized.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15001-1:2023(Main)
Gas Infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 1: Detailed functional requirements for design, materials, construction, inspection and testing
SIST EN 15001-1:2023

This European Standard specifies detailed functional requirements for the design, selection of materials, construction, inspection and testing of:
-   industrial gas installation pipework and assemblies with an operating pressure greater than 0,5 bar; and
-   non-industrial gas installation pipework (residential and commercial) with an operating pressure greater than 5 bar in buildings;
starting from the outlet of the network operator’s point of delivery up to the inlet connection to the gas appliance; normally the inlet isolation valve. This standard also covers the pipework to the inlet connection of a gas appliance that is not included within the scope of the appliance standard.
NOTE 1   The use of the term installation and pipework is interchangeable.
Apart from the exceptions stated below, this standard applies to gas installations operating at ambient temperatures between −20 °C and 40 °C and operating pressures up to and including 60 bar. For operating conditions outside these limitations, reference should additionally be made to EN 13480 (all parts) for metallic pipework.
For industrial gas installations up to and including 0,5 bar and for non-industrial (residential and commercial) gas installations up to and including 5 bar in buildings, EN 1775 applies.
For gas installations that do not fall within the scope of EN 1775 or other European Standards, this standard applies.
In this European Standard, the term “gas“ refers to combustible gases, which are gaseous at 15 °C and 1 013 mbar absolute atmospheric pressure (normal conditions). These gases are commonly referred to as manufactured gas, natural gas or Liquefied Petroleum Gas (LPG). They are also referred to as first, second or third family gases as classified in EN 437:2003+A1:2009, Table 1. The given values are considered as normal conditions for all volumes given in this standard.
This European Standard is applicable to installation pipework for the carriage of:
-   processed, non-toxic and non-corrosive natural gas according to EN 437:2003+A1:2009 and EN 16726 "Gas infrastructure - Quality of gas - Group H";
-   vaporized LPG;
-   biomethane, complying with EN 16723 1;
-   vaporized LNG.
NOTE 2   The specification of vaporized LNG is equal to that of natural gas as classified in EN 437:2003+A1:2009.
This European Standard does not cover pipework for hydrogen rich gases that fall outside the definitions within EN 437:2003+A1:2009.
LPG storage vessels (including all ancillaries fitted directly to storage vessels) are excluded. Also excluded are LPG installations and sections of LPG installations operating at vapour pressure in the liquid state (e.g. between the storage vessel and any pressure regulator).
In this standard, all pressures are gauge pressures unless otherwise stated.
This standard has been harmonized to address the essential safety requirements of the Pressure Equipment Directive (PED, 2014/68/EU [formerly 97/23/EC]) relevant for the joining of gas installation pipework (assemblies) falling within the scope of the PED. These are listed in Annex ZA. However, "this Directive does not cover the assembly of pressure equipment on the site and under the responsibility of the user, as in the case of industrial installations" (PED, Preamble, 7th recital, last paragraph).
Although in this respect, the standard takes into account the essential safety requirements of the PED, no inference can be drawn from this as to whether or not the installation or parts of the installation falls within the scope of the PED. Reference should therefore be made to the PED and relevant national legislation.
This European Standard specifies common basic principles for gas supply systems. Users of this European Standard should be aware (...)

  • Standard
    131 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17649:2022(Main)
Gas infrastructure - Safety Management System (SMS) and Pipeline Integrity Management System (PIMS) - Functional requirements
SIST EN 17649:2022

This document specifies requirements on the development and implementation of a Safety Management System (SMS) and a Pipeline Integrity Management System (PIMS). The SMS is applicable for system operators of a gas infrastructure. The PIMS is applicable for system operators of gas infrastructure with a maximum operating pressure (MOP) over 16 bar.
This document refers to all activities and processes related to safety aspects and performed by system operators of a gas infrastructure, including those activities entrusted to contractors. It includes safety-related provisions on operation of the gas infrastructure.
This document is applicable to infrastructure for the conveyance of processed, non-toxic and non-corrosive natural gas according to EN ISO 13686 and gases such as biomethane and hydrogen and to mixtures of these gases with natural gas.
This document covers also gases classified as group H, that are to be transmitted, injected into and from storages, distributed and utilized, as specified in EN 16726. For the requirements and test methods for biomethane at the point of entry into a natural gas network, reference is made to EN 16723-1.
This document can be applied for gas infrastructure conveying gases of the 3rd gas family as classified in EN 437 or for other gases such as carbon dioxide.
Specific requirements for occupational health and safety are excluded from this document. For these, other European and/or international standards, e.g. ISO 45001, apply.
This document specifies common basic principles for gas infrastructure. It is important that users of this document are expected to be aware that more detailed national standards and/or codes of practice exist in the CEN member countries. This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this document, the national legislation/regulation takes precedence as illustrated in CEN/TR 13737 (all parts).
NOTE CEN/TR 13737 (all parts) contains:
- clarification of relevant legislation/regulations applicable in a country;
- if appropriate, more restrictive national requirements;
- national contact points for the latest information.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 16787:2014(Main)
Industrial Gas Installation - Guideline
SIST-TP CEN/TR 16787:2015

This Technical Report applies to safety and operational topics for equipment and pipework systems installed within industrial premises which may be used for process and non-process applications such as Heating, Power Generation, Incineration, etc.
It is applicable to a range of combustible gases used within an industrial environment. The gas plant may include normal combustion with air and/or oxygen, catalytic oxidation or cracking (e.g. as in a refinery).
The user of gas equipment and pipework systems has a responsibility to ensure the safety of the design, of plant operation and plant maintenance.
For piped supplies of gas to a site this Technical Report applies to the system downstream of the ‘point of delivery’. The term, ‘point of delivery’ refers to the isolation valve (or combination of regulator and isolation valve) located before or after the metering station, as will be defined by the particular EU member state national legislation.
The guidance in this Technical Report may also apply to gases generated for the sites own use, such as coke oven gas, site bio-gas plant, site LPG/air plant etc.

  • Technical report
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Technical report
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12007-1:2012(Main)
Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 1: General functional requirements
SIST EN 12007-1:2013

This European Standard describes the general functional requirements for pipelines up to the point of delivery, and also for buried sections of pipework after the point of delivery, for maximum operating pressures up to and including 16 bar for gaseous fuels in accordance with EN 437:1993+A1:2009, Table 1. It applies to their design, construction, commissioning, decommissioning, operation, maintenance, renovation, extension and other associated works.
This European Standard does not apply to the materials, design, construction, testing and commissioning of gas infrastructures in use prior to the publication of this European Standard. However, this European Standard does apply to the operation, maintenance, renovation and extension of all gas infrastructures.
Specific functional requirements for polyethylene pipelines are given in EN 12007-2, for steel pipelines in EN 12007-3 and for the renovation of pipelines in EN 12007-4. Functional recommendations for pipework for buildings are given in EN 1775. Functional requirements for service lines are given in prEN 12007-5.
Functional requirements for pressure testing, commissioning and decommissioning are given in EN 12327.
Functional requirements for measuring systems are given in EN 1776.
Functional requirements for pressure regulating stations are given in EN 12186.
Functional requirements for pressure regulating installations are given in EN 12279.
Functional requirements for gas transmission are given in EN 1594.
This European Standard specifies common basic principles for gas infrastructure. Users of this European Standard should be aware that more detailed national standards and/or code of practice may exist in the CEN member countries. This European Standard is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this European Standard, the national legislation/regulation should take precedence as illustrated in FprCEN/TR 13737-1.
FprCEN/TR 13737-1 gives:
-   clarification of all legislations/regulations applicable in a member state;
-   if appropriate, more restrictive national requirements;
-   a national contact point for the latest information.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12007-5:2024(Main)
Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 5: Service lines - Specific functional requirements
SIST EN 12007-5:2025

This document describes the specific functional requirements for the transportation of gases (gaseous energy carriers) through service lines in addition to the general functional requirements of EN 12007 1 for:
a)   a maximum operating pressure (MOP) up to and including 16 bar;
b)   an operating temperature between −20 °C and +40 °C;
c)   gases and blends of gases which are in the gaseous state when conveyed in the gas pipeline infrastructure such as hydrogen, hydrogen rich, and methane rich gases, dimethyl ether (DME) and propane and butanes used for combustion and/or as feedstock, excluding steam and compressed air, where technical evaluation has ensured that operating conditions, constituents and properties of the gas do not affect the safe operation and maintenance of the service line.
It applies to their design, construction, commissioning, decommissioning, operation, maintenance, extension and other associated works including safety and environmental aspects. The service line is the physical asset comprising of pipework from the gas main branch saddle or top tee to the outlet of the distribution system operator’s nominated point(s) of delivery (for example: isolation valve, regulator, meter connection or combination of regulator and isolation valve).
This document does not apply retrospectively to installations before the publication date unless specifically stated.
Specific functional requirements for:
—   polyethylene pipelines are given in EN 12007 2;
—   steel pipelines are given in EN 12007 3;
—   polyamide (PA-U) pipelines are given in CEN/TS 12007 6;
—   pipework for buildings are given in EN 1775;
—   pressure regulating installations are given in EN 12279 or EN 12186;
—   pressure testing, commissioning and decommissioning are given in EN 12327;
—   safety management system (SMS) and pipeline integrity management system (PIMS) are given in EN 17649.
This document specifies common basic principles for gas infrastructure. Users of this document are expected to be aware that there can exist more detailed national standards and/or codes of practice in the CEN member countries. This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of terms of additional requirements in legislation/regulation than in this document, CEN/TR 13737 (all parts) illustrates these terms.
CEN/TR 13737 gives:
—   description of legislations/regulations applicable in a member state;
—   if appropriate, more restrictive national requirements;
—   a national contact point for the latest information.

  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13480-4:2024(Main)
Metallic industrial piping - Part 4: Fabrication and installation
SIST EN 13480-4:2024

This document specifies the requirements for fabrication and installation of piping systems, including supports, designed in accordance with EN 13480-3:2024.

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13480-6:2024(Main)
Metallic industrial piping - Part 6: Additional requirements for buried piping
SIST EN 13480-6:2024

This document specifies requirements for industrial piping either totally buried or partly buried and partly run in sleeves or similar protection. It is used in conjunction with the other six parts of
EN 13480:2024 series.
Where buried piping subject to this standard connects to piping installed under other jurisdiction such as pipelines, the transition can be made at a closing element e.g. an isolating or regulating valve separating the two sections. This can be close to the boundary of the industrial site, but can be inside or outside the boundary.
Operating temperature up to 75 °C.
NOTE   For higher temperatures reference can be made to EN 13941-1:2019+A1:2021 and EN 13941 1:2019+A1:2021, but it is kept in mind, that CEN/TC 107 only deals with pre-insulated piping with temperatures up to 140 °C and diameters up to 800 mm, which is state of the art for these products.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day