EN ISO 6945:1996
(Main)Rubber hoses - Determination of abrasion resistance of the outer cover (ISO 6945:1991)
Rubber hoses - Determination of abrasion resistance of the outer cover (ISO 6945:1991)
Gummischläuche - Bestimmung des Verschleißverhaltens der Außenschicht (ISO 6945:1991)
Diese Internationale Norm legt ein Verfahren zur Bestimmung des Verschleißverhaltens der Außenschicht von Gummischläuchen fest. Dieses Verfahren ist vorzugsweise zu verwenden für die Prüfung von Hydraulikschläuchen mit Textil- und Drahtgeflechteinlage mit einer normalerweise glatten und gleichmäßigen Außenschicht, und für andere Schläuche ähnlicher Ausführung.
Tuyaux en caoutchouc - Détermination de la résistance à l'abrasion du revêtement extérieur (ISO 6945:1991)
Gumene cevi - Ugotavljanje odpornosti proti obrabi zunanje prevleke (ISO 6945:1991)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 6945:2000
01-december-2000
Gumene cevi - Ugotavljanje odpornosti proti obrabi zunanje prevleke (ISO
6945:1991)
Rubber hoses - Determination of abrasion resistance of the outer cover (ISO 6945:1991)
Gummischläuche - Bestimmung des Verschleißverhaltens der Außenschicht (ISO
6945:1991)
Tuyaux en caoutchouc - Détermination de la résistance a l'abrasion du revetement
extérieur (ISO 6945:1991)
Ta slovenski standard je istoveten z: EN ISO 6945:1996
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
SIST EN ISO 6945:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 6945:2000
---------------------- Page: 2 ----------------------
SIST EN ISO 6945:2000
---------------------- Page: 3 ----------------------
SIST EN ISO 6945:2000
---------------------- Page: 4 ----------------------
SIST EN ISO 6945:2000
INTERNATIONAL
STANDARD
Second edition
1991-12-01
- Determination of abrasion
Rubber hoses
resistance of the outer cover
Tuyaux en caoutchouc - D&termination de la r&sistance 3 / ‘abrasion du
rev&temen t ext&ieur
Reference number
IS0 6945: 1991 (E)
---------------------- Page: 5 ----------------------
SIST EN ISO 6945:2000
IS0 6945:1991(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work
of preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, govern-
mental and non-governmental, in liaison with ISO, also take part in the
work. IS0 collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. ‘Publication as an Inter-
national Standard requires approval by at least 75 % of the member
bodies casting a vote.
International Standard IS0 6945 was prepared by Technical Committee
ISO/TC 45, Rubber and rubber products, Sub-Committee SC 1, Hoses
(rubber and plastics).
This second edition cancels and replaces the first edition
(IS0 6945:1983), of which it constitutes a technical revision.
0 IS0 1991
All rights reserved. No part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without
permlsslon in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-1211 Gen&ve 20 l Switzerland
Printed in Switzerland
ii
---------------------- Page: 6 ----------------------
SIST EN ISO 6945:2000
~--~ ~~ --~~
IS0 69431991 (E)
INTERNATIONAL STANDARD
- Determination of abrasion resistance of the
Rubber hoses
outer cover
1 Scope 3 Apparatus
This International Standard specifies a method for
3.1 Wheel and crank arrangement, capable of
the determination of the abrasion resistance of the
moving the abrading tool 100 mm back and forth
outer cover of rubber hoses.
along the test piece with sinusoidal motion at a rate
of I,25 Hz (one cycle equals 200 mm of travel). A
This method is intended primarily for testing hy-
typical arrangement is shown in figure 1.
draulic hoses having textile or wire reinforcement
and a nominally smooth and parallel cover, and
The traversing arrangement shall be designed to
other hoses of a similar type. ensure that:
The method is not intended for predicting product
a) the mid-point of the traversed length is coinci-
abrasion life, but is suitable for the comparison of
dent with the mid-point of the assembled hose
quality levels.
and mandrel;
This International Standard does not specify the
b) the axes of the abrading tool and hose are mu-
number of cycles which should be completed in
tually perpendicular at the mid-point;
each test; this number will be specified in the ap-
propriate product specification.
c) the plane of travel is parallel to the longitudinal
axis of the test piece.
2 Normative references 3.2 Recording device, to record the number of cy-
cles completed, and capable of being pre-set to ter-
minate the test after completion of the specified
The following standards contain provisions which,
number of cycles.
through reference in this text, constitute provisions
of this International Standard. At the time of publi-
cation, the editions indicated were valid. All stan- 3.3 Abrading tool, manufactured from tool steel
dards are subject to revision, and parties to
S 9 in accordance with IS0 4957, heat-treated to
agreements based on this International Standard
give a minimum hardness
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.