EN ISO 8130-16:2023
(Main)Coating powders - Part 16: Determination of density by liquid displacement in a measuring cylinder (ISO 8130-16:2022)
Coating powders - Part 16: Determination of density by liquid displacement in a measuring cylinder (ISO 8130-16:2022)
This document specifies a method for determining the density of coating powders by liquid displacement in a measuring cylinder. The method is based on a determination of the mass and the volume of a test portion. It can be used for all types of coating powders.
NOTE If the powder does not swell in contact with the displacement liquid used and if the displacement liquid replaces the air between the powder particles, it can then be used and compared with the method described in ISO 8130-3.
Pulverlacke - Teil 16: Bestimmung der Dichte mittels Flüssigkeitsverdrängung in einem Messzylinder (ISO 8130‑16:2022)
Poudres pour revêtement - Partie 16: Détermination de la masse volumique par déplacement d’un liquide dans une éprouvette graduée (ISO 8130-16:2022)
Le présent document spécifie une méthode de détermination de la masse volumique de poudres pour revêtement, par déplacement d’un liquide dans une éprouvette graduée. Cette méthode repose sur la détermination de la masse et du volume d’une prise d’essai. Elle peut être utilisée pour tous les types de poudres pour revêtement.
NOTE Si la poudre ne gonfle pas au contact du liquide auxiliaire utilisé et si ce liquide remplace l’air qui se trouve entre les particules de poudre, la méthode peut être utilisée et comparée à celle décrite dans l’ISO 8130-3.
Praškasti premazi - 16. del: Določanje gostote z izpodrivom tekočine v merilnem valju (ISO 8130-16:2022)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 8130-16:2023
01-maj-2023
Praškasti premazi - 16. del: Določanje gostote z izpodrivom tekočine v merilnem
valju (ISO 8130-16:2022)
Coating powders - Part 16: Determination of density by liquid displacement in a
measuring cylinder (ISO 8130-16:2022)
Pulverlacke - Teil 16: Bestimmung der Dichte mittels Flüssigkeiteverdrängung in einem
Messzylinder (ISO 8130-16:2022)
Poudres pour revêtement - Partie 16: Titre manque (ISO 8130-16:2022)
Ta slovenski standard je istoveten z: prEN ISO 8130-16
ICS:
87.040 Barve in laki Paints and varnishes
oSIST prEN ISO 8130-16:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 8130-16:2023
---------------------- Page: 2 ----------------------
oSIST prEN ISO 8130-16:2023
INTERNATIONAL ISO
STANDARD 8130-16
First edition
2022-10
Coating powders —
Part 16:
Determination of density by liquid
displacement in a measuring cylinder
Reference number
ISO 8130-16:2022(E)
© ISO 2022
---------------------- Page: 3 ----------------------
oSIST prEN ISO 8130-16:2023
ISO 8130-16:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2022 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 8130-16:2023
ISO 8130-16:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Materials . 1
6 Apparatus . 2
7 Sampling . 2
8 Procedure .2
8.1 Number of determinations and test temperature. 2
8.2 Determination of the density of the displacement liquid . 2
9 Expression of results . 2
10 Precision . 3
11 Test report .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.