EN ISO 10380:2003
(Main)Pipework - Corrugated metal hoses and hose assemblies (ISO 10380:2003)
Pipework - Corrugated metal hoses and hose assemblies (ISO 10380:2003)
ISO 10380:2002 specifies the requirements for the design, manufacture and testing of corrugated metal hoses and hose assemblies for general purposes.
It also specifies sizes from DN 4 to DN 300, pressures from PN 0,5 to PN 250, pressure derating factors for elevated temperatures, two methods of construction and three types of flexibility of hose assembly.
Rohrleitungen - Gewellte Metallschläuche und Metallschlauchleitungen (ISO 10380:2003)
Diese Internationale Norm legt Anforderungen für die Auslegung, Herstellung und Prüfung von gewellten Metallschläuchen und Metallschlauchleitungen für allgemeine Anwendungen fest.
Die Norm legt ferner Nennweiten DN 4 bis DN 300, Drücke PN 0,5 bis PN 250, Druck-Abminderungsfaktoren für erhöhte Temperaturen, zwei Konstruktionsarten und drei Flexibilitätstypen der Schlauchleitung fest.
Tuyauteries - Tuyaux et tuyauteries métalliques flexibles onduleux (ISO 10380:2003)
L'ISO 10380:2002 spécifie les caractéristiques de conception, de construction et d'essai des tuyaux et tuyauteries métalliques flexibles onduleux d'usage général.
L'ISO 10380:2002 spécifie également les diamètres nominaux de DN 4 à DN 300, les pressions nominales de PN 0,5 à PN 250, les facteurs de correction en fonction de la pression pour les températures élevées, deux types de construction et trois types de flexibilité des tuyauteries.
Cevovod - Valovite kovinske cevi in cevni priključki (ISO 10380:2003)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2004
&HYRYRG9DORYLWHNRYLQVNHFHYLLQFHYQLSULNOMXþNL ,62
Pipework - Corrugated metal hoses and hose assemblies (ISO 10380:2003)
Rohrleitungen - Gewellte Metallschläuche und Metallschlauchleitungen (ISO
10380:2003)
Tuyauteries - Tuyaux et tuyauteries métalliques flexibles onduleux (ISO 10380:2003)
Ta slovenski standard je istoveten z: EN ISO 10380:2003
ICS:
23.040.10 Železne in jeklene cevi Iron and steel pipes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 10380
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2003
ICS 23.040.70
English version
Pipework - Corrugated metal hoses and hose assemblies (ISO
10380:2003)
Tuyauteries - Tuyaux et tuyauteries métalliques flexibles Rohrleitungen - Gewellte Metallschläuche und
onduleux (ISO 10380:2003) Metallschlauchleitungen (ISO 10380:2003)
This European Standard was approved by CEN on 9 January 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10380:2003 E
worldwide for CEN national Members.
CORRECTED 2003-03-26
Foreword
This document (EN ISO 10380:2003) has been prepared by Technical Committee ISO/TC 5 "Ferrous
metal pipes and metallic fittings" in collaboration with Technical Committee CEN/TC 342 "Metal hoses,
hose assemblies, bellows and expansion joints", the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2003, and conflicting national standards shall
be withdrawn at the latest by August 2003.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg,
Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 10380:2003 has been approved by CEN as EN ISO 10380:2003 without any
modifications.
INTERNATIONAL ISO
STANDARD 10380
Second edition
2003-02-01
Pipework — Corrugated metal hoses and
hose assemblies
Tuyauteries — Tuyaux et tuyauteries métalliques flexibles onduleux
Reference number
ISO 10380:2003(E)
©
ISO 2003
ISO 10380:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2003 — All rights reserved
ISO 10380:2003(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 1
4 Information to be supplied by the purchaser.2
5 Requirements . 2
5.1 Materials. 2
5.2 Hose dimensions . 4
5.3 Design . 5
5.4 Flexibility and pliability. 6
5.5 Hose manufacture. 7
5.6 Hose joining. 7
5.7 Braid . 8
5.8 Assembly . 8
6 Type tests . 8
6.1 General. 8
6.2 Pliable test . 9
6.3 Cyclic tests . 9
6.4 Pressure test . 12
7 Production tests. 12
7.1 General. 12
7.2 Pressure proof test . 12
7.3 Leakage test . 13
7.4 Cleaning . 13
8 Designation. 13
9 Marking . 13
10 Instructions. 13
Annex A (normative) Equivalent European standards . 14
ISO 10380:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10380 was prepared by Technical Committee ISO/TC 5, Ferrous metal pipes and metallic fittings,
Subcommittee SC 11, Flexible metallic hoses and expansion joints.
This second edition cancels and replaces the first edition (ISO 10380:1994), which has been technically
revised.
iv © ISO 2003 — All rights reserved
ISO 10380:2003(E)
Introduction
It was decided to produce an International Standard under the Vienna Agreement on technical cooperation
between ISO and the European Committee for Standardization (CEN) in order to maintain one document. The
opportunity was taken to re-format the document and to add additional information which was not available for
the first edition of ISO 10380.
The major changes to the standard are
introduction of an extra flexibility type;
reduction in the average number of cycles before failure in the cyclic test;
introduction of a cyclic test for hoses in the size range DN 125 to DN 300;
introduction of nickel materials;
increased requirement for information to be supplied by the purchaser;
the temperature derating factors have been modified based on values in ISO 9328-5;
introduction of the requirement for the provision of adequate user instructions;
the addition of equivalent European standards including those for materials and the corresponding
temperature derating factors which are given in Annex A.
This International Standard is a base standard for hose and hose assemblies for general purposes. Other
International Standards for specific applications are in preparation.
INTERNATIONAL STANDARD ISO 10380:2003(E)
Pipework — Corrugated metal hoses and hose assemblies
1 Scope
This International Standard specifies the requirements for the design, manufacture and testing of corrugated
metal hoses and hose assemblies for general purposes.
It also specifies sizes from DN 4 to DN 300, pressures from PN 0,5 to PN 250, pressure derating factors for
elevated temperatures, two methods of construction and three types of flexibility of hose assembly.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 6208, Nickel and nickel alloy plate, sheet and strip
ISO 7369, Pipework — Metal hoses and hose assemblies — Vocabulary
ISO 9328-5, Steel plates and strips for pressure purposes — Technical delivery conditions — Part 5:
Austenitic steels
ISO 9723, Nickel and nickel alloy bars
ISO 9724, Nickel and nickel alloy wire and drawing stock
ISO 10806, Pipework — Fittings for corrugated metallic hoses
EN 287-1, Approval testing of welders — Fusion welding — Part 1: Steels
EN 288-1, Specification and qualification of welding procedures for metallic materials — Part 1: General rules
for fusion welding
EN 10028-7, Flat products made of steels for pressure purposes — Part 7: Stainless steels
EN 10088-1, Stainless steels — Part 1: List of stainless steels
EN 13133, Brazing — Brazer approval
EN 13134, Brazing — Procedure approval
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 7369 apply.
ISO 10380:2003(E)
4 Information to be supplied by the purchaser
4.1 The purchaser shall state the following in enquiries and orders:
a) intended application;
b) nominal size and hose assembly length;
c) flexibility type;
d) maximum operating pressure;
e) construction method;
f) materials of construction;
g) temperature range;
h) type of fitting for hose assembly.
4.2 Dependent on application, the purchaser shall provide the following information:
a) whether vacuum or any additional testing is required;
b) service cycle life;
c) product to be conveyed;
d) product velocity;
e) any special information concerning choice of materials;
f) whether additional protection is required;
g) movement and/or vibration;
h) any additional requirements for cleaning and post-test treatment;
i) whether “water hammer” can occur;
j) requirements for test certificates;
k) if a coloured cover or other identification is required;
l) any special requirements for packaging.
5 Requirements
5.1 Materials
Materials for the manufacture of corrugated metal hose assemblies shall be selected on the basis of their
suitability for fabrication, e.g. cold forming, welding, etc., and for the conditions under which they will be used
(see 4.1 and 4.2).
A list of suitable materials is given in Table 1.
Alternative equivalent materials are given in Table A.1.
2 © ISO 2003 — All rights reserved
ISO 10380:2003(E)
Table 1 — Materials
a
Materials of Hose Braid
End fittings and ferrules
construction
Stainless steel hose Austenitic stainless steel Austenitic stainless steel in Austenitic stainless steel in
assemblies in accordance with accordance with the accordance with the
ISO 9328–5, types composition given in composition given in
ISO 9328-5, types ISO 9328-5, types
X 2 CrNi 18 10,
X 6 CrNiTi 18 10, X 2 CrNi 18 10, X 2 CrNi 18 10,
X 2 CrNiMo 17 12, X 5 CrNi 18 9, X 5 CrNi 18 9,
X 5 CrNiMo 17 12 and X 6 CrNiTi 18 10, X 6 CrNiTi 18 10,
X 6 CrNiMoTi 17 12 X 2 CrNiMo 17 12, X 2 CrNiMo 17 12,
X 5 CrNiMo 17 12 and X 5 CrNiMo 17 12 and
X 6 CrNiMoTi 17 12 X 6 CrNiMoTi 17 12
Carbon steel containing a
maximum of 0,05 % sulfur and
b
0,05 % phosphorus .
Copper based alloy, if formed,
deep-drawing quality.
Copper-based alloy Deep-drawing quality Phosphor bronze containing Copper-based alloy, if formed,
hose assemblies phosphor bronze a minimum of 95 % copper deep-drawing quality.
containing a minimum of and 1 % tin.
95 % copper and 1 % tin.
Nickel alloy hose Nickel alloy strip in Austenitic stainless steel in Austenitic stainless steel in
assemblies accordance with accordance with the accordance with the
ISO 6208, Nos. composition given in composition given in
ISO 9328-5, types ISO 9328-5 types
NW 0276
NW 4400 X 2 CrNi 18 10, X 2 CrNi 18 10,
NW 6600 X 5 CrNi 18 9, X 5 CrNi 18 9,
NW 6625 X 6 CrNiTi 18 10, X 6 CrNiTi 18 10,
NW 8800 and X 2 CrNiMo 17 12, X 2 CrNiMo 17 12,
NW 8825 X 5 CrNiMo 17 12 and X 5 CrNiMo 17 12 and
X 6 CrNiMoTi 17 12 X 6 CrNiMoTi 17 12
Nickel alloy in accordance Nickel alloy in accordance with
with ISO 9724, Nos. ISO 9723, Nos.
NW 0276 NW 0276
NW 4400 NW 4400
NW 6600 NW 6600
NW 6625, NW 6625,
NW 8800 and NW 8800 and
NW 8825 NW 8825
a
The material specified for end fittings applies only to the parts which are welded or brazed to the hose.
b
Carbon steel shall not be used for ferrules.
ISO 10380:2003(E)
5.2 Hose dimensions
5.2.1 Bore
The minimum bore size of the hose shall be at least 98 % of the nominal size DN given in Table 2.
Table 2 — DN sizes and bend radii
Pliable test Cyclic test
Type 1 and 2 Type 3 Type 1 Type 2
DN
Bend radius
mm
4 25 10 100 120
6 25 12 110 140
8 32 16 130 165
10 38 20 150 190
12 45 25 165 210
15 58 25 195 250
20 70 30 225 285
25 85 45 260 325
32 105 60 300 380
40 130 80 340 430
50 160 100 390 490
65 200 115 460 580
80 240 130 660 800
100 290 160 750 1 000
125 350 — 1 000 1 250
150 400 — 1 250 1 550
200 520 — 1 600 2 000
250 620 — 2 000 2 500
300 720 — 2 400 3 000
NOTE The dimensions listed in this table may be used for design purposes. Refer to
manufacturer for confirmation.
4 © ISO 2003 — All rights reserved
ISO 10380:2003(E)
5.2.2 Overall length
+3
The overall length of a hose assembly shall be the length as ordered to
...
Frequently Asked Questions
EN ISO 10380:2003 is a standard published by the European Committee for Standardization (CEN). Its full title is "Pipework - Corrugated metal hoses and hose assemblies (ISO 10380:2003)". This standard covers: ISO 10380:2002 specifies the requirements for the design, manufacture and testing of corrugated metal hoses and hose assemblies for general purposes. It also specifies sizes from DN 4 to DN 300, pressures from PN 0,5 to PN 250, pressure derating factors for elevated temperatures, two methods of construction and three types of flexibility of hose assembly.
ISO 10380:2002 specifies the requirements for the design, manufacture and testing of corrugated metal hoses and hose assemblies for general purposes. It also specifies sizes from DN 4 to DN 300, pressures from PN 0,5 to PN 250, pressure derating factors for elevated temperatures, two methods of construction and three types of flexibility of hose assembly.
EN ISO 10380:2003 is classified under the following ICS (International Classification for Standards) categories: 23.040.70 - Hoses and hose assemblies. The ICS classification helps identify the subject area and facilitates finding related standards.
EN ISO 10380:2003 has the following relationships with other standards: It is inter standard links to EN ISO 10380:2012. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN ISO 10380:2003 is associated with the following European legislation: EU Directives/Regulations: 2008/68/EC, 305/2011, 89/106/EEC, 97/23/EC; Standardization Mandates: M/071, M/131. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
You can purchase EN ISO 10380:2003 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of CEN standards.
The EN ISO 10380:2003 standard provides comprehensive guidelines for the design, manufacture, and testing of corrugated metal hoses and hose assemblies. Covering a wide range of applications, this standard is pertinent for industries requiring reliable piping solutions due to its detailed specifications and robust parameters. The scope of EN ISO 10380:2003 highlights the versatility of corrugated metal hoses, accommodating sizes from DN 4 to DN 300 and pressures ranging from PN 0.5 to PN 250. This extensive range makes it suitable for various general-purpose applications, catering to the diverse needs of the industry. Additionally, it offers pressure derating factors for elevated temperatures, thus enhancing its relevance in high-temperature scenarios where traditional hoses may fail. One of the notable strengths of this standard is its clear outline of two methods of construction and three types of flexibility for hose assemblies. This detailed information enables manufacturers and engineers to select the appropriate configuration based on specific operational requirements, thereby ensuring optimal performance and safety in pipework systems. The emphasis on stringent testing protocols within the standard further contributes to its credibility, assuring users of the quality and durability of corrugated metal hoses and hose assemblies. By adhering to EN ISO 10380:2003, manufacturers can ensure compliance with international benchmarks, fostering trust and reliability in the marketplace. Overall, the EN ISO 10380:2003 standard stands as a critical benchmark for industries utilizing corrugated metal hoses, helping to enhance operational efficiency, safety, and durability across various applications. Its comprehensive scope and focused guidelines make it an essential reference for all stakeholders involved in pipework involving metal hoses.
SIST EN ISO 10380:2004は、一般的用途のための波形金属ホースおよびホースアセンブリの設計、製造、試験に関する要件を規定しています。この標準は、DN 4からDN 300までのサイズ、PN 0.5からPN 250までの圧力範囲を提供し、高温時の圧力降下係数を考慮に入れることで、幅広い用途に対応しています。 EN ISO 10380:2003の強みは、その明確で包括的な要件にあります。具体的には、施工方法が2種類、ホースアセンブリの柔軟性が3種類規定されているため、さまざまな産業での使用に適した柔軟性が確保されています。また、試験方法に関する詳細な指針も含まれており、製品の信頼性や安全性を高めることができます。 この標準は、工程や環境条件が多様な産業分野でも適用可能であり、その関連性は非常に高いです。特に、流体移動における効率性と安全性の確保が求められる現代の産業環境において、EN ISO 10380:2003は重要な役割を果たします。そのため、波形金属ホースおよびホースアセンブリに関わる全ての関係者は、この標準に準拠し、適切な製品の設計・製造を行うことが求められます。 全体として、SIST EN ISO 10380:2004は、波形金属ホース及びホースアセンブリの安全性と性能を確保するための必須の指針を提供しており、産業界におけるその重要性は今後も変わらないと考えられます。
EN ISO 10380:2003 표준은 일반적인 용도를 위한 주름 금속 호스 및 호스 조립품의 설계, 제조 및 테스트에 관한 요구 사항을 명확히 규정하고 있습니다. 이 문서는 DN 4에서 DN 300까지의 다양한 크기를 포함하며, 압력은 PN 0.5에서 PN 250까지 범위를 설정하고 있습니다. 이 표준의 주요 강점 중 하나는 고온 환경에서의 압력 저감 요인을 명시함으로써 사용자가 특정 조건에서의 성능을 정확히 이해하고 적용할 수 있도록 돕는다는 점입니다. 또한, 두 가지의 구조적 방법과 세 가지 유형의 유연성을 제공하여 다양한 산업 요구에 맞춘 솔루션을 제시합니다. 이는 특히 파이프워크 시스템에서의 신뢰성과 안전성을 대폭 향상시킬 수 있는 요소입니다. 따라서 EN ISO 10380:2003 표준은 파이프워크 설계 및 운영에 있어 필수적이며, 사용자로 하여금 품질 높은 호스 시스템을 선택하고 구축할 수 있는 유용한 지침을 제공합니다. 이러한 점에서 이 표준은 주름 금속 호스 및 호스 조립품에 관한 명확한 기준을 제공하며, 동시에 다양한 산업 분야에 적용 가능성을 높이는 자료로 자리잡고 있습니다.
Die Norm EN ISO 10380:2003 befasst sich mit der Konstruktion, Herstellung und Prüfung von gewellten Metall-Schläuchen und Schlauchassemblierungen für allgemeine Anwendungen. Der Umfang dieser Norm ist sowohl umfassend als auch präzise, da sie die wesentlichen Anforderungen an die Funktionalität und Sicherheit dieser Produkte definiert. Ein bemerkenswerter Stärke der Norm ist die Diversität der abgedeckten Größen und Druckstufen. Sie spezifiziert einen Größenbereich von DN 4 bis DN 300 und Druckbereiche von PN 0,5 bis PN 250, was eine breite Anwendung in verschiedenen Industrien ermöglicht. Diese Flexibilität in den Größen und Drücken trägt wesentlich zur Relevanz der Norm in der heutigen Industrie bei, da sie den Bedürfnissen unterschiedlicher Anwendungen gerecht wird. Darüber hinaus berücksichtigt die Norm Faktoren für die Druckabfallberechnung bei erhöhten Temperaturen, was ein wichtiger Aspekt für die Nutzung in verschiedenen Betriebstemperaturbereichen ist. Die zwei festgelegten Konstruktionsmethoden und die drei Arten der Flexibilität von Schlauchassemblierungen bieten den Anwendern zusätzliche Optionen, um maßgeschneiderte Lösungen für spezifische Anwendungen zu finden. Insgesamt ist die EN ISO 10380:2003 eine bedeutende Norm, die einen wertvollen Beitrag zur Sicherheit und Effizienz von gewellten Metall-Schläuchen leistet. Die klaren Anforderungen und Optionen innerhalb der Norm sichern die Qualität und Zuverlässigkeit von Anwendungen, wodurch sie äußerst relevant für Ingenieure und Hersteller im Bereich der Rohrleitungen bleibt.
La norme EN ISO 10380:2003, intitulée "Pipework - Corrugated metal hoses and hose assemblies" (ISO 10380:2003), joue un rôle crucial dans l'industrie des tuyauteries en spécifiant des exigences claires pour la conception, la fabrication et les essais de flexibles métalliques ondulés et des assemblages de tuyaux destinés à des usages généraux. Cette norme est pertinente pour un large éventail d'applications, garantissant que les produits respectent des critères de sécurité et de performance élevés. L'un des points forts de cette norme est sa portée étendue, couvrant des tailles de DN 4 à DN 300 et des pressions allant de PN 0,5 à PN 250. Cela permet aux fabricants et aux utilisateurs de flexibles métalliques ondulés de choisir des configurations adaptées à leurs besoins spécifiques. De plus, les facteurs de déclassement de pression pour des températures élevées sont également inclus, ce qui renforce la sécurité des assemblages sous des conditions d'utilisation variées. En outre, la norme précise deux méthodes de construction ainsi que trois types de flexibilité pour les assemblages de tuyaux, ce qui équilibre à la fois la robustesse et la maniabilité des produits. Cette variabilité est essentielle dans le design de systèmes de tuyauterie où les conditions peuvent être changeantes ou exigeantes. La norme SIST EN ISO 10380:2004, fondée sur l'ISO 10380:2003, assure une harmonisation internationale et démontre son importance dans le secteur du génie civil et mécanique. Grâce à des exigences normalisées, elle facilite l’innovation tout en garantissant un niveau de qualité et de sécurité systématique pour les flexibles métalliques, ce qui est essentiel dans les industries où la fiabilité des tuyauteries est primordiale. En résumé, la norme EN ISO 10380:2003 est d'une grande pertinence pour les professionnels cherchant à s'assurer de la conformité et de la qualité des assemblages de flexibles métalliques, tout en favorisant des pratiques sûres et efficaces dans le domaine de la tuyauterie.
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...