EN ISO 13517:2020
(Main)Metallic powders - Determination of flow rate by means of a calibrated funnel (Gustavsson flowmeter) (ISO 13517:2020)
Metallic powders - Determination of flow rate by means of a calibrated funnel (Gustavsson flowmeter) (ISO 13517:2020)
This document specifies a method for determining the flow rate of metallic powders, including powders for hardmetals and mixes of metallic powders and organic additives such as lubricants, by means of a calibrated funnel (Gustavsson flowmeter).
The method is applicable only to powders which flow freely through the specified test orifice.
Metallpulver - Ermittlung der Durchflussrate mit Hilfe eines kalibrierten Trichters (Gustavsson-Flowmeter) (ISO 13517:2020)
Dieses Dokument legt ein Verfahren zur Ermittlung der Durchflussrate für Metallpulver einschließlich Hartmetallpulver und Gemische aus Metallpulvern mit organischen Zusatzstoffen, z. B. Schmiermitteln, mit Hilfe eines kalibrierten Trichters (Gustavsson Flowmeter) fest.
Dieses Verfahren ist nur auf Pulver anwendbar, die frei durch die festgelegte Ausflussöffnung des Prüftrichters fließen.
Poudres métalliques - Détermination du temps d'écoulement au moyen d'un entonnoir calibré (cône d'écoulement de Gustavsson) (ISO 13517:2020)
Le présent document spécifie une méthode visant à déterminer le temps d'écoulement des poudres métalliques, y compris les poudres pour métaux-durs et les mélanges de poudres métalliques et d'additifs organiques tels que les lubrifiants, au moyen d'un entonnoir calibré (cône d'écoulement de Gustavsson).
Cette méthode s'applique uniquement aux poudres qui s'écoulent librement par l'orifice d'essai spécifié.
Kovinski praški - Ugotavljanje hitrosti pretoka z uporabo kalibriranega lija (merilnik pretoka po Gustavssonu) (ISO 13517:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2020
Nadomešča:
SIST EN ISO 13517:2014
Kovinski praški - Ugotavljanje hitrosti pretoka z uporabo kalibriranega lija
(merilnik pretoka po Gustavssonu) (ISO 13517:2020)
Metallic powders - Determination of flow rate by means of a calibrated funnel
(Gustavsson flowmeter) (ISO 13517:2020)
Metallpulver - Ermittlung der Durchflussrate mit Hilfe eines kalibrierten Trichters
(Gustavsson flowmeter) (ISO 13517:2020)
Poudres métalliques - Détermination du temps d'écoulement au moyen d'un entonnoir
calibré (cône d'écoulement de Gustavsson) (ISO 13517:2020)
Ta slovenski standard je istoveten z: EN ISO 13517:2020
ICS:
77.160 Metalurgija prahov Powder metallurgy
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 13517
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2020
EUROPÄISCHE NORM
ICS 77.160 Supersedes EN ISO 13517:2013
English Version
Metallic powders - Determination of flow rate by means of
a calibrated funnel (Gustavsson flowmeter) (ISO
13517:2020)
Poudres métalliques - Détermination du temps Metallpulver - Ermittlung der Durchflussrate mit Hilfe
d'écoulement au moyen d'un entonnoir calibré (cône eines kalibrierten Trichters (Gustavsson flowmeter)
d'écoulement de Gustavsson) (ISO 13517:2020) (ISO 13517:2020)
This European Standard was approved by CEN on 1 May 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13517:2020 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 13517:2020) has been prepared by Technical Committee ISO/TC 119 "Powder
metallurgy" in collaboration with CCMC.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2020, and conflicting national standards
shall be withdrawn at the latest by November 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 13517:2013.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 13517:2020 has been approved by CEN as EN ISO 13517:2020 without any modification.
INTERNATIONAL ISO
STANDARD 13517
Second edition
2020-04
Metallic powders — Determination
of flow rate by means of a calibrated
funnel (Gustavsson flowmeter)
Poudres métalliques — Détermination du temps d'écoulement au
moyen d'un entonnoir calibré (cône d'écoulement de Gustavsson)
Reference number
ISO 13517:2020(E)
©
ISO 2020
ISO 13517:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
ISO 13517:2020(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 1
6 Calibration of the funnel. 3
6.1 Calibration by the manufacturer of the funnel . 3
6.2 Calibration by the user of the funnel. 3
7 Sampling . 3
8 Procedure. 4
9 Expression of results . 4
10 Precision . 4
11 Test report . 5
Bibliography . 6
ISO 13517:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see
www .iso .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 119, Powder metallurgy, Subcommittee
SC 2, Sampling and testing methods for powders (including powders for hardmetals), in collaboration
with the European Committee for Standardization (CEN) Technical Committee CEN/SS M11, Powder
metallurgy, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna
Agreement).
This second edition cancels and replaces the first edition (ISO 13517:2013), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— tolerance for the funnel angle has been added;
— reference grit has been used instead of Chinese emery grit;
— the mandatory Clauses 2 and 3 (Normative references and Terms and definitions) have been added
and the subsequent clauses have been renumbered.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved
INTERNATIONAL STANDARD ISO 13517:2020(E)
Metallic powders — Determination of flow rate by means
of a calibrated funnel (Gustavsson flowmeter)
1 Scope
This document specifies a method for determining the flow rate of metallic powders, including powders
for hardmetals and mixes of metallic powders and organic additives such as lubricants, by means of a
calibrated funnel (Gustavsson flowmeter).
The method is applicable only to powders which flow freely through the specified test orifice.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
4 Principle
Measurement of the time required for 50 g of a metallic powder to flow through the orifice of a calibrated
funnel of standardized dimensions.
5 Apparatus
5.1 Calibrated funnel, with the dimensions shown in Figure 1 (see Clause 6). The dimensions shown
for the flowmeter funnel, including the orifice, are not to be considered controlling factors. Calibration
with reference grit, as specified in Clause 6, determines the working flow rate of the funnel.
The funnel shall be made of a non-magnetic, corrosion-resistant metallic material with sufficient wall
thickness and hardness to withstand distortion and excessive wear.
5.2 Stand and horizontal vibration-free base, to support the funnel rigidly, e.g. as indicated in
Figure 2.
5.3 Balance, of sufficient capacity, capable of weighing the test portion to an accuracy of ± 0,05 g.
5.4 Timing device, capable of measuring the elapsed time to an accuracy of ± 0,1 s.
1)
5.5 Reference grit, a reference powder used for calibration of the funnel .
1) Material complying with 5.5 can be purchased as “Chinese emery grit”. This information is given for the
convenience of users of this document and does not constitute an endorsement by ISO of the company named above.
Equivalent products may be used if they can be shown to lead to the same results.
ISO 13517:2020(E)
Dimensions in millimetres
NOTE For dimensions with no individual tolerance, refer to ISO 2
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.