Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition

This document specifies technical delivery conditions for flat products of high yield strength alloy special steels. The grades and qualities are given in Tables 1 to 3 (chemical composition) and Tables 4 to 6 (mechanical properties) and are supplied in the quenched and tempered condition.
The steels specified in this document are applicable to hot-rolled flat products with a minimum nominal thickness of 3 mm and a maximum nominal thickness of 200 mm for grades S460, S500, S550, S620 and S690, a maximum nominal thickness of 125 mm for grades S890 and S960, in steels which, after quenching and tempering, have a specified minimum yield strength of 460 MPa to 960 MPa.

Warmgewalzte Erzeugnisse aus Baustählen - Teil 6: Technische Lieferbedingungen für Flacherzeugnisse aus Stählen mit höherer Streckgrenze im vergüteten Zustand

Produits laminés à chaud en aciers de construction - Partie 6 : Conditions techniques de livraison pour produits plats des aciers à haute limite d'élesticité à l'état trempé et revenu

Vroče valjani izdelki iz konstrukcijskih jekel - 6. del: Tehnični dobavni pogoji za ploščate izdelke iz konstrukcijskih jekel z visoko mejo plastičnosti v poboljšanem stanju jekla - Dopolnilo A1

General Information

Status
Not Published
Publication Date
21-Feb-2023
Current Stage
4060 - Closure of enquiry - Enquiry
Start Date
30-Jun-2022
Due Date
02-Dec-2022
Completion Date
30-Jun-2022

Relations

Buy Standard

Draft
EN 10025-6:2019/oprA1:2022
English language
4 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-junij-2022
Vroče valjani izdelki iz konstrukcijskih jekel - 6. del: Tehnični dobavni pogoji za
ploščate izdelke iz konstrukcijskih jekel z visoko mejo plastičnosti v poboljšanem
stanju jekla - Dopolnilo A1
Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat
products of high yield strength structural steels in the quenched and tempered condition
Warmgewalzte Erzeugnisse aus Baustählen - Teil 6: Technische Lieferbedingungen für
Flacherzeugnisse aus Stählen mit höherer Streckgrenze im vergüteten Zustand
Produits laminés à chaud en aciers de construction - Partie 6 : Conditions techniques de
livraison pour produits plats des aciers à haute limite d'élesticité à l'état trempé et revenu
Ta slovenski standard je istoveten z: EN 10025-6:2019/prA1
ICS:
77.140.10 Jekla za toplotno obdelavo Heat-treatable steels
77.140.50 Ploščati jekleni izdelki in Flat steel products and semi-
polizdelki products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
EN 10025-6:2019
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
April 2022
ICS 77.140.10; 77.140.50
English Version
Hot rolled products of structural steels - Part 6: Technical
delivery conditions for flat products of high yield strength
structural steels in the quenched and tempered condition
Produits laminés à chaud en aciers de construction - Warmgewalzte Erzeugnisse aus Baustählen - Teil 6:
Partie 6 : Conditions techniques de livraison pour Technische Lieferbedingungen für Flacherzeugnisse
produits plats des aciers à haute limite d'élesticité à aus Stählen mit höherer Streckgrenze im vergüteten
l'état trempé et revenu Zustand
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC
459/SC 3.
This draft amendment A1, if approved, will modify the European Standard EN 10025-6:2019. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Polan
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.