FprEN 10025-1
(Main)Hot rolled products of structural steels - Part 1: General (Characteristics, evaluation of conformity and marking)
Hot rolled products of structural steels - Part 1: General (Characteristics, evaluation of conformity and marking)
This document specifies product characteristics, test methods and performance criteria for flat (plates, strips, sheets, wide flats) and long (sections, bars, rod) products of hot rolled structural steels excluding structural hollow sections and tubes.
The steels specified in this document are intended for use in welded, bolted and riveted structures.
This document does not apply to coated products.
Warmgewalzte Erzeugnisse aus Baustählen - Teil 1: Allgemeines
1.1 Dieses Dokument legt Anforderungen fest für Flach- und Langerzeugnisse (siehe Abschnitt 3) aus warmgewalzten Baustählen, mit Ausnahme von Hohlprofilen und Rohren. Teil 1 dieses Dokumentes legt die allgemeinen Lieferbedingungen fest.
Die spezifischen Anforderungen an Baustähle sind in den folgenden Teilen enthalten:
Teil 2: Technische Lieferbedingungen für unlegierte Baustähle
Teil 3: Technische Lieferbedingungen für normalgeglühte/normalisierend gewalzte schweißgeeignete Fein-kornbaustähle
Teil 4: Technische Lieferbedingungen für thermomechanisch gewalzte schweißgeeignete Feinkornbaustähle
Teil 5: Technische Lieferbedingungen für wetterfeste Baustähle
Teil 6: Technische Lieferbedingungen für Flacherzeugnisse aus Stählen mit höherer Streckgrenze im ver- güteten Zustand
Die Stähle nach diesem Dokument sind für die Verwendung in geschweißten, geschraubten und genieteten Bauteilen bestimmt.
1.2 Dieses Dokument gilt nicht für Erzeugnisse mit Überzügen sowie nicht für Erzeugnisse aus Stählen für den allgemeinen Stahlbau nach den in den Literaturhinweisen enthaltenen Normen und Norm-Entwürfen.
Produits laminés à chaud en aciers de construction - Partie 1 : Générales
Le présent document spécifie les exigences pour les produits longs et plats (voir Article 3) en aciers
de construction laminés à chaud, à l’exclusion des profils creux de construction et des tubes. La partie 1 de la
présente Norme européenne spécifie les conditions générales de livraison.
Les exigences spécifiques pour les aciers de construction sont données dans les parties suivantes :
¾ partie 2 : Conditions techniques de livraison des aciers de construction non alliés ;
¾ partie 3 : Conditions techniques de livraison des aciers de construction soudables à grains fins à l’état
normalisé/laminage normalisant ;
¾ partie 4 : Conditions techniques de livraison des aciers de construction soudables à grains fins obtenus
par laminage thermomécanique ;
¾ partie 5 : Conditions techniques de livraison des aciers de construction à résistance améliorée à la
corrosion atmosphérique ;
¾ partie 6 : Conditions techniques de livraison des produits plats en aciers de construction à haute limite
d’élasticité à l’état trempé et revenu.
Les aciers spécifiés dans le présent document sont destinés à la fabrication d'éléments de construction
soudés ou assemblés par rivets ou boulons.
1.2 Le présent document ne s'applique pas aux produits revêtus et aux produits en acier d'usage général
qui sont conformes aux normes et projets de normes, et dont la liste figure dans la bibliographie.
Vroče valjani izdelki iz konstrukcijskih jekel - 1. del: Splošno
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2014
9URþHYDOMDQLL]GHONLL]NRQVWUXNFLMVNLKMHNHOGHO 6SORãQR
Hot rolled products of structural steels - Part 1: General
Warmgewalzte Erzeugnisse aus Baustählen - Teil 1: Allgemeines
Produits laminés à chaud en aciers de construction - Partie 1 : Générales
Ta slovenski standard je istoveten z: prEN 10025-1
ICS:
77.140.10 Jekla za toplotno obdelavo Heat-treatable steels
77.140.50 3ORãþDWLMHNOHQLL]GHONLLQ Flat steel products and semi-
SROL]GHONL products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
WHITE DRAFT
prEN 10025-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2014
ICS 77.140.10; 77.140.50 Will supersede EN 10025-1:2004
English Version
Hot rolled products of structural steels - Part 1: General
Produits laminés à chaud en aciers de construction - Partie Warmgewalzte Erzeugnisse aus Baustählen - Teil 1:
1 : Générales Allgemeines
This draft European Standard is submitted to ECISS/COCOR before submission to CEN members for formal vote. It has been drawn up by
the Technical Committee ECISS/TC 103.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 10025-1:2014 E
worldwide for CEN national Members.
prEN 10025-1:2014 (E)
Contents
Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Terms and definitions .5
4 Product characteristics .5
4.1 General .5
4.2 Dimensions, tolerances on dimensions and shape .6
4.3 Mechanical properties (yield strength, tensile strength, elongation and impact strength) .6
4.4 Weldability .6
4.5 Durability (chemical composition) .6
4.6 Dangerous substances .6
5 Testing, assessment and sampling methods .7
5.1 Tolerances on dimensions and shape .7
5.2 Mechanical properties .7
5.3 Chemical composition (durability, weldability) .9
6 Assessment and verification of constancy of performance .9
6.1 General .9
6.2 Type testing .9
6.3 Factory production control (FPC) . 11
7 Classification and designation . 15
7.1 Grades and qualities . 15
7.2 Designation . 15
8 Marking, labelling and packaging . 15
Annex A (normative) Location of samples and test pieces . 16
Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU
Construction Products Regulation . 19
Bibliography . 26
prEN 10025-1:2014 (E)
Foreword
This document (prEN 10025-1:2014) has been prepared by Technical Committee ECISS/TC 103 “Structural
steels other then reinforcements”, the secretariat of which is held by DIN.
This document is currently submitted to the COCOR Vote.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s)/EU Regulation(s).
For relationship with EU Directive(s)/EU Regulation(s), see informative Annex ZA, which is an integral part of
this document.
This document will supersede EN 10025-1:2004.
The main changes with respect to the previous edition are listed below:
document completely revised taking into account requirements of the Regulation (EU) 305/2011.
EN 10025 consists of the following parts:
Part 1: General
Part 2: Technical delivery conditions for non-alloy structural steels
Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance
Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched
and tempered condition
prEN 10025-1:2014 (E)
1 Scope
This document specifies product characteristics, test methods and performance criteria for flat (plates, strips,
sheets, wide flats) and long (sections, bars, rod) products of hot rolled structural steels excluding structural
hollow sections and tubes.
The steels specified in this document are intended for use in welded, bolted and riveted structures.
This document does not apply to coated products.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
2.1 General standards
EN 10020:2000, Definition and classification of grades of steel
prEN 10025-2:2014, Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy
structural steels
prEN 10025-3:2014, Hot rolled products of structural steels - Part 3: Technical delivery conditions for
normalized/normalized rolled weldable fine grain structural steels
prEN 10025-4:2014, Hot rolled products of structural steels - Part 4: Technical delivery conditions for
thermomechanical rolled weldable fine grain structural steels
prEN 10025-5:2014, Hot rolled products of structural steels - Part 5: Technical delivery conditions for
structural steels with improved atmospheric corrosion resistance
prEN 10025-6:2014, Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat
products of high yield strength structural steels in the quenched and tempered condition
EN 10027-1, Designation systems for steels - Part 1: Steel names
EN 10027-2, Designation systems for steels - Part 2: Numerical system
EN 10079:2007, Definition of steel products
2.2 Standards on dimensions and tolerances (see 4.2)
EN 10017, Steel rod for drawing and/or cold rolling - Dimensions and tolerances
EN 10024, Hot rolled taper flange I sections - Tolerances on shape and dimensions
EN 10029, Hot rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape
EN 10034, Structural steel I and H sections - Tolerances on shape and dimensions
EN 10048, Hot rolled narrow steel strip - Tolerances on dimensions and shape
EN 10051, Continuously hot-rolled uncoated plate, sheet and strip of non-alloy and alloy steels - Tolerances
on dimensions and shape
EN 10055, Hot-rolled steel equal flange tees with radiused root and toes - Dimensions and tolerances on
shape and dimensions
prEN 10025-1:2014 (E)
EN 10056-1, Structural steel equal and unequal leg angles - Part 1: Dimensions
EN 10056-2, Structural steel equal and unequal leg angles - Part 2: Tolerances on shape and dimensions
EN 10058, Hot rolled flat steel bars for general purposes - Dimensions and tolerances on shape and
dimensions
EN 10059, Hot rolled square steel bars for general purposes - Dimensions and tolerances on shape and
dimensions
EN 10060, Hot rolled round steel bars - Dimensions and tolerances on shape and dimensions
EN 10061, Hot rolled hexagon steel bars - Dimensions and tolerances on shape and dimensions
EN 10067, Hot rolled bulb flats - Dimensions and tolerances on shape, dimensions and mass
EN 10279, Hot rolled steel channels - Tolerances on shape, dimensions and mass
2.3 Standards on testing
EN 10315, Routine method for analysis of high alloy steel by X-ray Fluorescence Spectrometry (XRF) by
using a near by technique
CEN/CR 10320, Optical emission analysis of low alloy steels (routine method) – Method for determination of
C, Si, S, P, Mn, Cr, Ni and Cu
EN ISO 148-1, Metallic materials – Charpy pendulum impact test – Part 1: Test method (ISO 148-1:2009)
EN ISO 377, Steel and steel products - Location and preparation of samples and test pieces for mechanical
testing (ISO 377:2013)
EN ISO 2566-1, Steel - Conversion of elongation values - Part 1: Carbon and low alloy steels (ISO 2566-
1:1984)
EN ISO 6892-1:2009, Metallic materials – Tensile testing – Part 1: Method of testing at room temperature
(ISO 6892-1:2009)
EN ISO 14284, Steel and iron - Sampling and preparation of samples for the determination of chemical
composition (ISO 14284:1996)
EN ISO 15350, Steel and iron – Determination of total carbon and sulphur content – Infrared absorption
method after combustion in an induction furnace (routine method) (ISO 15350:2000)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 10079:2007 and the following apply:
3.1 product range
means group of products produced by one manufacturer for which the test results for one or more
characteristics from any one product within the range are valid for all other products within this range
4 Product characteristics
4.1 General
The following product characteristics apply when sampling, preparation of test pieces and testing specified in
Clauses 5 are carried out.
prEN 10025-1:2014 (E)
4.2 Dimensions, tolerances on dimensions and shape
Dimensions, tolerances on dimensions and shape shall be in accordance with the requirements given in the
relevant documents according to 2.2.
Dimensions, tolerances on dimensions and shape of profiles not covered by a document or hot rolled
patterned plates shall be in accordance with a national standard valid in the intended place of use of the
product.
4.3 Mechanical properties (yield strength, tensile strength, elongation and impact strength)
4.3.1 General
Under the inspection and testing conditions as specified in Clauses 5 the yield strength, the tensile strength,
the elongation and the impact strength shall comply with the relevant requirements specified in prEN 10025-2
to prEN 10025-6.
4.3.2 Impact strength
Using test pieces of width less than 10 mm the minimum values given in prEN 10025-2 to
prEN 10025-6 shall be reduced in direct proportion to the cross-sectional area of the test piece.
Impact tests shall not be required for:
nominal thickness < 6 mm for flat products and sections,
nominal diameter < 16 mm for products with round cross-section,
nominal thickness < 12 mm for bars
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.