Conveyor belts for general purpose use - Electrical and flammability safety requirements

This document specifies electrical and flammability safety requirements for general purpose conveyor belts not intended for use in underground installations and a means of categorizing conveyor belts in terms of the level of safety sought in their end use application. This document does not provide electrical safety requirements for volume resistance which may be measured by the methods in EN ISO 21178 and which is relevant to some types of light conveyor belts.
This document is not applicable to conveyor belts which are manufactured before the date of publication of this document by CEN.
NOTE 1   Directive 94/9/EC concerning equipment and protective systems intended for use in potentially explosive atmospheres can be applicable to the type of machine or equipment covered by this document. The present standard is not intended to provide means of complying with the essential health and safety requirements of Directive 94/9/EC, this being covered in EN 14973.
NOTE 2   prEN 12882 is not a product standard but is intended to help users of conveyor belts to select the required electrical and flammability safety properties needed following a suitable risk assessment. No requirements are, therefore, included for marking, information to be supplied, etc., these matters being covered in relevant product standards such as EN ISO 14890 and EN ISO 1523-1.

Fördergurte für allgemeine Anwendung - Elektrische und brandtechnische Sicherheitsanforderungen

Dieses Dokument legt elektrische und brandtechnische Anforderungen an Fördergurte für allgemeine Anwendung fest, die nicht für den Einsatz unter Tage vorgesehen sind, sowie die Klassifizierung von Fördergurten hinsichtlich des für den Verwendungszweck angestrebten Sicherheitsgrads. In diesem Dokument sind keine Sicherheitsanforderungen an den elektrischen Durchgangswiderstand festgelegt, der mit den in EN ISO 21178 genannten Verfahren gemessen werden kann und der für einige Typen leichter Fördergurte von Bedeutung ist.
Dieses Dokument gilt nicht für Fördergurte, die vor dem Datum der Veröffentlichung dieses Dokuments durch CEN hergestellt wurden.
ANMERKUNG 1   Richtlinie 94/9/EG, die Einrichtungen und Schutzsysteme für den Einsatz in potentiell explosiven Atmosphären betrifft, kann für den Maschinentyp oder Einrichtungen zutreffen, die durch dieses Dokument abgedeckt sind. Die vorliegende Norm ist nicht zur Erfüllung der wesentlichen Gesundheits- und Sicherheitsanforderungen der Richtlinie 94/9/EG vorgesehen, die durch EN 14973 abgedeckt ist.
ANMERKUNG 2   prEN 12882 ist keine Produktnorm, sondern dazu gedacht, den Anwendern von Fördergurten bei der Auswahl der erforderlichen elektrischen und brandtechnischen sicherheitsrelevanten Eigenschaften zu helfen, die aufgrund einer angemessenen Risikobeurteilung notwendig sind. Deshalb sind keine Anforderungen an Kennzeichnung, bereitzustellende Angaben usw. enthalten, da diese Themen durch die entsprechenden Produktnormen wie beispielsweise EN ISO 14890 und EN ISO 15236 1 abgedeckt sind.

Courroies transporteuses à usage général - Prescriptions de sécurité électrique et protection contre l'inflammabilité

Le présent document spécifie les prescriptions de sécurité électrique et de protection contre l’inflammabilité relatives aux courroies transporteuses à usage général qui ne sont pas destinées à être utilisées dans des installations souterraines, ainsi qu’une méthode de classement des courroies transporteuses en termes de niveau de sécurité recherché dans leur application finale. Le présent document ne fournit pas de prescriptions de sécurité électrique pour la résistance volumique qui peut être mesurée selon les méthodes de l’EN ISO 21178 et qui est pertinente pour certains types de courroies transporteuses légères.
Le présent document ne s’applique pas aux courroies transporteuses fabriquées avant la date de publication du présent document par le CEN.
NOTE 1   La Directive 94/9/CE concernant les appareils et les systèmes de protection destinés à être utilisés en atmosphères explosibles peut être applicable au type de machine ou d’appareil couvert par le présent document. La présente norme n’est pas destinée à fournir un moyen de se conformer aux exigences essentielles en matière de santé et de sécurité de la Directive 94/9/CE, cet aspect étant traité dans l’EN 14973.
NOTE 2   Le prEN 12882 n’est pas une norme de produit, mais est prévue pour aider les utilisateurs de courroies transporteuses à choisir les propriétés de sécurité électrique et de protection contre l’inflammabilité requises après une évaluation appropriée des risques. Aucune prescription n’est donc incluse pour le marquage, les informations à fournir, etc., ces sujets étant couverts par les normes de produits pertinentes telles que l’EN ISO 14890 et l’EN ISO 15236-1.

Naprave za kontinuirni transport - Trakovi tračnih transporterjev za splošne namene - Električne in požarnovarnostne zahteve

General Information

Status
Not Published
Publication Date
02-Jun-2025
Current Stage
4020 - Submission to enquiry - Enquiry
Start Date
26-Sep-2024
Due Date
16-Jan-2024
Completion Date
26-Sep-2024

Relations

Buy Standard

Draft
prEN 12882:2024
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-november-2024
Naprave za kontinuirni transport - Trakovi tračnih transporterjev za splošne
namene - Električne in požarnovarnostne zahteve
Conveyor belts for general purpose use - Electrical and flammability safety requirements
Fördergurte für allgemeine Anwendung - Elektrische und brandtechnische
Sicherheitsanforderungen
Courroies transporteuses à usage général - Prescriptions de sécurité électrique et
protection contre l'inflammabilité
Ta slovenski standard je istoveten z: prEN 12882
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
53.040.20 Deli za transporterje Components for conveyors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2024
ICS 53.040.20 Will supersede EN 12882:2015
English Version
Conveyor belts for general purpose use - Electrical and
flammability safety requirements
Courroies transporteuses à usage général - Fördergurte für allgemeine Anwendung - Elektrische
Prescriptions de sécurité électrique et protection und brandtechnische Sicherheitsanforderungen
contre l'inflammabilité
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 188.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12882:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Safety requirements . 6
4.1 General. 6
4.2 Electrical conductivity . 6
4.3 Flame retardation . 7
4.4 Fire simulation . 7
4.5 Drum friction . 7
5 Safety categories . 8
5.1 Category 1 . 8
5.2 Category 2A . 8
5.3 Category 2B . 8
5.4 Category 3A . 8
5.5 Category 3B . 8
5.6 Category 4A . 9
5.7 Category 4B . 9
5.8 Category 5A . 9
5.9 Category 5B . 9
5.10 Category 5C . 9
6 Test reports for conveyor belts used in aboveground installations . 10
Annex A (informative) Suggested belt approval / certification options . 12
A.1 Construction series of steel cord conveyor belts . 12
A.2 Construction series of single or double ply textile conveyor belts . 12
A.3 Construction series of multi-layer textile conveyor belts . 13
Annex ZA (informative)  Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered . 15
Annex ZB (informative) Relationship between this European Standard and the essential
requirements of Regulation (EU) 2023/1230 aimed to be covered . 16
Bibliography . 17

European foreword
This document (prEN 12882:2024) has been prepared by Technical Committee CEN/TC 188 “Conveyor
belts”, the secretariat of which is held by SNV.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 12882:2015.
This document includes the following significant technical changes with respect to EN 12882:2015:
— The EN ISO 20238 procedures have been revised for categories 3A, 3B, 4B, 5A, 5B and 5C;
— A new Clause 6 "Test reports for conveyor belts for use above ground" has been added;
— The definition of the type series has been revised and described in detail.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this
document.
Introduction
This document is a type C standard as stated in EN ISO 12100:2010.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered
are indicated in the scope of this document.
When provisions of this type C standard are different from those which are stated in type A or B
standards, the provisions of this type C standard take precedence over the provisions of the other
standards, for machines that have been designed and built according to the provisions of this type C
standard.
During the preparation of this document, the hazards which have been identified as being directly related
to the use of conveyor belts are:
a) hazards associated with the discharge of static electrical energy;
b) hazards associated with the impingement of small naked flames on the cover and/or carcass of a
conveyor belt at rest;
c) hazards caused by the stalling of a conveyor belt and the continued operation of the driving
mechanism causing localized heating of the conveyor belt through contact with the driving drum or
cylinder or some other source of frictional heat;
d) hazards caused by the propagation of a flame along a belt which has been exposed to a relatively high
energy source such as a fire.
The risk, or probable rate of occurrence of these hazards and the degree of harm they can cause will vary
depending upon the particular circumstances of the application or site of application, which are many
and varied. Consequently, the level of safety required will vary from one application to another,
depending upon the risks judged to be pertinent. The hazards listed above should not be taken as the only
properties affecting safety in operation. Other aspects such as health or environmental requirements
should be considered. Depending on the individual end use requirement, these other factors can affect
the category of belt selected and additional safety precautions may need to be employed.
This document is therefore designed to enable the user to select the category of conveyor belt most suited
to the particular circumstances of the application.
1 Scope
This document specifies electrical and flammability safety requirements for general purpose conveyor
belts not intended for use in underground installations and a means of categorizing conveyor belts in
terms of the level of safety sought in their end use application. This document does not provide electrical
safety requirements for volume resistance which may be measured by the methods in EN ISO 21178 and
which is relevant to some types of light conveyor belts.
This document is not applicable to conveyor belts which are manufactured before the date of publication
of this document by CEN.
NOTE 1 Directive 94/9/EC concerning equipment and protective systems intended for use in potentially
explosive atmospheres can be applicable to the type of machine or equipment covered by this document. The
present standard is not intended to provide means of complying with the essential health and safety requirements
of Directive 94/9/EC, this being covered in EN 14973.
NOTE 2 prEN 12882 is not a product standard but is intended to help users of conveyor belts to select the
required electrical and flammability safety properties needed following a suitable risk assessment. No requirements
are, therefore, included for marking, information to be supplied, etc., these matters being covered in relevant
product standards such as EN ISO 14890 and EN ISO 15236-1.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 12881-1:2014, Conveyor belts - Fire simulation flammability testing - Part 1: Propane burner tests
EN ISO 284:2012, Conveyor belts - Electrical conductivity - Specification and test method (ISO 284:2012)
EN ISO 340:2022, Conveyor belts - Laboratory scale flammability characteristics - Requirements and test
method (ISO 340:2022)
EN ISO 21178:2020, Light conveyor belts - Determination of electrical resistances (ISO 21178)
EN ISO 21179:2013, Light conveyor belts - Determination of the electrostatic field generated by a running
light conveyor belt (ISO 21179:2013)
EN ISO 21183-1:2006, Light conveyor belts - Part 1: Principal characteristics and applications (ISO 21183-
1:2005)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/
— IEC Electropedia: available at https://www.electropedia.org/
3.1
afterflame
flame which persists after the ignition source has been removed
3.2
afterglow
persistence of glowing, after cessation of flaming or, if no flaming occurs, after the ignition source has
been removed
3.3
flame
zone of combustion in the gaseous phase usually with emission of light
3.4
flame
to undergo combustion in the gaseous phase with emission of light
3.5
glowing
made luminous by heat, (without flame)
3.6
undamaged
part remaining of a conveyor belt after the termination of the propane gallery fire test, described in
accordance with EN 12881-1:2014, and which shows no evidence of embrittlement, cracking, blistering
or other blemis
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.