EN ISO 283:2023
(Main)Textile conveyor belts - Full thickness tensile strength, elongation at break and elongation at the reference load - Test method (ISO 283:2023)
Textile conveyor belts - Full thickness tensile strength, elongation at break and elongation at the reference load - Test method (ISO 283:2023)
This document specifies a test method for the determination of the full thickness tensile strength in the longitudinal direction and the elongation at the reference force and breaking point of conveyor belts having a textile carcass. The method can also be used for the determination of full thickness tensile strength in the transverse direction and the elongation at the breaking point, for use when the manufacturer is requested by the purchaser to state values for these properties.
This document does not apply to light conveyor belts as described in ISO 21183‑1.
Textilfördergurte - Zugfestigkeit bei voller Gurtdicke, Bruchdehnung und Dehnung bei Bezugslast - Prüfverfahren (ISO 283:2023)
Dieses Dokument legt ein Prüfverfahren zur Bestimmung der Zugfestigkeit bei voller Gurtdicke in Längsrichtung und der Dehnung bei Bezugskraft und der Bruchstelle von Fördergurten mit einer Textilkarkasse fest. Außerdem legt sie ein Verfahren zur Bestimmung der Zugfestigkeit bei voller Gurtdicke in Querrichtung und die Bruchdehnung fest, für den Fall, dass der Käufer den Hersteller auffordert, Werte für den Gebrauch vorzulegen.
Dieses Dokument ist nicht anwendbar auf die in ISO 21183 1 beschriebenen leichten Fördergurte.
Courroies transporteuses à carcasse textile - Résistance à la traction, allongement à la rupture et allongement sous force de référence en pleine épaisseur - Méthode d'essai (ISO 283:2023)
Le présent document spécifie une méthode d’essai pour la détermination de la résistance à la traction dans le sens longitudinal et l’allongement sous force de référence et au point de rupture des courroies transporteuses à carcasse textile en pleine épaisseur. La méthode peut également être utilisée pour la détermination de la résistance à la traction dans le sens transversal et de l’allongement au point de rupture en pleine épaisseur, pour une utilisation lorsque l’acheteur demande au fabricant de déclarer les valeurs de ces propriétés.
Le présent document n’est pas applicable pour les courroies transporteuses légères décrites dans l’ISO 21183‑1.
Naprave za kontinuirni transport - Trakovi tračnih transporterjev - Natezna trdnost pri polni debelini traku, raztezek pri porušitvi in raztezek pri referenčni sili - Preskusna metoda (ISO 283:2023)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 283:2023
01-september-2023
Naprave za kontinuirni transport - Trakovi tračnih transporterjev - Natezna trdnost
pri polni debelini traku, raztezek pri porušitvi in raztezek pri referenčni sili -
Preskusna metoda (ISO 283:2023)
Textile conveyor belts - Full thickness tensile strength, elongation at break and
elongation at the reference load - Test method (ISO 283:2023)
Textilfördergurte – Zugfestigkeit bei voller Gurtdicke, Bruchdehnung und Dehnung bei
breitenbezogener Bruchkraft – Prüfverfahren (ISO 283:2023)
Courroies transporteuses à carcasse textile - Résistance à la traction, allongement à la
rupture et allongement sous force de référence en pleine épaisseur - Méthode d'essai
(ISO 283:2023)
Ta slovenski standard je istoveten z: EN ISO 283:2023
ICS:
53.040.20 Deli za transporterje Components for conveyors
SIST EN ISO 283:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 283:2023
---------------------- Page: 2 ----------------------
SIST EN ISO 283:2023
EN ISO 283
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2023
EUROPÄISCHE NORM
ICS 53.040.20 Supersedes EN ISO 283:2015
English Version
Textile conveyor belts - Full thickness tensile strength,
elongation at break and elongation at the reference load -
Test method (ISO 283:2023)
Courroies transporteuses à carcasse textile - Textilfördergurte - Zugfestigkeit bei voller Gurtdicke,
Résistance à la traction, allongement à la rupture et Bruchdehnung und Dehnung bei breitenbezogener
allongement sous force de référence en pleine Bruchkraft - Prüfverfahren (ISO 283:2023)
épaisseur - Méthode d'essai (ISO 283:2023)
This European Standard was approved by CEN on 1 March 2023.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 283:2023 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 283:2023
EN ISO 283:2023 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 283:2023
EN ISO 283:2023 (E)
European foreword
This document (EN ISO 283:2023) has been prepared by Technical Committee ISO/TC 41 "Pulleys and
belts (including veebelts)" in collaboration with Technical Committee CEN/TC 188 “Conveyor belts” the
secretariat of which is held by SNV.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2023, and conflicting national standards shall
be withdrawn at the latest by October 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 283:2015.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 283:2023 has been approved by CEN as EN ISO 283:2023 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 283:2023
---------------------- Page: 6 ----------------------
SIST EN ISO 283:2023
INTERNATIONAL ISO
STANDARD 283
Fifth edition
2023-03
Textile conveyor belts — Full thickness
tensile strength, elongation at break
and elongation at the reference load
— Test method
Courroies transporteuses à carcasse textile — Résistance à la traction,
allongement à la rupture et allongement sous force de référence en
pleine épaisseur — Méthode d'essai
Reference number
ISO 283:2023(E)
© ISO 2023
---------------------- Page: 7 ----------------------
SIST EN ISO 283:2023
ISO 283:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2023 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 283:2023
ISO 283:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
6 Test pieces .3
6.1 Shape and dimensions . 3
6.2 Method of selection of test pieces . 3
6.3 Preparation of test pieces . 7
6.4 Number of test pieces . 7
6.5 Conditioning of test pieces . 8
7 Procedure .8
8 Calculation and expression of results . 8
8.1 Tensile strength . 8
8.2 Elongation . 8
8.2.1 Elongation at break . 8
8.2.2 Elongation at reference force (see 3.5) . 9
9 Test report . 9
Bibliography .10
iii
© ISO 2023 – All rights reserved
---------------------- Page: 9 ----------------------
SIST EN ISO 283:2023
ISO 283:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 41, Pulleys and belts (including veebelts),
Subcommittee SC 3, Conveyor belts, in collaboration with the European Committee for Standardization
(CEN) T
...
SLOVENSKI STANDARD
oSIST prEN ISO 283:2022
01-junij-2022
Naprave za kontinuirni transport - Trakovi tračnih transporterjev - Natezna trdnost
pri polni debelini traku, raztezek pri porušitvi in raztezek pri referenčni sili -
Preskusna metoda (ISO/DIS 283:2022)
Textile conveyor belts - Full thickness tensile strength, elongation at break and
elongation at the reference load - Test method (ISO/DIS 283:2022)
Textilfördergurte – Zugfestigkeit bei voller Gurtdicke, Bruchdehnung und Dehnung bei
breitenbezogener Bruchkraft – Prüfverfahren (ISO/DIS 283:2022)
Courroies transporteuses à carcasse textile - Résistance à la traction, allongement à la
rupture et allongement sous force de référence en pleine épaisseur - Méthode d'essai
(ISO/DIS 283:2022)
Ta slovenski standard je istoveten z: prEN ISO 283
ICS:
53.040.20 Deli za transporterje Components for conveyors
oSIST prEN ISO 283:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 283:2022
---------------------- Page: 2 ----------------------
oSIST prEN ISO 283:2022
DRAFT INTERNATIONAL STANDARD
ISO/DIS 283
ISO/TC 41/SC 3 Secretariat: SAC
Voting begins on: Voting terminates on:
2022-04-22 2022-07-15
Textile conveyor belts — Full thickness tensile strength,
elongation at break and elongation at the reference load —
Test method
Courroies transporteuses à carcasse textile — Résistance à la traction, allongement à la rupture et
allongement sous force de référence en pleine épaisseur — Méthode d'essai
ICS: 53.040.20
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 283:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
---------------------- Page: 3 ----------------------
oSIST prEN ISO 283:2022
ISO/DIS 283:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2022 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 283:2022
ISO/DIS 283:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
6 Test pieces .3
6.1 Shape and dimensions . 3
6.2 Method of selection of test pieces . 3
6.3 Preparation of test pieces . 6
6.4 Number of test pieces . 6
6.5 Conditioning of test pieces . 7
7 Procedure .7
8 Calculation and expression of results . 7
8.1 Tensile strength . 7
8.2 Elongation . 7
8.2.1 Elongation at break . 7
8.2.2 Elongation at reference force (see 3.5) . 8
9 Test report . 8
Bibliography . 9
iii
© ISO 2022 – All rights reserved
---------------------- Page: 5 ----------------------
oSIST prEN ISO 283:2022
ISO/DIS 283:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO's adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.
The committee responsible for this document is ISO/TC 41, Pulleys and belts (including veebelts),
Subcommittee SC 3, Conveyor belts.
This fifth edition cancels and replaces the fourth edition (ISO 283:2015), which has been technically
revised.
iv
© ISO 2022 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 283:2022
DRAFT INTERNATIONAL STANDARD ISO/DIS 283:2022(E)
Textile conveyor belts — Full thickness tensile strength,
elongation at break and elongation at the reference load —
Test method
1 Scope
This International Standard specifies a test method for the determination of the full thickness tensile
strength in the longitudinal direction and the elongation at the reference force and breaking point
of conveyor belts having a textile carcass. The method can also be used for the determination of full
thickness tensile strength in the transverse direction and the elongation at the breaking point, for use
when the manufacturer is requested by the purchaser to state values for these properties.
This International Standard is not suitable or valid for light conveyor belts as described in ISO 21183-1.
2 Normative references
The following documents, in whole or in part, are normatively referenced in th
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.