iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 12514-2:2000

(Main)

Installations for oil supply systems for oil burners - Part 2: Safety requirements and tests - Parts, valves, pipes, filters, oil de-aerators, meters

Installations for oil supply systems for oil burners - Part 2: Safety requirements and tests - Parts, valves, pipes, filters, oil de-aerators, meters

This standard applies to valves, pipes, filters and meters of oil supply installations for automatic supply of one or more oil burners or oil consuming units with fuel oil from one or more central storage tanks under static or dynamic pressure. This standard covers all the above mentioned components between the connection to one or more tanks and the connection to oil burners or oil consuming units, including the direct series-connected shut-off devices.

Ölversorgungsanlagen für Ölbrenner - Teil 2: Sicherheitstechnische Anforderungen und Prüfungen - Bauelemente, Armaturen, Leitungen, Filter, Heizölentlüfter, Zähler

Diese Norm gilt für Ölförderaggregate, Ölversorgungsbehälter und zugehörige Regel- und Sicherheitseinrichtungen von Ölversorgungsanlagen zur selbstättigen Versorgung eines oder mehrerer Ölbrenner bzw. Ölverbrauchsstellen mit leichtem Heizöl (einer maximalen Viskosität von 10 mm2/s bei 20°C) aus einem oder mehreren zentralen Öllagerbehältern under statischem oder dynamischem Druck. Sie gilt für alle oben genannten Bauelemente vom Anschluß an den bzw. die Lagerbehälter bis zum Anschluß an den Ölbrenner bzw. Ölverbrauchsstellen einschließlich der unmittelbar vorgeschalteten Absperreinrichtungen.

Installations des systèmes d'alimentation de fioul pour les brûleurs de fioul domestique - Partie 2: Prescriptions de sécurité et essais - Composants, vannes, conduites, filtres, dégazeurs de fioul domestique, compteurs

Cette Norme Européenne s'applique aux vannes, conduites, filtres et compteurs dans les systèmes d'alimentation automatique de fioul domestique pour un ou plusieurs brûleurs ou unités de consommation de fioul domestique; les brûleurs sont alimentés à partir d'un ou plusieurs réservoirs centraux de fioul domestique, sous pression dynamique ou statique. Cette norme concerne tous les composants mentionnés ci-dessus et situés entre les connexions du ou des réservoirs de stockage et le brûleur de fioul domestique ou l'unité de consommation de fioul domestique, incluant les différents systèmes de sécurité qui déclenchent l'installation.

Napeljave za dovod olja oljnim gorilnikom - 2. del: Varnostne zahteve in preskušanje - Sestavni deli, armature, cevovodi, filtri, oljni odzračevalniki, števci

General Information

Status
Withdrawn
Publication Date
21-Mar-2000
Withdrawal Date
18-Aug-2020
ICS
27.060.10 - Liquid and solid fuel burners
Technical Committee
CEN/TC 47 - Atomizing oil burners and their components - Function - Safety - Testing
Drafting Committee
CEN/TC 47/WG 4 - Oil supply systems
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
19-Aug-2020
Ref Project
SIST EN 12514-2:2003 - Installations for oil supply systems for oil burners - Part 2: Safety requirements and tests - Parts, valves, pipes, filters, oil de-aerators, meters

Relations

Replaced By
EN 12514:2020 - Components for supply systems for consuming units with liquid fuels
Effective Date
26-Aug-2020
Revised
prEN 12514-4 - Parts for supply systems for consuming units with liquid fuels - Part 4: Safety requirements and tests - Pipings and parts within pipelines
Effective Date
19-Jan-2023
Revised
prEN 12514-3 - Parts for supply systems for consuming units with liquid fuels - Part 3: Safety requirements and tests - Valves and meters
Effective Date
19-Jan-2023
Revised
prEN 12514-1 - Parts for supply systems for consuming units with liquid fuels - Part 1: Safety requirements and tests - Terminology, general requirements
Effective Date
18-Jan-2023
Revised
prEN 12514-2 rev - Parts for supply systems for demand appliance with liquid fuels — Part 2: Safety requirements and tests — Feed pumps, control and safety devices, operating vessels
Effective Date
18-Jan-2023

Buy Standard

EN 12514-2:2003EN 12514-2:2003
PreviousNext
Standard
EN 12514-2:2003
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Ölversorgungsanlagen für Ölbrenner - Teil 2: Sicherheitstechnische Anforderungen und Prüfungen - Bauelemente, Armaturen, Leitungen, Filter, Heizölentlüfter, ZählerInstallations des systemes d'alimentation de fioul pour les bruleurs de fioul domestique - Partie 2: Prescriptions de sécurité et essais - Composants, vannes, conduites, filtres, dégazeurs de fioul domestique, compteursInstallations for oil supply systems for oil burners - Part 2: Safety requirements and tests - Parts, valves
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
prEN 267 rev(Main)
Forced draught burners for liquid fuels
oSIST prEN 267:2012

This European Standard specifies the terminology, the general requirements for the construction and operation of forced draught oil burners and also the provision of control and safety devices, and the test procedure for these burners.
This European Standard applies to forced draught oil burners supplied with:
―   fuel based on first raffinates and their mixtures with biogenous liquid fuels having a viscosity at the burner inlet of 1,6 mm2/s (cSt) up to 6 mm2/s (cSt) at 20 °C; and
―   higher boiling petroleum based first raffinates (viscosity greater than 6 mm2/s), that require preheating for proper atomization.
This European Standard is applicable to:
―   single burners fitted to a single combustion chamber;
―   single burners fitted to an appliance with additional requirements;
NOTE   When additional requirements apply which are not identified or specified in this standard, the specification of the required safety measures and/or protective devices and compliance with them is outside the scope of this standard.
―   single-fuel and dual-fuel burners when operating on oil only;
―   the oil function of dual-fuel burners designed to operate simultaneously on gaseous and liquid fuels.
This European Standard deals with all significant machine hazards, hazardous situations and events relevant to burners, when they are used as intended and under conditions of misuse which are reasonably foreseeable, see Annex J.
This European Standard also deals with the additional requirements for the burners in the scope with pressurized parts and/or firing pressurized bodies, see Annex K.
This European Standard specifies the requirements to ensure the safety during commissioning, start-up, operation, shut-down and maintenance.
This European Standard deals also with forced draught burners intended to be used with biogenous liquid fuels, mixtures.
This European Standard deals also with burners equipped to increase the total appliance efficiency; see Annex M.

  • Draft
    113 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 12514-4(Main)
Parts for supply systems for consuming units with liquid fuels - Part 4: Safety requirements and tests - Pipings and parts within pipelines
oSIST prEN 12514-4:2009

This European Standard applies to the following parts of supply systems for the automatic liquid fuel supply of consuming units from one or more tanks:
a)   pipes;
b)   fasteners;
c)   pipeline connections;
d)   parts within pipes;
Combinations of single parts are acceptable.

  • Draft
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 12514-2 rev(Main)
Parts for supply systems for demand appliance with liquid fuels — Part 2: Safety requirements and tests — Feed pumps, control and safety devices, operating vessels
oSIST prEN 12514-2:2009

This European Standard applies to the following parts of supply systems for the automatic supply of liquid fuel to one or more consuming units from one or more tanks:
a)   feed pumps;
b)   control and safety devices;
c)   service tanks;
d)   service vessels.
The combination of single parts is acceptable.

  • Draft
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 12514-3(Main)
Parts for supply systems for consuming units with liquid fuels - Part 3: Safety requirements and tests - Valves and meters
oSIST prEN 12514-3:2009

This European Standard applies to the following parts of supply systems for the automatic liquid fuel supply of consuming units from one or more tanks:
a)   isolating valve;
b)   quick-acting valve;
c)   switch-over valve;
d)   forced switch-over valve;
e)   check valve;
f)   pressure compensating device;
g)   discharge valve;
h)   pressure reducer;
i)   filter;
j)   meter;
k)   de-aerator;
l)   anti-siphon safety device;
m)   pressure retaining device;
n)   isolation device;
o)   pressure gauge;
p)   vapour/air separator;
q)   pressure control path;
r)   combined part
s)   other part.

  • Draft
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 12514-1(Main)
Parts for supply systems for consuming units with liquid fuels - Part 1: Safety requirements and tests - Terminology, general requirements
oSIST prEN 12514-1:2009

This European Standard applies to all parts of supply systems for the automatic supply of liquid fuel to one or more consuming units from one or more tanks. It applies to all parts from the tank connection(s) to the connection to the burner or the consuming units, respectively, including the direct series-connected shut-off devices.

  • Draft
    90 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 267:2009/FprA1(Amendment)
Automatic forced draught burners for liquid fuels
SIST EN 267:2010/kFprA1:2011

This European Standard specifies the terminology, the general requirements for the construction and operation of automatic forced draught oil burners and also the provision of control and safety devices, and the test procedure for these burners.
This European Standard applies to automatic forced draught oil burners supplied with:
-   a fuel having a viscosity at the burner inlet of 1,6 mm²/s (cSt) up to 6 mm²/s (cSt) at 20 °C; and
-   higher boiling petroleum based first raffinates (viscosity greater than 6 mm2/s), that require preheating for proper atomisation.
This European Standard is applicable to:
-   single burners fitted to a single combustion chamber;
-   single burners fitted to an appliance with additional requirements, then the relevant standard of this appliance shall be taken into account;
-   single-fuel and dual-fuel burners when operating on oil only;
-   the oil function of dual-fuel burners designed to operate simultaneously on gaseous and liquid fuels, in which case the requirements of EN 676 will also apply in respect of the gaseous fuel function.
This European Standard deals with all significant machine hazards, hazardous situations and events relevant to burners, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, see Annex J.
It deals with the additional requirements for the burners in the scope with pressurised parts and/or firing pressurised bodies, see Annex K.
This European Standard specifies the requirements to be met by the manufacturer to ensure the safety during commissioning, start-up, operation, shut-down and maintenance.
This European Standard does not deal with hazards due to specific applications.
This European Standard deals also with forced draught burners intended to be used with biogenous fuels, mixtures.
This European Standard deals also with burners equipped to increase the total appliance efficiency; see Annex L.

  • Draft
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6806:2024(Main)
Rubber hoses and hose assemblies for use in oil burners - Specification (ISO 6806:2024)
SIST EN ISO 6806:2024

This document specifies the minimum requirements for rubber hoses and hose assemblies for use in oil burners.
The following two types of hose assembly are specified:
—     Type 1: Hose assemblies for flux and reflux, but not for insertion between the oil burner pump and the atomizing connection; maximum working pressure 1,0 MPa (10 bar); maximum oil temperature 100 °C;
—     Type 2: Hose assemblies for insertion between the oil burner pump and the atomizing connection; maximum working pressure 4,0 MPa (40 bar); maximum oil temperature 100 °C.
The hose assemblies specified in this document are not intended to be used, without special assessment, for purposes other than oil burner installations.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 23553-1:2022(Main)
Safety and control devices for oil burners and oil-burning appliances - Particular requirements - Part 1: Automatic and semi-automatic valves (ISO 23553-1:2022)
SIST EN ISO 23553-1:2022

This document specifies safety, constructional and performance requirements and testing of automatic and semi-automatic valves for oil.
It applies to automatic and semi-automatic valves which are:
—    normally closed;
—    used in combustion plants to interrupt the oil flow with or without delay on closing;
—    for use with oil types (e.g. middle distillate fuel oil, crude oil, heavy fuel oil or kerosene) without gasoline;
NOTE 1    For other oil types (e.g. oil emulsions), additional test methods can be agreed between the manufacturer and the test authority.
NOTE 2    Oil types from petroleum refining processes are classified ISO-F-D in ISO 8216-99 and form part of a device having other function(s), such as oil pumps. In this case, the test methods apply to those parts or components of the device forming the automatic and semi-automatic valves, i.e. those parts which are necessary for the closing function.
—    for use on burners or in appliances using oil;
—    directly or indirectly operated, electrically or by mechanical or hydraulic means;
—    fitted with or without closed-position indicator switches.
This document covers type testing only.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12514:2020/AC:2021(Corrigendum)
Components for supply systems for consuming units with liquid fuels
SIST EN 12514:2020/AC:2021

2021-01-15 - JE- TC - Corrects the wording related to Formula (6) in 5.5.1.2.1.4, 5.5.1.2.2.3, 5.5.1.3.3, 5.5.1.4.3, 5.12.2.1.3, 5.12.2.2.3 and 5.19.20.4.3 + Consolidated text not in XML, as mother standard EN 12514:2020 was not prepared in XML

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12514:2020(Main)
Components for supply systems for consuming units with liquid fuels
SIST EN 12514:2020

This European Standard specifies the safety and performance requirements and tests methods for the components for supply systems. Their intended use is the supply with liquid fuel for one or more consuming units from one or more tanks.
This European Standard applies to pressurised, negative pressurised, unpressurised, underground, above ground, inside and/or outside systems to supply liquid fuels.
The components for supply systems covered by this standard are piping kits/systems and their components.
Not covered by this standard are items belonging to the consuming unit (e. g.: heating/cooling appliances in buildings) and items used for the mounting and support of components.
Not covered by this standard are items with the intended use of gas for building heating/cooling systems and any items of heating networks.
Not covered are items used for drainage (including highways) and disposal of other liquids and gaseous waste, supply of gases, pressure and vacuum systems, communications, sanitary and cleaning fixtures and storage fixtures.

  • Standard
    220 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    220 pages
    English language
    sale 10% off
    e-Library read for
    1 day