27.060.10 - Liquid and solid fuel burners

This European Standard specifies the safety and performance requirements and tests methods for the components for supply systems. Their intended use is the supply with liquid fuel for one or more consuming units from one or more tanks.
This European Standard applies to pressurised, negative pressurised, unpressurised, underground, above ground, inside and/or outside systems to supply liquid fuels.
The components for supply systems covered by this standard are piping kits/systems and their co...view more

This European Standard specifies the terminology, the general requirements for the construction and operation of forced draught oil burners and also the provision of control and safety devices, and the test procedure for these burners.
This European Standard applies to forced draught oil burners supplied with:
― fuel based on first raffinates and their mixtures with biogenous liquid fuels having a viscosity at the burner inlet of 1,6 mm2/s (cSt) up to 6 mm2/s (cSt) at 20 °C; and
― higher boiling...view more

This European Standard specifies the terminology, the general requirements for the construction and operation of forced draught oil burners and also the provision of control and safety devices, and the test procedure for these burners.
This European Standard applies to forced draught oil burners supplied with:
-   fuel based on first raffinates and their mixtures with biogenous liquid fuels having a viscosity at the burner inlet of 1,6 mm2/s (cSt) up to 6 mm2/s (cSt) at 20 °C, and
-   higher boil...view more

The test code applies to the determination of the perfomances of  heating boilers combi boilers and water heaters fired by liquid fuels. The requirements are laid down in EN 303-1 and EN 303-2.
This code includesthe requirements and recommendations for carrying out and evaluating the procedure for testing boilers and also the details of the technical conditions under which the tests shall be carried out.

This standard is applicable to heating boilers in accordance with EN 303-1 up to a nominal heat output of 1 000 kW and EN 303-4 up to a nominal heat output of 70 kW with atomizing oil burners  in accordance with EN 267 which are designed for operating with liquid fuels.
This European Standard applies to low temperature boilers in accordance with EN 303 1/A1 and specifies the heating related requirements necessary for liquid fuels for low temperature boilers and the required additional duration t...view more

This document specifies the minimum requirements for rubber hoses and hose assemblies for use in oil
burners.
The following two types of hose assembly are specified.
— Type 1: Hose assemblies for flux and reflux, but not for insertion between the oil burner pump
and the atomizing connection; maximum working pressure 1,0 MPa (10 bar); maximum oil
temperature 100 °C.
— Type 2: Hose assemblies for insertion between the oil burner pump and the atomizing connection;
maximum working pressure 4,...view more

ISO 6806:2017 specifies the minimum requirements for rubber hoses and hose assemblies for use in oil burners.
The following two types of hose assembly are specified.
- Type 1: Hose assemblies for flux and reflux, but not for insertion between the oil burner pump and the atomizing connection; maximum working pressure 1,0 MPa (10 bar); maximum oil temperature 100 °C.
- Type 2: Hose assemblies for insertion between the oil burner pump and the atomizing connection; maximum working pressure 4,0 MP...view more

ISO 6806:2017 specifies the minimum requirements for rubber hoses and hose assemblies for use in oil burners. The following two types of hose assembly are specified. - Type 1: Hose assemblies for flux and reflux, but not for insertion between the oil burner pump and the atomizing connection; maximum working pressure 1,0 MPa (10 bar); maximum oil temperature 100 °C. - Type 2: Hose assemblies for insertion between the oil burner pump and the atomizing connection; maximum working pressure 4,0 MPa (...view more

EN ISO 23553-1 specifies safety, constructional and performance requirements and testing of automatic and semi-automatic valves for oil. It applies to automatic and semi-automatic valves which are: - normally closed; - used in combustion plants to interrupt the oil flow with or without delay on closing; - for use with oil types (e.g. middle distillate fuel oil, crude oil, heavy fuel oil or kerosene) without gasoline.

ISO 23553-1:2014 specifies safety, constructional and performance requirements and testing of automatic and semi-automatic valves for oil.
It applies to automatic and semi-automatic valves which are:
-normally closed;
-used in combustion plants to interrupt the oil flow with or without delay on closing;
-for use with oil types (e.g. middle distillate fuel oil, crude oil, heavy fuel oil or kerosene) without gasoline;
-for use on burners or in appliances using oil;
-directly or indirectly op...view more

ISO 23553-1:2014 specifies safety, constructional and performance requirements and testing of automatic and semi-automatic valves for oil. It applies to automatic and semi-automatic valves which are: -normally closed; -used in combustion plants to interrupt the oil flow with or without delay on closing; -for use with oil types (e.g. middle distillate fuel oil, crude oil, heavy fuel oil or kerosene) without gasoline; -for use on burners or in appliances using oil; -directly or indirectly operated...view more

This European Standard specifies the safety, construction and performance requirements for automatic burner control systems, programming units and flame detector devices, intended for use with gas and oil burners and gas and oil burning appliances, with or without fans and similar use. This European Standard is applicable to automatic burner control systems that include additional functions. This European Standard does not cover automatic burner control systems utilizing thermo-electric flame su...view more

ISO 22968:2010 specifies the terminology, test procedures and general requirements for the construction and operation of automatic forced draught oil burners supplied with a fuel having a viscosity at the burner inlet of 1,6 mm2/s (cSt) to 6 mm2/s (cSt) at 20 °C or higher, boiling petroleum in accordance with ISO 8217-based first raffinates, and the provision of related control and safety devices. It is applicable to automatic oil burners fitted with a combustion air fan, equipped as described t...view more

This European Standard specifies a method for the determination of the spray characteristic and the index angle of oil pressure atomizing nozzles.

This European Standard specifies a method for the determination of the spray characteristic and the index angle of oil pressure atomizing nozzles.

This European Standard specifies the dimensions of motors for atomizing oil burners.

This European Standard specifies the dimensions for connectors and certain dimensional characteristics of pumps for atomizing oil burners.

This European Standard specifies the dimensions of motors for atomizing oil burners.

This European Standard specifies the dimensions for connectors and certain dimensional characteristics of pumps for atomizing oil burners.