EN ISO 5436-2:2012

Geometrical product specifications (GPS) - Surface texture: Profile method; Measurement standards - Part 2: Software measurement standards (ISO 5436-2:2012)

This part of ISO 5436 defines Type F1 and Type F2 software measurement standards (etalons) for verifying the software of measuring instruments. It also defines the file format of Type F1 software measurement standards for the calibration of instruments used for measuring the surface texture by the profile method defined in ISO 3274.
NOTE 1 Throughout this part of ISO 5436, the term "softgauge" is used as a substitute for "software measurement standard Type F1".
NOTE 2 Formerly, "measurement standards" were referred to as "calibration specimens".
NOTE 3 ISO 3274 only refers to instruments with independent reference datums.

Geometrische Produktspezifikation (GPS) - Oberflächenbeschaffenheit: Tastschnittverfahren; Normale - Teil 2: Software-Normale (ISO 5436-2:2012)

Dieser Teil von ISO 5436 legt die Software-Normale (Etalons) vom Typ F1 und F2 für die Prüfung der Software von Messgeräten fest. Außerdem legt er das Datenformat der Typ-F1-Software-Normale zur Kalibrierung von Messgeräten zur Messung der Oberflächenbeschaffenheit mit dem Profilverfahren nach ISO 3274 fest.
ANMERKUNG 1   In diesem Teil von ISO 5436 wird der Begriff „Software-Normale vom Typ F1“ durch „Software-Lehre“ ersetzt.
ANMERKUNG 2   Früher wurden „Normale“ als „Einstellnormale“ bezeichnet.
ANMERKUNG 3   ISO 3274 bezieht sich nur auf Messgeräte mit unabhängigen Bezügen.

Spécification géométrique des produits (GPS) - État de surface: Méthode du profil; Étalons - Partie 2: Étalons logiciels (ISO 5436-2:2012)

La présente partie de l'ISO 5436 définit les étalons logiciels de Type F1 et de Type F2, pour vérifier les logiciels des instruments de mesure. Elle définit également le format de fichier des étalons logiciels de Type F1 pour l'étalonnage d'instruments de mesure de l'état de surface par la méthode du profil telle que définie dans l'ISO 3274.
NOTE 1 Tout au long de la présente partie de l'ISO 5436, «calibre virtuel» est utilisé en remplacement d'«étalon logiciel de Type F1».
NOTE 2 Précédemment, les «étalons» étaient appelés «échantillons d'étalonnage».
NOTE 3 L'ISO 3274 se réfère uniquement à des instruments intégrant leur référence de guidage.

Specifikacija geometrijskih veličin izdelka - Tekstura površine: profilna metoda - Standardi za merjenje - 2. del: Standardi za merilno programsko opremo (ISO 5436-2:2012)

Ta del standarda ISO 5436 določa standarde za merilno programsko opremo tipov F1 in F2 (etalon) za preverjanje programske opreme merilnih instrumentov. Določa tudi obliko zapisa datoteke standardov za merilno programsko opremo tipa F1 za kalibracijo instrumentov, ki se uporabljajo za merjenje teksture površine s profilno metodo, ki jo določa standard ISO 3274.

General Information

• Status: Published
• Publication Date: 30-Sep-2012
• Withdrawal Date: 29-Apr-2013
• ICS: 17.040.30 - Measuring instruments
• Technical Committee: CEN/TC 290 - Dimensional and geometrical product specification and verification
• Drafting Committee: CEN/TC 290 - Dimensional and geometrical product specification and verification
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 01-Oct-2012
• Completion Date: 01-Oct-2012
• Ref Project: SIST EN ISO 5436-2:2013 - Geometrical product specifications (GPS) - Surface texture: Profile method; Measurement standards - Part 2: Software measurement standards (ISO 5436-2:2012)

Relations

• Replaces: EN ISO 5436-2:2001/prA1 - Geometrical Product Specifications (GPS) - Surface texture: Profile method; Measurement standards - Part 2: Software measurement standards - Amendment 1 (ISO 5436-2:2001/DAM 1:2010)
• Effective Date: 08-Oct-2012
• Replaces: EN ISO 5436-2:2001/AC:2008 - Geometrical Product Specifications (GPS) - Surface texture: Profile method; Measurement standards - Part 2: Software measurement standards (ISO 5436-2:2001/Cor 1:2006/Cor 2:2008)
• Effective Date: 08-Oct-2012
• Replaces: EN ISO 5436-2:2001 - Geometrical Product Specifications (GPS) - Surface texture: Profile method; Measurement standards - Part 2: Software measurement standards (ISO 5436-2:2001)
• Effective Date: 08-Oct-2012

Standards Content (Sample)

SLOVENSKI STANDARD
01-oktober-2013
1DGRPHãþD
SIST EN ISO 5436-2:2004
SIST EN ISO 5436-2:2004/AC:2008
SIST EN ISO 5436-2:2004/oprA1:2010
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND7HNVWXUDSRYUãLQHSURILOQDPHWRGD
6WDQGDUGL]DPHUMHQMHGHO6WDQGDUGL]DPHULOQRSURJUDPVNRRSUHPR,62

Geometrical product specifications (GPS) - Surface texture: Profile method;
Measurement standards - Part 2: Software measurement standards (ISO 5436-2:2012)
Geometrische Produktspezifikation (GPS) - Oberflächenbeschaffenheit:
Tastschnittverfahren; Normale - Teil 2: Software-Normale (ISO 5436-2:2012)
Spécification géométrique des produits (GPS) - État de surface: Méthode du profil;
Étalons - Partie 2: Étalons logiciels (ISO 5436-2:2012)
Ta slovenski standard je istoveten z: EN ISO 5436-2:2012
ICS:
17.040.30 Merila Measuring instruments
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 5436-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2012
ICS 17.040.30 Supersedes EN ISO 5436-2:2001
English Version
Geometrical product specifications (GPS) - Surface texture:
Profile method; Measurement standards - Part 2: Software
measurement standards (ISO 5436-2:2012)
Spécification géométrique des produits (GPS) - État de Geometrische Produktspezifikation (GPS) -
surface: Méthode du profil; Étalons - Partie 2: Étalons Oberflächenbeschaffenheit: Tastschnittverfahren; Normale
logiciels (ISO 5436-2:2012) - Teil 2: Software-Normale (ISO 5436-2:2012)
This European Standard was approved by CEN on 25 September 2012.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5436-2:2012: E
worldwide for CEN national Members.

Contents Page
Foreword .3

Foreword
This document (EN ISO 5436-2:2012) has been prepared by Technical Committee ISO/TC 213 "Dimensional
and geometrical product specifications and verification" in collaboration with Technical Committee
CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is
held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2013, and conflicting national standards shall be withdrawn at the
latest by April 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 5436-2:2001.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 5436-2:2012 has been approved by CEN as a EN ISO 5436-2:2012 without any modification.

INTERNATIONAL ISO
STANDARD 5436-2
Second edition
2012-10-01
Geometrical product specifications
(GPS) — Surface texture: Profile method;
Measurement standards —
Part 2:
Software measurement standards
Spécification géométrique des produits (GPS) — État de surface:
Méthode du profil; Étalons —
Partie 2: Étalons logiciels
Reference number
ISO 5436-2:2012(E)
©
ISO 2012
ISO 5436-2:2012(E)
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

ISO 5436-2:2012(E)
Contents Page
Foreword .iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Type F software measurement standards . 2
4.1 General . 2
4.2 Type F1 — Reference data . 3
4.3 Type F2 — Reference software . 3
5 File format for Type F1 reference data . 3
5.1 General . 3
5.2 Record 1 — Header . 4
5.3 Record 2 — Other information (optional and non-mandatory) . 6
5.4 Record 3 data . 8
5.5 Record 4 checksum . 9
6 Software measurement standard certificate . 9
Annex A (informative) Example of file format . 11
Annex B (informative) Relation to the GPS matrix model .15
Bibliography .17
ISO 5436-2:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 5436-2 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product
specifications and verification.
This second edition cancels and replaces the first edition (ISO 5436-2:2001), which has been technically revised.
It also incorporates the Technical Corrigenda ISO 5436-2:2001/Cor.1:2006 and ISO 5436-2:2001/Cor.2:2008.
ISO 5436 consists of the following parts, under the general title Geometrical product specifications (GPS) —
Surface texture: Profile method; Measurement standards:
— Part 1: Material measures
— Part 2: Software measurement standards
iv © ISO 2012 – All rights reserved

ISO 5436-2:2012(E)
Introduction
This part of ISO 5436 is a geometrical product specification (GPS) standard and is to be regarded as a general
GPS standard (see ISO/TR 14638). It influences chain link 6 of the chain of standards on roughness, waviness
and primary profiles.
The ISO/GPS Masterplan given in ISO/TR 14638 gives an overview of the ISO/GPS system of which this
document is a part. The fundamental rules of ISO/GPS given in ISO 8015 apply to this document and the
default decision rules given in ISO 14253-1 apply to specifications made in accordance with this document,
unless otherwise indicated.
For more detailed information on the relationship of this part of ISO 5436 to other standards and the GPS
matrix model, see Annex B.
This part of ISO 5436, together with ISO 5436-1, introduces two new measurement standards:
— Type E, for calibrating the profile co-ordinate system;
— Type F, for calibrating software.
This part of ISO 5436 is concerned with software measurement standards.
INTERNATIONAL STANDARD ISO 5436-2:2012(E)
Geometrical product specifications (GPS) — Surface texture:
Profile method; Measurement standards —
Part 2:
Software measurement standards
1 Scope
This part of ISO 5436 defines Type F1 and Type F2 software measurement standards (etalons) for verifying the
software of measuring instruments. It also defines the file format of Type F1 software measurement standards for
the calibration of instruments used for measuring the surface texture by the profile method defined in ISO 3274.
NOTE 1 Throughout this part of ISO 5436, the term “softgauge” is used as a substitute for “software measurement
standard Type F1”.
NOTE 2 Formerly, “measurement standards” were referred to as “calibration specimens”.
NOTE 3 ISO 3274 only refers to instruments with independent reference datums.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced document
(including any amendments) applies.
ISO 3274:1996, Geometrical Product Specifications (GPS) — Surface texture: Profile method — Nominal
characteristics of contact (stylus) instruments
ISO 5436-1:2000, Geometrical Product Specifications (GPS) — Surface texture: Profile method; Measurement
standards — Part 1: Material measures
ISO 12085:1996, Geometrical Product Specifications (GPS) — Surface texture: Profile method — Motif parameters
ISO 16610-21:2011, Geometrical product specifications (GPS) — Filtration — Part 21: Linear profile filters:
Gaussian filters
ISO 17450-2:2012, Geometrical product specifications (GPS) — General concepts — Part 2: Basic tenets,
specifications, operators, uncertainties and ambiguities
ISO/IEC Guide 98-3:2008, Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in
Measurement (GUM:1995)
ISO/IEC Guide 99:2007, International vocabulary of metrology — Basic and general concepts and
associated terms (VIM)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 3274, ISO 5436-1, ISO 12085,
ISO 16610-21:2011, ISO/
...