EN 14197-2:2003

Cryogenic vessels - Static non-vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing

This European Standard specifies requirements for the design, fabrication, inspection and testing of static non-vacuum insulated cryogenic vessels designed for a maximum allowable pressure of more than 0,5 bar.
This European standard applies to static non-vacuum insulated cryogenic vessels for fluids as specified in prEN 14197-1 and does not apply to vessels designed for toxic fluids.
For static non-vacuum insulated cryogenic vessels designed for a maximum allowable pressure of not more than 0,5 bar this European Standard may be used as a guide

Kryo-Behälter - Ortsfeste, nicht vakuum-isolierte Behälter - Teil 2: Bemessung, Herstellung und Prüfung

Diese Europäische Norm gilt  für die Bemessung, Herstellung und Prüfung von ortsfesten, nicht vakuum-isolierten Kryo-Behältern, die für einen höchstzulässigen Betriebsdruck von über 0,5 bar bemessen sind.
Diese Norm gilt für ortsfeste, nicht vakuum-isolierte Kryo-Behälter für Fluide, die in EN 14197-1 festgelegt sind, und sie gilt nicht für giftige Fluide.
Für ortsfeste, nicht vakuum-isolierte Kryo-Behälter mit einem höchstzulässigen Betriebsdruck von weniger als 0,5 bar kann diese Norm als eine Richtlinie angewendet werden.

Récipients cryogéniques - Récipients statiques, non isolés sous vide - Partie 2: Conception, fabrication, inspection et essais

La présente Norme européenne spécifie les exigences relatives à la conception, à la fabrication, à l'inspection et aux essais de récipients cryogéniques statiques non isolés sous vide conçus pour une pression maximale admissible supérieure à 0,5 bar.
La présente Norme européenne s'applique aux récipients cryogéniques statiques non isolés sous vide destinés à contenir les fluides tels que spécifiés dans l'EN 14197-1 et ne s'applique pas aux récipients conçus pour des fluides toxiques.
La présente Norme européenne peut servir de guide pour les récipients cryogéniques statiques non isolés sous vide prévus pour une pression maximale admissible inférieure ou égale à 0,5 bar.

Kriogene posode – Stabilne, vakuumsko neizolirane posode - 2. del: Konstruiranje, izdelava, kontrola in preskus

General Information

• Status: Published
• Publication Date: 25-Nov-2003
• Withdrawal Date: 30-May-2004
• ICS: 23.020.40 - Cryogenic vessels
• Technical Committee: CEN/TC 268 - Cryogenic vessels
• Drafting Committee: CEN/TC 268/WG 2 - Compatibility, insulation, accessories
• Current Stage: 9060 - Closure of 2 Year Review Enquiry - Review Enquiry
• Start Date: 03-Mar-2024
• Completion Date: 03-Mar-2024
• Directive: 2014/68/EU - Directive 2014/68/EU of the European Parliament and of the Council of 15 May 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of pressure equipment
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: SIST EN 14197-2:2004 - Cryogenic vessels - Static non-vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing

Relations

• Amended By: EN 14197-2:2003/A1:2006 - Cryogenic vessels - Static non-vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing
• Effective Date: 22-Dec-2008
• Corrected By: EN 14197-2:2003/AC:2006 - Cryogenic vessels - Static non-vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing
• Effective Date: 22-Dec-2008
• Parent: EN 14197-1:2003 - Cryogenic vessels - Static non-vacuum insulated vessels - Part 1: Fundamental requirements
• Effective Date: 22-Dec-2008

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cryogenic vessels - Static non-vacuum insulated vessels - Part 2: Design, fabrication, inspection and testingKriogene posode – Stabilne, vakuumsko neizolirane posode - 2. del: Konstruiranje, izdelava, kontrola in preskusRécipients cryogéniques - Récipients statiques, non isolés sous vide - Partie 2: Conception, fabrication, inspection et essaisKryo-Behälter - Ortsfeste, nicht vakuum-isolierte Behälter - Teil 2: Bemessung, Herstellung und PrüfungTa slovenski standard je istoveten z:EN 14197-2:2003SIST EN 14197-2:2004en23.020.40ICS:SLOVENSKI
STANDARDSIST EN 14197-2:200401-junij-2004

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14197-2November 2003ICS 23.020.40English versionCryogenic vessels - Static non-vacuum insulated vessels - Part2: Design, fabrication, inspection and testingRécipients cryogéniques - Récipients fixes, non isolés sousvide - Partie 2: Conception, fabrication, inspection et essaisKryo-Behälter - Ortsfeste, nicht vakuum-isolierte Behälter -Teil 2: Bemessung, Herstellung und PrüfungThis European Standard was approved by CEN on 1 September 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14197-2:2003 E

(corner joint) with an opening angle jj = 10° to70°.36Figure 11 — Opening factor CA for flat ends and plates without additional marginal moment.37Figure 12 – Design factors for unstayed circular flat ends and plates.39Figure 13 — Design factor CE for rectangular or elliptical flat plates.40Figure 14 — Increased thickness of a cylindrical shell.41Figure 15 — Increased thickness of a conical shell.41Figure 16 — Set-on reinforcement ring.41Figure 17 — Set-in reinforcement ring.41Figure 18 — Pad reinforcement.42Figure 19 — Nozzle reinforcement.42Figure 20 — Necked out opening.42Figure 21 — Pad.43Figure 22 — Calculation scheme for cylindrical shells.43Figure 23 — Calculation scheme for spherical shells.44Figure 24 — Calculation scheme for adjacent nozzles or in a longitudinal direction of a cylinder.44Figure 25 — Openings between longitudinal and circumferential direction.45Figure 26 — Calculation scheme for adjacent nozzles in a sphere or in a circumferential directionof a cylinder.455Fabrication.465.1General.465.2Cutting.465.3Cold forming.465.4Hot forming.475.5Manufacturing tolerances.48Figure 27 a) — Seams which do not require a taper.49Figure 27 b) — Seams which do require a taper.49Figure 27 — Plate alignment.49Figure 28 — Gauge details.515.6Welding.515.7Non-welded permanent joints.526Inspection and testing.536.1Quality
plan.536.2Production control test plates.536.3Non-destructive testing.556.4Rectification.586.5Pressure testing.59Annex A (normative)
Elastic stress analysis.60A.1General.60A.2Terminology.60A.3Limit for longitudinal compressive general membrane stress.62

Additional Requirements for 9 % Ni steel.69B.1Introduction.69B.2Specific requirements.69Annex C (Informative) Pressure strengthening of vessels from austenitic stainless steels.71C.1Introduction.71C.2Field of application.71C.3Definitions and units of measurement.71C.4Materials.72C.5Design.73C.6Manufacturing and inspection.76C.7Comments.
...