EN ISO 19893:2018
(Main)Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of mounted assemblies to temperature cycling (ISO 19893:2011)
Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of mounted assemblies to temperature cycling (ISO 19893:2011)
ISO 19893:2011 specifies a method for testing the resistance to temperature cycling of joints for piping systems with rigid or flexible thermoplastics pipes.
It is applicable to thermoplastics piping systems intended to be used in hot and cold water pressure applications.
Kunststoff-Rohrleitungssysteme - Rohre und Formstücke aus Thermoplasten für Warm- und Kaltwasser - Prüfverfahren für die Widerstandsfähigkeit von montierten Baugruppen gegen Temperaturwechselbeanspruchung (ISO 19893:2011)
Systèmes de canalisations en plastique - Tubes thermoplastiques et raccords pour eau chaude et froide - Méthode d'essai de la résistance des assemblages à des cycles de température (ISO 19893:2011)
L'ISO 19893:2011 spécifie une méthode d'essai de la résistance à des cycles de températures des assemblages pour systèmes de canalisations comportant des tubes thermoplastiques rigides ou flexibles.
Elle est applicable aux systèmes de canalisations thermoplastiques destinés aux installations d'eau chaude et froide sous pression.
Cevni sistemi iz polimernih materialov - Plastomerne cevi in fitingi za hladno in toplo vodo - Preskusna metoda za ugotavljanje odpornosti sistema proti cikličnim temperaturnim spremembam (ISO 19893:2011)
Standard ISO 19893:2011 določa metodo za preskušanje odpornosti spojev za cevne sisteme s togimi ali fleksibilnimi termoplastičnimi cevmi proti cikličnim temperaturnim spremembam.
Uporablja se za sisteme s termoplastičnimi cevmi, namenjene za uporabo s tlačnimi sistemi za toplo in hladno vodo.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2018
1DGRPHãþD
SIST EN 12293:2000
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY3ODVWRPHUQHFHYLLQILWLQJL]DKODGQRLQ
WRSORYRGR3UHVNXVQDPHWRGD]DXJRWDYOMDQMHRGSRUQRVWLVLVWHPDSURWLFLNOLþQLP
WHPSHUDWXUQLPVSUHPHPEDP ,62
Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test
method for the resistance of mounted assemblies to temperature cycling (ISO
19893:2011)
Kunststoff-Rohrleitungssysteme - Rohre und Formstücke aus Thermoplasten für Warm-
und Kaltwasser - Prüfverfahren für die Widerstandsfähigkeit von montierten Baugruppen
gegen Temperaturwechselbeanspruchung (ISO 19893:2011)
Systèmes de canalisations en plastique - Tubes thermoplastiques et raccords pour eau
chaude et froide - Méthode d'essai de la résistance des assemblages à des cycles de
température (ISO 19893:2011)
Ta slovenski standard je istoveten z: EN ISO 19893:2018
ICS:
23.040.01 Deli cevovodov in cevovodi Pipeline components and
na splošno pipelines in general
91.140.60 Sistemi za oskrbo z vodo Water supply systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 19893
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2018
EUROPÄISCHE NORM
ICS 23.040.20; 23.040.45 Supersedes EN 12293:1999
English Version
Plastics piping systems - Thermoplastics pipes and fittings
for hot and cold water - Test method for the resistance of
mounted assemblies to temperature cycling (ISO
19893:2011)
Systèmes de canalisations en plastique - Tubes Kunststoff-Rohrleitungssysteme - Rohre und
thermoplastiques et raccords pour eau chaude et Formstücke aus Thermoplasten für Warm- und
froide - Méthode d'essai de la résistance des Kaltwasser - Prüfverfahren für die
assemblages à des cycles de température (ISO Widerstandsfähigkeit von montierten Baugruppen
19893:2011) gegen Temperaturwechselbeanspruchung (ISO
19893:2011)
This European Standard was approved by CEN on 1 September 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19893:2018 E
worldwide for CEN national Members.
EN 19893:2018 (E)
Contents Page
European foreword . 3
EN 19893:2018 (E)
European foreword
The text of ISO 19893:2011 has been prepared by Technical Committee ISO/TC 138 "Plastics pipes,
fittings and valves for the transport of fluids” of the International Organization for Standardization
(ISO) and has been taken over as EN 19893:2018 by Technical Committee CEN/TC 155 “Plastics piping
systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2019, and conflicting national standards shall
be withdrawn at the latest by September 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12293:1999.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 19893:2011 has been approved by CEN as EN 19893:2018 without any modification.
INTERNATIONAL ISO
STANDARD 19893
First edition
2011-12-15
Plastics piping systems —
Thermoplastics pipes and fittings for hot
and cold water — Test method for the
resistance of mounted assemblies to
temperature cycling
Systèmes de canalisations en plastique — Tubes thermoplastiques et
raccords pour eau chaude et froide — Méthode d'essai de la résistance
des assemblages à des cycles de température
Reference number
ISO 19893:2011(E)
©
ISO 2011
ISO 19893:2011(E)
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
ISO 19893:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 19893 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the
transport of fluids, Subcommittee SC 5, General properties of pipes, fittings and valves of plastic materials and
their accessories — Test methods and basic specifications.
INTERNATIONAL STANDARD ISO 19893:2011(E)
Plastics piping systems — Thermoplastics pipes and fittings for
hot and cold water — Test method for the resistance of
mounted assemblies to temperature cycling
1 Scope
This International Standard specifies a method for testing the resistance to temperature cycling of joints for
piping systems with rigid or flexible thermoplastics pipes.
It is applicable to thermoplastics piping systems intended to be used in hot and cold water pressure
applications.
2 Principle
A test assembly of pipes and fittings (see Figure 1) is subjected to temperature cycling by the passage of
water under pressure using hot and cold water alternately, for a specified number of cycles.
While being subjected to temperature cycling, parts of the assembly of pipes and fittings are maintained under
tensile stress and/or flexural strain using static clamps.
During and after the test, the assembly is monitored for signs of leakage.
NOTE It is assumed that the following test parameters are set by the reference product standard (i.e. the standard
making reference to this International Standard):
a) the test temperatures (see 3.1, 3.2 and 6.1);
b) the duration of a complete cycle and each part of the cycle (see 3.1, 3.2 and 6.1);
c) the test pressure (see 3.6 and 6.1);
d) the tensile stress (see 3.8 and 5.3);
e) the bending radius (see Clause 4 and Figures 1 and 2);
f) the total number of cycles, including the first five cycles (see 6.2 and 6.3).
ISO 19893:2011
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.