Copper and copper alloys - Plumbing fittings - Part 3: Compression fittings for use with plastics and multilayer pipes

This document specifies product characteristics, assessment methods, compliance criteria of test results and a designation system for fittings with compression ends for use with plastics and multilayer pipes which are defined in the applicable pipe standard. For the purposes of joining plastics pipes, the fitting ends have a nominal diameter from 6 mm to 160 mm. The fittings are designed for a service lifetime up to fifty years.
The compression fittings are used up to the operating temperatures and corresponding maximum operating pressures as indicated in Annex A.
This document applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.
Adaptor fittings for use with plastics and multilayer pipes may combine compression ends with fitting ends defined in the other parts of EN 1254.
Compression fittings for use with plastics and multilayer pipes may also have flanged end connections according to EN 1092-3.
Compression fittings for use with plastics and multilayer pipes may also have a plated or other decorative surface coating.
Fittings can be produced by machining, metal forming, casting, or fabrication.
Products covered by this document are intended to be used in:
a) liquid applications:
- hot, cold or combined hot and cold water, including systems according to EN 806;
- closed heating systems according to EN 12828;
- cooling systems;
- drainage systems;
- fire protection systems including sprinkler systems according to EN 12845.
b) gas applications (not valid for multilayer pipes):
- natural gas and liquefied petroleum gas systems with a maximum operating pressure less than or equal to 5 bar according to EN 1775;
- compressed air systems.

Kupfer und Kupferlegierungen - Fittings - Teil 3: Klemmverbinder für Kunststoffrohre und Mehrschichtverbundrohre

Dieses Dokument legt Produkteigenschaften, Bewertungsverfahren, Übereinstimmungskriterien der Prüf-ergebnisse und ein Bezeichnungssystem für Klemmverbindungen für Kunststoff- und Mehrschichtverbund-rohre, die in der geltenden Rohrnorm definiert sind, fest. Zum Verbinden von Kunststoffrohren haben die Fittingenden einen Nenndurchmesser von 6 mm bis 160 mm. Die Fittings sind für eine Lebensdauer von bis zu fünfzig Jahren ausgelegt.
Die Klemmverbindungen werden bis zu den in Anhang A angegebenen Betriebstemperaturen und entsprechenden maximalen Betriebsdrücken eingesetzt.
Dieses Dokument ist anzuwenden für Fittings aus Kupferlegierungen. Eine nicht erschöpfende Liste dieser Kupferlegierungen ist in CEN/TS 13388 enthalten.
Übergangsfittings für Kunststoff- und Mehrschichtverbundrohre dürfen Klemmverbindungen mit in den anderen Teilen der EN 1254 definierten Fittingenden kombinieren.
Klemmverbindungen für Kunststoff- und Mehrschichtverbundrohre dürfen auch Flanschendanschlüsse nach EN 1092-3 aufweisen.
Klemmverbindungen für Kunststoff- und Mehrschichtverbundrohre dürfen auch galvanische oder andere dekorative Oberflächenüberzüge aufweisen.
Fittings können durch Bearbeiten, Metallumformen, Gießen oder Fertigen hergestellt werden.
Die unter dieses Dokument fallenden Produkte sind für den Einsatz bestimmt in:
a) Flüssigkeitsanwendungen:
- warmes, kaltes oder kombiniertes Warm- und Kaltwasser, einschließlich Systeme nach EN 806;
- geschlossene Heizungsanlagen nach EN 12828;
- Kühlsysteme;
- Entwässerungssysteme;
- Brandbekämpfungsanlagen einschließlich Sprinkleranlagen nach EN 12845.
b) Gasanwendungen (gilt nicht für Mehrschichtverbundrohre):
- Erdgas- und Flüssiggasanlagen mit einem maximalen Betriebsdruck von weniger als oder gleich 5 bar nach EN 1775;
- Druckluftsysteme.

Cuivre et alliages de cuivre - Raccords - Partie 3 : Raccords à compression pour tubes en matières plastiques et multicouches

Le présent document spécifie les caractéristiques de produits, les méthodes d'évaluation, les critères de
conformité des résultats d'essais et un système de désignation pour les extrémités de raccords à
compression pour tubes en matières plastiques et multicouches qui sont définis dans la norme de
tuyauteries applicable. Pour l'assemblage de tubes en matières plastiques, les extrémités de raccords ont
un diamètre nominal compris entre 6 mm et 160 mm. Les raccords sont conçus pour une durée de vie en
service supérieure à 50 ans.
Les raccords à compression sont utilisés jusqu'aux températures de service et aux pressions maximales
de service correspondantes indiquées à l'Annexe A.
Le présent document s'applique aux raccords en alliage de cuivre. Une liste non exhaustive de ces alliages
de cuivre figure dans la CEN/TS 13388.
Les raccords adaptateurs utilisés avec des tubes en matières plastiques et multicouches peuvent
combiner des extrémités à compression avec des extrémités de raccord définies dans les autres parties
de l’EN 1254.
Les raccords à compression pour tubes en plastique et multicouches peuvent également comporter des
raccordements à brides conformément à l’EN 1092-3.
Les raccords à compression pour tubes en plastique et multicouches peuvent également avoir une surface
plaquée ou un autre revêtement de surface décoratif.
Les raccords peuvent être fabriqués par usinage, formage des métaux, moulage ou mécanosoudage.
Les produits couverts par le présent document sont destinés à être utilisés dans :
a) les applications liquides :
- les systèmes d'eau chaude, d'eau froide ou d'eau chaude et d'eau froide combinées, y compris les
systèmes conformes à l’EN 806 ;
- les systèmes de chauffage fermés conformes à l'EN 12828;
- les systèmes de refroidissement ;
- les systèmes de purge ;
- les systèmes de protection contre l'incendie, y compris les systèmes d'extinction de type
sprinkleur conformes à l’EN 12845.
b) les applications de gaz (ne s'applique pas aux tubes multicouches) :
- les systèmes fonctionnant au gaz naturel et des systèmes fonctionnant au gaz de pétrole liquéfiés
avec une pression maximale de service inférieure ou égale à 5 bar, conformément à l'EN 1775 ;
- les systèmes d’air comprimé.

Baker in bakrove zlitine - Fitingi - 3. del: Fitingi z nakrčenima priključkoma za spajanje s plastičnimi in večplastnimi cevmi

General Information

Status
Published
Publication Date
25-May-2021
Withdrawal Date
25-Nov-2021
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
26-May-2021
Due Date
26-Nov-2020
Completion Date
26-May-2021

Relations

Buy Standard

Standard
EN 1254-3:2021
English language
36 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-julij-2021
Nadomešča:
SIST EN 1254-3:2000
Baker in bakrove zlitine - Fitingi - 3. del: Fitingi z nakrčenima priključkoma za
spajanje s plastičnimi in večplastnimi cevmi
Copper and copper alloys - Plumbing fittings - Part 3: Compression fittings for use with
plastics and multilayer pipes
Kupfer und Kupferlegierungen - Fittings - Teil 3: Klemmverbindungen für Kunststoffrohre
und Mehrschichtverbundrohre
Cuivre et alliages de cuivre - Raccords - Partie 3 : Raccords à compression pour tubes
en matières plastiques et multicouches
Ta slovenski standard je istoveten z: EN 1254-3:2021
ICS:
23.040.40 Kovinski fitingi Metal fittings
77.150.30 Bakreni izdelki Copper products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 1254-3
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2021
EUROPÄISCHE NORM
ICS 23.040.40 Supersedes EN 1254-3:1998
English Version
Copper and copper alloys - Plumbing fittings - Part 3:
Compression fittings for use with plastics and multilayer
pipes
Cuivre et alliages de cuivre - Raccords - Partie 3 : Kupfer und Kupferlegierungen - Fittings - Teil 3:
Raccords à compression pour tubes en matières Klemmverbindungen für Kunststoffrohre und
plastiques et multicouches Mehrschichtverbundrohre
This European Standard was approved by CEN on 23 November 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1254-3:2021 E
worldwide for CEN national Members.

Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 7
3 Terms and definitions . 9
4 Product characteristics . 9
4.1 Internal pressure . 9
4.2 Tightness . 9
4.3 Resistance to high temperature for fittings with elastomeric seals (for heating
networks) . 10
4.4 Release of dangerous substances . 10
4.5 Durability . 11
4.6 Wall thickness at the threaded portions of fittings and/or compression nut . 11
4.7 Dimensions of tail pipe ends for swivel fittings . 11
4.8 Dimensions of gas union connectors . 12
4.9 Threaded end dimensions . 12
4.10 Other adapter ends (not defined in EN 1254-20:2021) . 12
4.11 Bore dimensions . 12
4.12 Identity of elastomeric sealing material for liquid applications . 12
4.13 Identity of elastomeric sealing material for gas applications . 12
4.14 Pipe abutment . 13
4.15 Alignment of the fitting ends . 13
4.16 Shapes for tightening systems . 13
4.17 Surface condition . 13
4.18 Plated or coated surfaces . 13
5 Testing, assessment and sampling methods . 13
5.1 General . 13
5.2 Internal pressure . 14
5.3 Tightness . 15
5.4 Durability . 19
5.5 Wall thickness at threaded portions of adaptor fittings . 19
5.6 Dimensions of tail pipe ends for swivel fittings . 20
5.7 Dimensions of gas union connectors . 20
5.8 Threaded end dimensions . 20
5.9 Bore dimensions . 20
5.10 Identity of elastomeric sealing material for liquid applications . 20
5.11 Identity of elastomeric sealing material for gas applications . 20
5.12 Alignment of the fitting ends . 20
6 Evaluation of conformity . 21
6.1 General . 21
6.2 Type testing . 21
6.3 Factory production control (FPC) . 27
7 Designation. 31
8 Marking, labelling and packaging . 31
8.1 General . 31
8.2 Additional marking . 31
8.3 Dezincification resistant copper zinc alloys . 32
Annex A (normative) Operating temperatures and design pressures . 33
Bibliography . 35

European foreword
This document (EN 1254-3:2021) has been prepared by Technical Committee CEN/TC 133 “Copper and
copper alloys”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2021, and conflicting national standards
shall be withdrawn at the latest by Novemeber 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1254-3:1998.
The main changes compared to EN 1254-3:1998 are:
— improved alignment with plastics and multilayer pipe standards for hot and cold water
applications;
— separation of test methods into part 20.
This part of the standard (EN 1254-3) should be read in conjunction with EN 1254-20:2021.
EN 1254 comprises the following parts under the general title “Copper and copper alloys — Plumbing
fittings”:
— Part 1: Capillary fittings for soldering or brazing to copper tubes
— Part 2: Compression fittings for use with copper tubes
— Part 3: Compression fittings for use with plastics and multilayer pipes
— Part 4: Threaded fittings
— Part 5: Capillary fittings with short ends for brazing to copper tubes
— Part 6: Push-fit fittings for use with metallic tubes, plastics and multilayer pipes
— Part 7: Press fittings for use with metallic tubes
— Part 8: Press fittings for use with plastics and multilayer pipes
— Part 20: Definitions, thread dimensions, test methods, reference data and supporting information
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Introduction
Products complying with this document may be used for several fluids including the transport of water
intended for human consumption if they comply with the relevant national, regional or local regulatory
provisions applicable in the place of use.
1 Scope
This document specifies product characteristics, assessment methods, compliance criteria of test results
and a designation system for fittings with compression ends for use with plastics and multilayer pipes
which are defined in the applicable pipe standard. For the purposes of joining plastics pipes, the fitting
ends have a nominal diameter from 6 mm to 160 mm. The fittings are designed for a service lifetime up
to fifty years.
The compression fittings are used up to the operating temperatures and corresponding maximum
operating pressures as indicated in Annex A.
This document applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in
CEN/TS 13388.
Adaptor fittings for use with plastics and multilayer pipes may combine compression ends with fitting
ends defined in the other parts of EN 1254.
Compression fittings for use with plastics and multilayer pipes may also have flanged end connections
according to EN 1092-3.
Compression fittings for use with plastics and multilayer pipes may also have a plated or other
decorative surface coating.
Fittings can be produced by machining, metal forming, casting, or fabrication.
Products covered by this document are intended to be used in:
a) liquid applications:
— hot, cold or combined hot and cold water, including systems according to EN 806;
— closed heating systems according to EN 12828;
— cooling systems;
— drainage systems;
— fire protection systems including sprinkler systems according to EN
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.