EN 14656:2006+A1:2010
(Main)Safety of machinery - Safety requirements for extrusion presses for steel and non-ferrous metals
Safety of machinery - Safety requirements for extrusion presses for steel and non-ferrous metals
This European Standard applies to:
- extrusion presses from the exit side of the heater through associated handling, cooling and quenching equipment including, e.g. the puller, the hot saw, the run-out table, the stretcher, the cold saw, cold saw table and/or coiler when incorporated into the equipment, to a point where the extruded product is passed to associated finishing equipment.
It specifies the health and safety requirements at all stages in the life of the equipment, its design, ordering, construction, use and disposal.
This European Standard specifies requirements to be met by the manufacturer to ensure the health and safety of persons during construction, transport, commissioning, operation, maintenance and de-commissioning, as well as in the event of foreseeable faults as malfunctions which may occur in the equipment.
This European Standard deals with all significant hazards, hazardous situations and events relevant to extrusion presses when they are used as intended and under conditions which are reasonably foreseeable by the manufacturer (see Clause 4).
This European Standard is not applicable to extrusion presses which are manufactured before the date of its publication as EN.
Sicherheit von Maschinen - Sicherheitsanforderungen an Strangpressen für Stahl und NE-Metalle
Diese Europäische Norm gilt für:
- Strangpressen, von der Ausgangsseite der Erwärmung über verbundene Handling-, Kühl- und Abschreckeinrichtungen, z. B. Abziehvorrichtung, Warmsäge, Auslauftisch, Strecker, Kaltsäge, Kaltsägetisch und/oder Haspel, sofern diese einen Bestandteil der betreffenden Maschine bilden, bis hin zum Übergabepunkt des jeweiligen Strangpressteils an die darauf folgende Adjustage.
Sie legt die Gesundheits- und Sicherheitsanforderungen über den gesamten Lebenszyklus der Ausrüstung, der Konstruktion, Bestellung, Montage, Betrieb und Entsorgung fest.
Diese Europäische Norm legt die Anforderungen fest, die der Hersteller einhalten muss, um Gesundheit und Sicherheit von Personen bei Montage, Transport, Inbetriebnahme, Betrieb, Wartung und Außerbetriebnahme zu gewährleisten, sowie die Anforderungen zum Ausschluss vorhersehbarer, maschinenseitig eventuell auftretender Fehlfunktionen.
Diese Europäische Norm behandelt alle signifikanten Gefährdungen, Gefährdungssituationen und -ereignisse, die für Strangpressen relevant sind, wenn diese bestimmungsgemäß und unter Bedingungen, die vernünf-tigerweise für den Hersteller vorhersehbar sind, verwendet werden (siehe Abschnitt 4).
Diese Europäische Norm ist nicht anwendbar für Strangpressen, die vor der Veröffentlichung dieser Norm als EN hergestellt wurden.
Sécurité des machines - Exigences de sécurité pour presses à filer l'acier et les métaux non ferreux
La présente norme s'applique :
— aux presses à filer, de la sortie du four de chauffage des billettes aux équipements de manutention, de refroidissement et de trempe associés, comprenant par exemple, l'extracteur (le puller), la scie à chaud, la table de sortie, le banc de traction, la scie à froid, la table de sciage à froid et/ou la bobineuse incorporés à l'équipement, jusqu'au point où le produit extrudé est transféré à l'équipement de finition associé.
Elle spécifie les exigences en matière de santé et de sécurité à tous les stades du cycle de vie de l'équipement, sa conception, sa commande, sa construction, son utilisation et sa mise au rebut.
La présente Norme européenne spécifie les exigences que le fabricant doit respecter afin d'assurer la santé et la sécurité des personnes lors des opérations de construction, transport, mise en service, fonctionnement, entretien et mise hors service, ainsi que dans l'éventualité de pannes prévisibles telles que des dysfonctionnements susceptibles de se produire.
La présente Norme européenne traite tous les phénomènes, situations et événements dangereux significatifs pertinents pour les presses à filer, lorsqu’elles sont utilisées comme prévu et dans des conditions raisonnablement prévisibles par le fabricant.
La présente Norme européenne ne s'applique pas aux presses à filer qui ont été fabriquées avant sa date de publication comme EN.
Varnost strojev - Varnostne zahteve za stiskalnice za iztiskanje jekla in nekovinskih materialov
Ta evropski standard velja za: - stiskalnice na izhodni strani grelca s povezano opremo za premikanje, hlajenje in gašenje, ki vključuje npr. vlačilec, vročo žago, linijo, nosilnik, hladno žago, linijo za hladno žago in/ali navijalnik, ko so vgrajeni v opremo, do točke, ko se stisnjeni proizvod preda opremi za pakiranje. Določa zdravstvene in varnostne zahteve za vse stopnje v življenjski dobi opreme, njeno zasnovo, naročanje, konstrukcijo, uporabo in odlaganje. Ta evropski standard določa zahteve, ki jih mora izpolnjevati proizvajalec, da zagotavlja zdravje in varnost oseb med konstrukcijo, prevozom, usposobitvijo za zagon, delovanjem, vzdrževanjem in izločitvijo iz uporabe ter v primeru predvidljivih napak, kot so okvare opreme. Ta evropski standard obravnava vse bistvene nevarnosti, nevarne situacije in dogodke, pomembne za stiskalnice za iztiskanje, ko se uporabljajo kot predvideno in pod pogoji, ki jih proizvajalec lahko upravičeno predvidi. Ta evropski standard ne velja za stiskalnice za iztiskanje, izdelane pred datumom njegove objave kot EN.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Varnost strojev - Varnostne zahteve za stiskalnice za iztiskanje jekla in nekovinskih materialovSicherheit von Maschinen - Sicherheitsanforderungen an Strangpressen für Stahl und NE-MetalleSécurité des machines - Exigences de sécurité pour presses à filer l'acier et les métaux non ferreuxSafety of machinery - Safety requirements for extrusion presses for steel and non-ferrous metals25.120.10Kovaški stroji. Stiskalnice. ŠkarjeForging equipment. Presses. Shears13.110Varnost strojevSafety of machineryICS:Ta slovenski standard je istoveten z:EN 14656:2006+A1:2010SIST EN 14656:2007+A1:2010en,fr01-junij-2010SIST EN 14656:2007+A1:2010SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14656:2006+A1
April 2010 ICS 25.120.10 Supersedes EN 14656:2006English Version
Safety of machinery - Safety requirements for extrusion presses for steel and non-ferrous metals
Sécurité des machines - Exigences de sécurité pour presses à filer l'acier et les métaux non ferreux
Sicherheit von Maschinen - Sicherheitsanforderungen an Strangpressen für Stahl und NE-Metalle This European Standard was approved by CEN on 4 September 2006 and includes Amendment 1 approved by CEN on 28 February 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14656:2006+A1:2010: ESIST EN 14656:2007+A1:2010
Safety requirements for hydraulic, pressure water and lubrication systems . 32Annex B (normative)
!Safety requirements and/or measures for electrical equipment and control systems for extrusion presses" . 38Annex C (normative)
Noise test code . 42Annex D (informative)
De-commissioning . 47Annex ZA (informative)
!Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC" . 48Bibliography . 49 Figures Figure A.1 — Detail of the hydraulic diagram for limitation of set-up speed . 34 Figure C.1 — Example of measuring points for noise measurement (location of workstations) . 45
Tables Table B.1 — Emergency functions for extrusion presses . 40 Table C.1 — Example of declared dual-number noise values . 46 SIST EN 14656:2007+A1:2010
1 Scope This European Standard applies to: extrusion presses from the exit side of the heater through associated handling, cooling and quenching equipment including, e.g. the puller, the hot saw, the run-out table, the stretcher, the cold saw, cold saw table and/or coiler when incorporated into the equipment, to a point where the extruded product is passed to associated finishing equipment. It specifies the health and safety requirements at all stages in the life of the equipment, its design, ordering, construction, use and disposal. This European Standard specifies requirements to be met by the manufacturer to ensure the health and safety of persons during construction, transport, commissioning, operation, maintenance and de-commissioning, as well as in the event of foreseeable faults as malfunctions which may occur in the equipment. This European Standard deals with all significant hazards, hazardous situations and events relevant to extrusion presses when they are used as intended and under conditions which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard is not applicable to extrusion presses which are manufactured before the date of its publication as EN. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. !EN 349, Safety of machinery — Minimum gaps to avoid crushing of parts of the human body EN 614-1, Safety of machinery — Ergonomic design principles — Part 1: Terminology and general principles EN 614-2, Safety of machinery — Ergonomic design principles — Part 2: Interactions between the design of machinery and work tasks EN 626-1, Safety of machinery — Reduction of risks to health from hazardous substances emitted by machinery — Part 1: Principles and specifications for machinery manufacturers EN 842, Safety of machinery — Visual danger signals — General requirements, design and testing EN 894-1, Safety of machinery — Ergonomics requirements for the design of displays and control actuators — Part 1: General principles for human interactions with displays and control actuators EN 894-2, Safety of machinery — Ergonomics requirements for the design of displays and control actuators — Part 2: Displays EN 894-3, Safety of machinery — Ergonomics requirements for the design of displays and control actuators — Part 3: Control actuators EN 953:1997, Safety of machinery — Guards — General requirements for the design and construction of fixed and movable guards EN 981:1996, Safety of machinery — System of auditory and visual danger and information signals SIST EN 14656:2007+A1:2010
(IEC 60528-1:2007) SIST EN 14656:2007+A1:2010
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.