Conveyor belts - Adhesion between constitutive elements - Test methods (ISO 252:2007)

ISO 252:2007 specifies two test methods, A and B, for determining the adhesion strength between constitutive elements of a conveyor belt, i.e. between plies and between covers and carcass. Basic test conditions are in conformity with ISO 36.
It is applicable to all types of construction of conveyor belting with the exception of belts containing steel cord reinforcement, and textile-reinforced belts with a full-thickness tensile strength of less than 160 N/mm. It is not suitable or valid for light conveyor belts as described in ISO 21183-1.

Fördergurte - Lagenhaftung zwischen den Bestandteilen - Prüfverfahren (ISO 252:2007)

Diese Norm legt zwei Prüfverfahren, A und B, zur Bestimmung des Trennwiderstands zwischen den Lagen sowie zwischen den Deckplatten und der Karkasse von Fördergurten fest. Die wesentlichen Bedingungen der Prüfung entsprechen ISO 36.
Die Norm ist auf alle Arten von Fördergurten anwendbar, mit Ausnahme von Gurten mit Stahlseileinlagen und von Gurten mit Textileinlage, deren Nennbruchkraft weniger als 160 N/mm beträgt. Sie ist nicht anwendbar oder gültig für leichte Fördergurte nach ISO 21183-1
ANMERKUNG   Verfahren A oder Verfahren B können alter¬nativ angewendet werden, aber die berechneten Mittel¬werte für die Haftfestigkeit können für Verfahren A und Verfahren B unterschiedlich sein. Da auch beide Verfah¬ren nicht gleichwertig anwendbar sind für alle Gurtkon¬struktionen, sollte der Rat des Gurtherstellers eingeholt werden.

Courroies transporteuses - Adhérence entre éléments constitutifs - Méthodes d'essai (ISO 252:2007)

L'ISO 252:2007 spécifie deux méthodes d'essai, A et B, permettant de déterminer l'adhérence entre éléments constitutifs d'une courroie transporteuse, c'est-à-dire entre plis et entre revêtements et carcasse. Les conditions générales d'essai sont conformes à l'ISO 36.
Elle s'applique à tous types de construction de courroie transporteuse à l'exception des courroies à armature en câble d'acier, et des courroies à armature textile présentant une résistance à la rupture inférieure à 160 N/mm. Elle n'est pas applicable ou valable pour les courroies transporteuses légères décrites dans l'ISO 21183-1.

Naprave za kontinuirni transport - Trakovi tračnih transporterjev - Sprijetost osnovnih sestavnih elementov - Preskusne metode (ISO 252:2007)

General Information

Status
Published
Publication Date
14-Jun-2007
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Due Date
15-Jun-2007
Completion Date
15-Jun-2007

RELATIONS

Buy Standard

Standard
EN ISO 252:2008
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN ISO 252:2008
01-maj-2008
1DSUDYH]DNRQWLQXLUQLWUDQVSRUW7UDNRYLWUDþQLKWUDQVSRUWHUMHY6SULMHWRVW
RVQRYQLKVHVWDYQLKHOHPHQWRY3UHVNXVQHPHWRGH ,62
Conveyor belts - Adhesion between constitutive elements - Test methods (ISO
252:2007)

Fördergurte - Lagenhaftung zwischen den Bestandteilen - Prüfverfahren (ISO 252:2007)

Courroies transporteuses - Adhérence entre éléments constitutifs - Méthodes d'essai

(ISO 252:2007)
Ta slovenski standard je istoveten z: EN ISO 252:2007
ICS:
53.040.20
SIST EN ISO 252:2008 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN ISO 252
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2007
ICS 53.040.20 Supersedes EN ISO 252-1:1999
English Version
Conveyor belts - Adhesion between constitutive elements - Test
methods (ISO 252:2007)

Courroies transporteuses - Adhérence entre éléments Fördergurte - Lagenhaftung zwischen den Bestandteilen -

constitutifs - Méthodes d'essai (ISO 252:2007) Prüfverfahren (ISO 252:2007)
This European Standard was approved by CEN on 23 May 2007.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European

Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national

standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation

under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the

official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,

France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,

Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels

© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 252:2007: E

worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN ISO 252:2007 (E)
Foreword

This document (EN ISO 252:2007) has been prepared by Technical Committee ISO/TC 41

"Pulleys and belts (including veebelts)" in collaboration with Technical Committee CEN/TC 188

"Conveyor belts", the secretariat of which is held by BSI.

This European Standard shall be given the status of a national standard, either by publication of

an identical text or by endorsement, at the latest by December 2007, and conflicting national

standards shall be withdrawn at the latest by December 2007.
This document supersedes EN ISO 252-1:1999.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of

the following countries are bound to implement this European Standard: Austria, Belgium,

Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,

Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United

Kingdom.
Endorsement notice
The text of ISO 252:2007 has been approved by CEN as EN ISO 252:2007 without any
modifications.
---------------------- Page: 3 ----------------------
INTERNATIONAL ISO
STANDARD 252
Third edition
2007-06-15
Conveyor belts — Adhesion between
constitutive elements — Test methods
Courroies transporteuses — Adhérence entre éléments constitutifs —
Méthodes d'essai
Reference number
ISO 252:2007(E)
ISO 2007
---------------------- Page: 4 ----------------------
ISO 252:2007(E)
PDF disclaimer

This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but

shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In

downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat

accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.

Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation

parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In

the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

COPYRIGHT PROTECTED DOCUMENT
© ISO 2007

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,

electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or

ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
---------------------- Page: 5 ----------------------
ISO 252:2007(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies

(ISO member bodies). The work of preparing International Standards is normally carried out through ISO

technical committees. Each member body interested in a subject for which a technical committee has been

established has the right to be represented on that committee. International organizations, governmental and

non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the

International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards

adopted by the technical committees are circulated to the member bodies for voting. Publication as an

International Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. ISO shall not be held responsible for identifying any or all such patent rights.

ISO 252 was prepared by Technical Committee ISO/TC 41, Pulleys and belts (including veebelts),

Subcommittee SC 3, Conveyor belts.

This third edition of ISO 252 cancels and replaces ISO 252-1:1999, of which it constitutes a technical revision.

It also incorporates the Technical Corrigendum, ISO 252-1:1999/Cor. 1:2006.
© ISO 2007 – All rights reserved iii
---------------------- Page: 6 ----------------------
INTERNATIONAL STANDARD ISO 252:2007(E)
Conveyor belts — Adhesion between constitutive elements —
Test methods
1 Scope

This International Standard specifies two test methods, A and B, for determining the adhesion strength

between constitutive elements of a conveyor belt, i.e. between plies and between covers and carcass. Basic

test conditions are in conformity with ISO 36.

It is applicable to all types of construction of conveyor belting with the exception of belts containing steel cord

reinforcement, and textile-reinforced belts with a full-thickness tensile strength of less than 160 N/mm. It is not

[1]
suitable or valid for light conveyor belts as described in ISO 21183-1 .
NOTE Meth
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.