iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 494:2012/FprA1

(Amendment)

Fibre-cement profiled sheets and fittings - Product specification and test methods

Fibre-cement profiled sheets and fittings - Product specification and test methods

This European Standard specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement profiled sheets and their fibre-cement fittings for one or more the following uses:
- roofing;
- internal wall finishes;
- external wall and ceiling finishes.
For the purpose of this European Standard, fibre-cement profiles sheets are classified according to their height of corrugation and their mechanical characteristics.
This European Standard covers fibre-cement profiled sheets reinforced with fibres of different type as specified in  5.1.1, with and without facotory applied coating.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.
NOTE: Some of these requirements can be applied, after agreement, to curved sheets for specific applications

Faserzement-Wellplatten und dazugehörige Formteile - Produktspezifikation und Prüfverfahren

Plaques profilées en fibres-ciment et accessoires - Spécifications du produit et méthodes d'essai

Vlaknato-cementne valovite strešne plošče in fazonski kosi - Specifikacija za izdelek in preskusne metode

General Information

Status
Not Published
ICS
91.100.40 - Products in fibre-reinforced cement
Technical Committee
CEN/TC 128 - Roof covering products for discontinuous laying and products for wall cladding
Drafting Committee
CEN/TC 128/SC 4 - Fibre cement products for roofing
Current Stage
5060 - Closure of Vote - Formal Approval
Start Date
05-May-2015
Due Date
25-Mar-2016
Completion Date
05-May-2015
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
Mandate
M/121 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on internal and external wall and ceiling finishes
M/122 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on roof coverings, rooflights, roof windows and ancillary products
Ref Project
SIST EN 494:2013/kFprA1:2015 - Fibre-cement profiled sheets and fittings - Product specification and test methods

Relations

Merged Into
EN 494:2012+A1:2015 - Fibre-cement profiled sheets and fittings - Product specification and test methods
Effective Date
19-Jan-2023
Amends
EN 494:2012 - Fibre-cement profiled sheets and fittings - Product specification and test methods
Effective Date
16-Jul-2014

Buy Standard

EN 494:2013/kFprA1:2015EN 494:2013/kFprA1:2015
PreviousNext
Draft
EN 494:2013/kFprA1:2015
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 494:2013/kFprA1:2015
01-april-2015
9ODNQDWRFHPHQWQHYDORYLWHVWUHãQHSORãþHLQID]RQVNLNRVL6SHFLILNDFLMD]D
L]GHOHNLQSUHVNXVQHPHWRGH
Fibre-cement profiled sheets and fittings - Product specification and test methods
Faserzement-Wellplatten und dazugehörige Formteile - Produktspezifikation und
Prüfverfahren
Plaques profilées en fibres-ciment et accessoires - Spécifications du produit et méthodes
d'essai
Ta slovenski standard je istoveten z: EN 494:2012/FprA1
ICS:
91.060.20 Strehe Roofs
91.100.40 &HPHQWQLL]GHONLRMDþDQL] Products in fibre-reinforced
YODNQL cement
SIST EN 494:2013/kFprA1:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 494:2013/kFprA1:2015

---------------------- Page: 2 ----------------------

SIST EN 494:2013/kFprA1:2015

EUROPEAN STANDARD
FINAL DRAFT
EN 494:2012
NORME EUROPÉENNE

EUROPÄISCHE NORM
FprA1
February 2015
ICS 91.100.40
English Version
Fibre-cement profiled sheets and fittings - Product specification
and test methods
Plaques profilées en fibres-ciment et accessoires - Faserzement-Wellplatten und dazugehörige Formteile -
Spécifications du produit et méthodes d'essai Produktspezifikation und Prüfverfahren
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 128.

This draft amendment A1, if approved, will modify the European Standard EN 494:2012. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 494:2012/FprA1:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 494:2013/kFprA1:2015
EN 494:2012/FprA1:2015 (E)
Contents Page
Foreword .3
1 Modification to the Foreword .4
2 Modification to Clause 3, Terms and definitions .4
3 Modification to 5.2.2, Categorisation by height of profile .4
4 Modification to 5.2.3, Thickness .4
5 Modification to 5.3.3.2, Deflection .4
6 Modification to 5.6.3, Release of dangerous substances .4
7 Modification to Clause 6, Evaluation of conformity .4
8 Modification to 7.2.1.1.3.1, Measurement of the pitch a . 11
9 Modification to 7.2.1.1.3.2, Measurement of the height of corrugation h . 11
10 Modification to 7.2.1.2.3, Procedure . 11
11 Modification to 7.2.1.3.2, Apparatus .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 17468-1:2022(Main)
Fibre cement products - Determination of pull through and shear resistance and bending strength calculations - Part 1: Flat sheets
SIST EN 17468-1:2022

The document establishes an agreed method for evaluation of pull through resistance (tension/compression for fasteners through the sheets), shear resistance, bending strength and bending modulus of elasticity and suggests an approved safety concept of fibre-cement flat sheets for internal and external wall and ceiling finishes based on the experiences obtained over the last number of years in different countries. The results are only applicable to the fibre-cement product and not to the complete fixing assembly.
NOTE 1   For design purposes of fibre-cement flat sheets in the final application, the failure modes pull-out and breaking of the fixing or substructure are not in the scope of this standard. They might become decisive and need to be tested or calculated according to the relevant design standards for fixings (e.g. EN 14592) or ETA and substructure (e.g. Eurocode 3 for steel, Eurocode 5 for wood and Eurocode 9 for aluminium substructures) and compared with the results for pull-through and shear resistance.
The results are also applicable for:
—   Coated or uncoated sheets manufactured at the same production facility as the tested sheets provided that the sheets are of the same type, have at least the same declared class according to EN 12467:2012+A2:2018, Table 6 and at least the same nominal thickness.
—   The test method can be applied to textured or non-textured fibre-cement flat sheets. The results of non-textured sheets are only applicable for textured sheets if the nominal minimum thickness of the textured sheet is at least the nominal thickness of the non-textured sheet.
—   The same type of fixing head or washer assembly where applicable if the diameter of the fixing head or washer is 0 mm to 2 mm larger than in the test.
—   The Shore A hardness of the sealing washer, where applicable, is ± 5 that of the washer used in the test, given that the washer thickness is at least as thick, the washer material at least as strong and the shape (dome or flat) of the washer equal to what has been tested.
NOTE 2   
A)   For pull-through resistance, if the diameter of the drilled hole through the fibre-cement sheet is 0 mm to 2 mm smaller or equal than in the test up to the diameter of the shank of the fastener, providing, during the test there is the required clearance hole around the shank of the fastener.
B)   For shear resistance, if the diameter of the drilled hole is equal to what has been tested.
It applies only to products as delivered.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17468-2:2022(Main)
Fibre-cement products - Determination of pull through and shear resistance and bending strength calculations - Part 2: Profiled sheets
SIST EN 17468-2:2022

This document specifies test methods for pull through (tension/compression testing for fasteners through the sheets) and shear resistance of fibre-cement profiled sheets according to EN 494. The results are only applicable to the fibre-cement product and not to the complete fixing assembly.
It applies only to products as delivered.
The field of application for pull through resistance is defined in 7.6.
The field of application for shear resistance is defined in 8.6.
NOTE   For design purposes of fibre-cement profiled sheets in the final application, the failure modes pull-out and breaking of the fixings or substructure are not in the scope of this standard. They might become decisive and need to be tested or calculated according to the relevant design standards for fixings (e.g. Eurocode 3 for steel, Eurocode 5 for wood and Eurocode 9 for aluminium substructures) and compared with the results for pull-through and shear resistance.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 492:2012+A2:2018(Main)
Fibre-cement slates and fittings - Product specification and test methods
SIST EN 492:2013+A2:2018

This European Standard specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement slates and their fibre-cement fittings for one or more of the following uses:
-   roofing;
-   internal wall finishes;
-   external wall and ceiling finishes.
This European Standard applies to fibre-cement slates with a height dimension h (see Clause 4) not exceeding 850 mm for overlapping assembly. For the purpose of this European Standard, fibre-cement slates have been classified according to their bending moment.
This European Standard covers fibre-cement slates reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed products.

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12467:2012+A2:2018(Main)
Fibre-cement flat sheets - Product specification and test methods
SIST EN 12467:2013+A2:2018

This European Standard specifies the technical requirements and establishes methods of inspection and test as well as acceptance conditions for fibre-cement flat sheets, siding shingles and planks (referred to as sheets later in this document) for one or more of the following uses:
-   internal wall and ceiling finishes;
-   external wall and ceiling finishes.
Products covered by this European Standard can be used for other purposes provided they comply with the relevant application standard, e.g. rigid underlays.
This European Standard covers sheets reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not cover sheets for fire protection purposes.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.

  • Standard
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 494:2012+A1:2015(Main)
Fibre-cement profiled sheets and fittings - Product specification and test methods
SIST EN 494:2013+A1:2015

This European Standard specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement profiled sheets and their fibre-cement fittings for one or more of the following uses:
-   roofing;
-   internal wall finishes;
-   external wall and ceiling finishes.
For the purpose of this European Standard, fibre-cement profiled sheets are classified according to their height of corrugation and their mechanical characteristics.
This European Standard covers fibre-cement profiled sheets reinforced with fibres of different type as specified in 5.1.1, with and without factory applied coating.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.
NOTE   Some of these requirements can be applied, after agreement, to curved sheets for specific applications.

  • Standard
    71 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15057:2006(Main)
Fibre cement profiled sheets - Impact resistance test method
SIST EN 15057:2006

This European Standard specifies a soft body impact test method for fibre-cement profiled sheets for roofing.
This European Standard applies to fibre-cement profiled sheets conforming to EN 494 and of length greater than or equal to 1,04 m.
It applies only to products as delivered.
NOTE   This European Standard can be applied, after agreement between manufacturer and purchaser, to curved sheets.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12467:2012+A1:2016/prA2(Amendment)
Fibre-cement flat sheets - Product specification and test methods
SIST EN 12467:2013+A1:2016/oprA2:2017

This European Standard specifies the technical requirements and establishes methods of inspection and test as well as acceptance conditions for fibre-cement flat sheets, siding shingles and planks (referred to as sheets later in this document) for one or more of the following uses:
-   internal wall and ceiling finishes;
-   external wall and ceiling finishes.
Products covered by this European Standard can be used for other purposes provided they comply with the relevant application standard, e.g. rigid underlays.
This European Standard covers sheets reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not cover sheets for fire protection purposes.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.

  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 492:2012/FprA1:2015(Amendment)
Fibre-cement slates and fittings - Product specification and test methods
SIST EN 492:2013/kFprA1:2015

This European Standard specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement slates and their fibre-cement fittings for one or more of the following uses:
- roofing
- internal wall finishes
- external and ceiling finishes.
This European Standard applies to fibre-cement slates with a height dimension h (see Clause 4) not exceeding 850 mm for overlapping assembly. For the purpose of this European Standard, fibre-cement slates have been classified according to their bending moment.
This European Standard covers fibre-cement slates reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed products.

  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12467:2012/FprA1:2015(Amendment)
Fibre-cement flat sheets - Product specification and test methods
SIST EN 12467:2013/kFprA1:2015

This European Standard specifies the technical requirements and establishes methods of inspection and test as well as acceptance conditions for fibre-cement flat sheets, siding shingles and planks (referred to as sheets later in this document) for one or more of the following uses:
- internal wall and ceiling finishes,
- external wall and ceiling finishes.
Products covered by this European Standard can be used for other purposes provided they comply with the relevant application standard, e.g. rigid underlays.
This European Standard covers sheets reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not cover sheets for fire protection purposes.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.

  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17468-1:2022(Main)
Fibre cement products - Determination of pull through and shear resistance and bending strength calculations - Part 1: Flat sheets
SIST EN 17468-1:2022

The document establishes an agreed method for evaluation of pull through resistance (tension/compression for fasteners through the sheets), shear resistance, bending strength and bending modulus of elasticity and suggests an approved safety concept of fibre-cement flat sheets for internal and external wall and ceiling finishes based on the experiences obtained over the last number of years in different countries. The results are only applicable to the fibre-cement product and not to the complete fixing assembly.
NOTE 1   For design purposes of fibre-cement flat sheets in the final application, the failure modes pull-out and breaking of the fixing or substructure are not in the scope of this standard. They might become decisive and need to be tested or calculated according to the relevant design standards for fixings (e.g. EN 14592) or ETA and substructure (e.g. Eurocode 3 for steel, Eurocode 5 for wood and Eurocode 9 for aluminium substructures) and compared with the results for pull-through and shear resistance.
The results are also applicable for:
—   Coated or uncoated sheets manufactured at the same production facility as the tested sheets provided that the sheets are of the same type, have at least the same declared class according to EN 12467:2012+A2:2018, Table 6 and at least the same nominal thickness.
—   The test method can be applied to textured or non-textured fibre-cement flat sheets. The results of non-textured sheets are only applicable for textured sheets if the nominal minimum thickness of the textured sheet is at least the nominal thickness of the non-textured sheet.
—   The same type of fixing head or washer assembly where applicable if the diameter of the fixing head or washer is 0 mm to 2 mm larger than in the test.
—   The Shore A hardness of the sealing washer, where applicable, is ± 5 that of the washer used in the test, given that the washer thickness is at least as thick, the washer material at least as strong and the shape (dome or flat) of the washer equal to what has been tested.
NOTE 2   
A)   For pull-through resistance, if the diameter of the drilled hole through the fibre-cement sheet is 0 mm to 2 mm smaller or equal than in the test up to the diameter of the shank of the fastener, providing, during the test there is the required clearance hole around the shank of the fastener.
B)   For shear resistance, if the diameter of the drilled hole is equal to what has been tested.
It applies only to products as delivered.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day