EN ISO 11127-5:2011

Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 5: Determination of moisture (ISO 11127-5:2011)

ISO 11127-5:2011 specifies a method for the determination of the level of free moisture present in non-metallic blast-cleaning abrasives. It is determined by measuring the mass lost on heating.

Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen - Prüfverfahren für nichtmetallische Strahlmittel - Teil 5: Bestimmung der Feuchte (ISO 11127-5:2011)

Dies ist ein Teil aus einer Reihe von Teilen der Norm ISO 11127, welche die Probenahme und die Prüfung
von nichtmetallischen Strahlmitteln behandelt.
Die verschiedenen Arten nichtmetallischer Strahlmittel und Anforderungen an diese sind in den verschiedenen
Teilen von ISO 11126 enthalten.
Die Normenreihen ISO 11126 und ISO 11127 wurden als zusammengehöriger Satz von Internationalen
Normen über nichtmetallische Strahlmittel ausgearbeitet. Angaben über alle Teile der beiden Normenreihen
sind im Anhang A enthalten.
Dieser Teil von ISO 11127 legt ein Verfahren zur Bestimmung des Gehaltes an freier Feuchte in
nichtmetallischen Strahlmitteln fest. Der Gehalt an freier Feuchte wird aus dem Massenverlust beim Erhitzen
bestimmt.

Préparation des subjectiles d'acier avant application de peintures et de produits assimilés - Méthodes d'essai pour abrasifs non métalliques destinés à la préparation par projection - Partie 5 : Détermination de l'humidité (ISO 11127-5:2011)

L'ISO 11127-5:2011 spécifie une méthode pour la détermination de l'humidité présente dans les abrasifs non métalliques destinés à la préparation par projection. Elle est déterminée par mesurage de la perte de masse après chauffage.

Priprava jeklenih podlag pred nanašanjem barvnih in sorodnih premazov - Preskusne metode za nekovinske granulate za peskanje - 5. del: Ugotavljanje vlage (ISO 11127-5:2011)

To je eden od več delov standarda ISO 11127, ki obravnavajo vzorčenje in preskušanje nekovinskih granulatov. Vrste nekovinskega granulata in zahteve za vsak granulat določa standard ISO 11126. Skupini ISO 11126 in ISO 11127 sta bili pripravljeni kot skladen sklop mednarodnih standardov za nekovinske granulate za peskanje. Informacije o vseh delih obeh skupin so podane v dodatku A. Ta del standarda ISO 11127 določa metodo za ugotavljanje ravni proste vlage v nekovinskih granulatih za peskanje. Določi se z merjenjem mase, izgubljene zaradi ogrevanja.

General Information

• Status: Withdrawn
• Publication Date: 14-Dec-2011
• Withdrawal Date: 23-Feb-2021
• ICS: 25.220.10 - Surface preparation
• ICS: 87.020 - Paint coating processes
• Technical Committee: CEN/TC 139 - Paints and varnishes
• Drafting Committee: CEN/TC 139 - Paints and varnishes
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 24-Feb-2021
• Ref Project: SIST EN ISO 11127-5:2012 - Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 5: Determination of moisture (ISO 11127-5:2011)

Relations

• Replaces: EN ISO 11127-5:1997 - Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 5: Determination of moisture (ISO 11127-5:1993)
• Effective Date: 08-Jun-2022
• Replaced By: EN ISO 11127-5:2021 - Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 5: Determination of moisture (ISO 11127-5:2020)
• Effective Date: 02-Mar-2021

Standards Content (Sample)

SLOVENSKI STANDARD
01-februar-2012
1DGRPHãþD
SIST EN ISO 11127-5:1997
Priprava jeklenih podlag pred nanašanjem barvnih in sorodnih premazov -
Preskusne metode za nekovinske granulate za peskanje - 5. del: Ugotavljanje
vlage (ISO 11127-5:2011)
Preparation of steel substrates before application of paints and related products - Test
methods for non-metallic blast-cleaning abrasives - Part 5: Determination of moisture
(ISO 11127-5:2011)
Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen -
Prüfverfahren für nichtmetallische Strahlmittel - Teil 5: Bestimmung der Feuchte (ISO
11127-5:2011)
Préparation des subjectiles d'acier avant application de peintures et de produits
assimilés - Méthodes d'essai pour abrasifs non métalliques destinés à la préparation par
projection - Partie 5 : Détermination de l'humidité (ISO 11127-5:2011)
Ta slovenski standard je istoveten z: EN ISO 11127-5:2011
ICS:
25.220.10 Priprava površine Surface preparation
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 11127-5
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2012
ICS 25.220.10 Supersedes EN ISO 11127-5:1997
English Version
Preparation of steel substrates before application of paints and
related products - Test methods for non-metallic blast-cleaning
abrasives - Part 5: Determination of moisture (ISO 11127-
5:2011)
Préparation des subjectiles d'acier avant application de Vorbereitung von Stahloberflächen vor dem Auftragen von
peintures et de produits assimilés - Méthodes d'essai pour Beschichtungsstoffen - Prüfverfahren für nichtmetallische
abrasifs non métalliques destinés à la préparation par Strahlmittel - Teil 5: Bestimmung der Feuchte (ISO 11127-
projection - Partie 5 : Détermination de l'humidité (ISO 5:2011)
11127-5:2011)
This European Standard was approved by CEN on 14 December 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11127-5:2011: E
worldwide for CEN national Members.

Contents Page
Foreword .3

Foreword
This document (EN ISO 11127-5:2011) has been prepared by Technical Committee ISO/TC 35 "Paints and
varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2012, and conflicting national standards shall be withdrawn at
the latest by June 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11127-5:1997.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 11127-5:2011 has been approved by CEN as a EN ISO 11127-5:2011 without any
modification.
INTERNATIONAL  ISO
STANDARD 11127-5
Second edition
2011-12-15
Preparation of steel substrates before
application of paints and related
products — Test methods for non-
metallic blast-cleaning abrasives —
Part 5:
Determination of moisture
Préparation des subjectiles d’acier avant application de peintures et de
produits assimilés — Méthodes d’essai pour abrasifs non métalliques
destinés à la préparation par projection —
Partie 5: Détermination de l’humidité
Reference number
ISO 11127-5:2011(E)
©
ISO 2011
ISO 11127-5:2011(E)
©  ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved

ISO 11127-5:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organiz
...