EN ISO 10592:2022
(Main)Small craft - Remote hydraulic steering systems (ISO 10592:2022)
Small craft - Remote hydraulic steering systems (ISO 10592:2022)
This document specifies the requirements for the design, installation and testing of engine-mounted and craft-mounted remote hydraulic steering systems used with single and multiple engine installations of outboard engines over 15 kW per engine, as well as with single and multiple engines of inboard, sterndrive, and water jet drives, all used on small craft.
This document does not address emergency means of steering the craft.
Kleine Wasserfahrzeuge - Hydraulische Steueranlagen (ISO 10592:2022)
Dieses Dokument legt die Anforderungen an Entwurf, Einbau und Prüfungen von motorseitigen und fahrzeugseitigen hydraulischen Steueranlagen fest, die alle mit ein- oder mehrmotorigen Anlagen von Außenbordmotoren mit einer Leistung über 15 kW je Motor sowie ein- oder mehrmotorigen Anlagen mit Innenbordmotor, Z-Antrieb und Wasserstrahlantrieb an kleinen Wasserfahrzeugen verwendet werden.
Dieses Dokument behandelt keine Mittel zur Steuerung des Wasserfahrzeugs im Notfall (Notsteuerung).
Petits navires - Système de direction hydraulique commandé à distance (ISO 10592:2022)
Le présent document spécifie les exigences relatives à la conception, l’installation et aux essais des systèmes de direction hydrauliques commandés à distance, montés sur le moteur ou montés sur le bateau, utilisés dans les installations de moteurs hors-bord simples ou multiples, avec des moteurs hors-bord de plus de 15 kW par moteur, ainsi que dans les installations simples ou multiples de moteurs intérieurs, à embase arrière de transmission ou à propulsion par jet d’eau, utilisées sur les petits navires.
Ce document ne traite pas des dispositifs de barre de secours pour diriger le bateau.
Mala plovila - Daljinski hidravlični sistemi krmiljenja (ISO 10592:2022)
Ta dokument določa zahteve za projektiranje, vgradnjo in preskušanje daljinskih hidravličnih sistemov krmiljenja, nameščenih v motor in plovilo, ki se uporabljajo v sistemih z enim in več izvenkrmnimi motorji
z močjo posameznega motorja 15 kW, ter v sistemih vgrajenih, krmnih in vodnih reaktivnih pogonskih enot z enim in več motorji, ki se uporabljajo za mala plovila.
Ta dokument ne obravnava naprav za krmiljenje plovila v sili.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2022
Nadomešča:
SIST EN ISO 10592:2017
Mala plovila - Daljinski hidravlični sistemi krmiljenja (ISO 10592:2022)
Small craft - Remote hydraulic steering systems (ISO 10592:2022)
Kleine Wasserfahrzeuge - Hydraulische Steueranlagen (ISO 10592:2022)
Petits navires - Système de direction hydraulique commandé à distance (ISO
10592:2022)
Ta slovenski standard je istoveten z: EN ISO 10592:2022
ICS:
47.020.70 Navigacijska in krmilna Navigation and control
oprema equipment
47.080 Čolni Small craft
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 10592
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2022
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 10592:2017
English Version
Small craft - Remote hydraulic steering systems (ISO
10592:2022)
Petits navires - Système de direction hydraulique Kleine Wasserfahrzeuge - Hydraulische Steueranlagen
commandé à distance (ISO 10592:2022) (ISO 10592:2022)
This European Standard was approved by CEN on 3 May 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATIO N
EUROPÄISCHES KOMITEE FÜR NORMUN G
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10592:2022 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered . 4
European foreword
This document (EN ISO 10592:2022) has been prepared by Technical Committee ISO/TC 188 "Small
craft" in collaboration with Technical Committee CEN/TC 464 “Small Craft” the secretariat of which is
held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2023, and conflicting national standards shall
be withdrawn at the latest by January 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10592:2017.
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s) / Regulation(s).
For the relationship with EU Directive(s) / Regulation(s), see informative Annex ZA, which is an integral
part of this document.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 10592:2022 has been approved by CEN as EN ISO 10592:2022 without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered
This European Standard has been prepared under a Commission standardization request
M/542/C(2015) 8736 final to provide one voluntary means of conforming to essential requirements of
Directive 2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and
Annex I of Directive 2013/53/EU
Essential Requirements of Clause(s)/sub-clause(s) Remarks/Notes
Directive 2013/53/EU of this EN
Annex I, Clause 5.4.1, Steering 4, 5, 6, 7, 8, 9 and 11 This standard specifies the
system, general. requirements for remote
hydraulic steering systems from
the helm up to and including the
output device connection point.
This standard does not address
propulsion control systems
This standard does not address
an emergency mean of steering.
Annex I, Clause 2.5, Owner’s 10
Manual
Annex II, Components of 4, 5, 7, 9.3 and 11 In respect of hydraulic steering
watercraft (3) Steering wheels, mechanisms supplied as
steering mechanisms and cable components only.
assemblies.
Steering wheels and cable
assemblies supplied as
components are excluded from
this standard.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
INTERNATIONAL ISO
STANDARD 10592
Second edition
2022-06
Small craft — Remote hydraulic
steering systems
Petits navires — Système de direction hydraulique commandé à
distance
Reference number
ISO 10592:2022(E)
ISO 10592:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 10592:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 4
5 Materials . 7
6 Outboard engines and sterndrives. 7
7 Steering system requirements .13
8 Installation .14
9 Test requirements .18
9.1 Installed proof tests . 18
9.2 System application tests . 18
9.3 Steering system components tests . 18
10 Owner’s manual .21
11 Installation manual .22
Bibliography .23
iii
ISO 10592:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 188, Small craft, in collaboration with
the European Committee for Standardization (CEN) Technical Committee CEN/TC 464, Small craft, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 10592:1994), which has been technically
revised.
The main changes are as follows:
— in Clause 3, definitions have been updated;
— throughout the text, requirements have been updated to meet the state of the art;
— the steering wheel requirements and tests have been removed;
— former Clause 12, Designation, has been removed.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
INTERNATIONAL STANDARD ISO 10592:2022(E)
Small craft — Remote hydraulic steeri
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.