EN ISO 8665-2:2024
(Main)Small craft - Power measurements and declarations - Part 2: Electric marine propulsion (ISO 8665-2:2024)
Small craft - Power measurements and declarations - Part 2: Electric marine propulsion (ISO 8665-2:2024)
This document specifies the requirements for the determination of the power of electric marine propulsion systems when presented for documenting and checking of the declared (rated) power published by the manufacturer.
This document is applicable to electric systems used for propulsion of recreational craft and other small craft of up to 24 m of hull length.
Kleine Wasserfahrzeuge - Leistungsmessungen und -Leistungsangaben - Teil 2: Elektrischer Schiffsantrieb (ISO 8665-2:2024)
Dieses Dokument legt die Anforderungen für die Bestimmung der Leistung von elektrischen Schiffsantriebssystemen zum Zweck der Dokumentation und Prüfung der vom Hersteller erklärten (Bemessungs-)Leistung fest.
Dieses Dokument ist anwendbar auf elektrische Systeme, die für den Antrieb von Sportbooten und anderen kleinen Wasserfahrzeugen mit einer Rumpflänge von bis zu 24 m verwendet werden.
Petits navires - Mesurage et déclaration de la puissance - Partie 2: Propulsion électrique à usage marin (ISO 8665-2:2024)
Le présent document spécifie les exigences liées à la détermination de la puissance des systèmes de propulsion électrique à usage marin lors de la documentation et de la vérification de la puissance (nominale) déclarée publiée par le fabricant.
Le présent document s’applique aux systèmes électriques utilisés pour la propulsion de bateaux de plaisance et autres petits navires d’une longueur de coque maximale de 24 m.
Mala plovila - Merjenje moči in deklariranje - 2. del: Električni pogon plovil (ISO 8665-2:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2024
Mala plovila - Merjenje moči in deklariranje - 2. del: Električni pogon plovil (ISO
8665-2:2024)
Small craft - Power measurements and declarations - Part 2: Electric marine propulsion
(ISO 8665-2:2024)
Kleine Wasserfahrzeuge - Leistungsmessungen und ‑Leistungsangaben - Teil 2:
Elektrischer Schiffsantrieb (ISO 8665-2:2024)
Petits navires - Mesurage et déclaration de la puissance - Partie 2: Propulsion électrique
à usage marin (ISO 8665-2:2024)
Ta slovenski standard je istoveten z: EN ISO 8665-2:2024
ICS:
47.020.20 Ladijski motorji Marine engines and
propulsion systems
47.080 Čolni Small craft
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 8665-2
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2024
EUROPÄISCHE NORM
ICS 47.080
English Version
Small craft - Power measurements and declarations - Part
2: Electric marine propulsion (ISO 8665-2:2024)
Petits navires - Mesurage et déclaration de la puissance Kleine Wasserfahrzeuge - Leistungsmessungen und -
- Partie 2: Propulsion électrique à usage marin (ISO Leistungsangaben - Teil 2: Elektrischer Schiffsantrieb
8665-2:2024) (ISO 8665-2:2024)
This European Standard was approved by CEN on 17 May 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8665-2:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered . 4
European foreword
This document (EN ISO 8665-2:2024) has been prepared by Technical Committee ISO/TC 188 "Small
craft" in collaboration with Technical Committee CEN/TC 464 “Small Craft” the secretariat of which is
held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2024, and conflicting national standards
shall be withdrawn at the latest by December 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document is a new second part of ISO 8665 series on "Small craft -Power measurement and
declaration.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this
document.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 8665-2:2024 has been approved by CEN as EN ISO 8665-2:2024 without any
modification.
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered
This European Standard has been prepared under a Commission’s standardization request
M/542/C(2015) 8736 final to provide one voluntary means of conforming to essential requirements of
Directive 2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and
Annex of Directive 2013/53/EU
Essential Requirements of Clause(s)/subclause(s) Remarks/Notes
Directive 2013/53/EU of this EN
Annex I.A.4 – Handling Clause 4 This standard does not cover
Characteristics; only in respect of testing to determine if a
the maximum rated propulsion watercraft has satisfactory
engine power. handling characteristics.
Propulsion system power of
electric motors shall be
measured in accordance to this
document.
It should be noted that I.A.4
requires that the maximum rated
power for all propulsion systems
shall be declared in the owner’s
manual.
Annex I.A, 2.5 Owner’s manual Clause 4 The electric motors propulsion
system shall be declared in the
owner’s manual
Annex IV EU declaration of Clause 4 The electric motors propulsion
conformity system where required by the
Declaration of conformity agreed
by AdCo
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
International
Standard
ISO 8665-2
First edition
Small craft — Power measurements
2024-05
and declarations —
Part 2:
Electric marine propulsion
Petits navires — Mesurage et déclaration de la puissance —
Partie 2: Propulsion électrique à usage marin
Reference number
ISO 8665-2:2024(en) © ISO 2024
ISO 8665-2:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 8665-2:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Declaration of power . 2
4.1 General .2
4.2 Declaration of propeller shaft power .2
4.3 Declaration of motor power .2
5 Test methods . 2
5.1 Test conditions .2
5.2 Production conformity test/manufacturing tolerance .3
6 Test report . 3
Bibliography . 5
iii
ISO 8665-2:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 188, Small craft, in collaboration with
the European Committee for Standardization (CEN) Technical Committee CEN/TC 464, Small Craft, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
A list of all parts in the ISO 8665 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.