iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 13523-6:2020

(Main)

Coil coated metals - Test methods - Part 6: Adhesion after indentation (cupping test)

Coil coated metals - Test methods - Part 6: Adhesion after indentation (cupping test)

This document defines terms of the procedure for determining the adhesion of an organic coating to a metallic substrate after indentation produced by slow deformation.
The resistance to cracking can also be evaluated.

Bandbeschichtete Metalle - Prüfverfahren - Teil 6: Haftfestigkeit nach Eindrücken (Tiefungsprüfung)

Dieses Dokument legt das Verfahren zum Bestimmen der Haftfestigkeit einer organischen Beschichtung auf einem metallischen Substrat nach Eindrücken bei langsamer Verformung fest.
Die Widerstandsfähigkeit gegen Rissbildung kann auch bewertet werden.

Tôles prélaquées - Méthodes d’essai - Partie 6 : Adhérence après indentation (essai d’emboutissage)

Le présent document décrit le mode opératoire de détermination de l’adhérence d’un revêtement organique sur un subjectile métallique après indentation provoquée par déformation lente.
La résistance à la fissuration peut également être évaluée.

Prevlečene kovine, ki se navijajo - Preskusne metode - 6. del: Oprijem po globljenju (preskus elastičnosti)

General Information

Status
Published
Publication Date
02-Jun-2020
Withdrawal Date
30-Dec-2020
ICS
25.220.60 - Organic coatings
Technical Committee
CEN/TC 139 - Paints and varnishes
Drafting Committee
CEN/TC 139/WG 9 - Testing of coil coated metals
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
03-Jun-2020
Due Date
01-Jun-2021
Completion Date
03-Jun-2020
Ref Project
SIST EN 13523-6:2020 - Coil coated metals - Test methods - Part 6: Adhesion after indentation (cupping test)

Relations

Replaces
EN 13523-6:2002 - Coil coated metals - Test methods - Part 6: Adhesion after indentation (cupping test)
Effective Date
08-Jun-2022

Buy Standard

EN 13523-6:2020EN 13523-6:2020
PreviousNext
Standard
EN 13523-6:2020
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 13523-6:2020
01-september-2020
Nadomešča:
SIST EN 13523-6:2003
Prevlečene kovine, ki se navijajo - Preskusne metode - 6. del: Oprijem po
globljenju (preskus elastičnosti)
Coil coated metals - Test methods - Part 6: Adhesion after indentation (cupping test)
Bandbeschichtete Metalle - Prüfverfahren - Teil 6: Haftfestigkeit nach Eindrücken
(Tiefungsprüfung)
Tôles prélaquées - Méthodes d'essai - Partie 6 : Adhérence après indentation (essai
d'emboutissage)
Ta slovenski standard je istoveten z: EN 13523-6:2020
ICS:
25.220.60 Organske prevleke Organic coatings
SIST EN 13523-6:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 13523-6:2020

---------------------- Page: 2 ----------------------
SIST EN 13523-6:2020


EN 13523-6
EUROPEAN STANDARD

NORME EUROPÉENNE

June 2020
EUROPÄISCHE NORM
ICS 25.220.60 Supersedes EN 13523-6:2002
English Version

Coil coated metals - Test methods - Part 6: Adhesion after
indentation (cupping test)
Tôles prélaquées - Méthodes d'essai - Partie 6 : Bandbeschichtete Metalle - Prüfverfahren - Teil 6:
Adhérence après indentation (essai d'emboutissage) Haftfestigkeit nach Eindrücken (Tiefungsprüfung)
This European Standard was approved by CEN on 3 May 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13523-6:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 13523-6:2020
EN 13523-6:2020 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Apparatus and materials . 5
6 Sampling . 6
7 Test panels . 6
8 Procedure. 6
8.1 Ambient conditions . 6
8.2 Cross-hatching (not used for evaluation of resistance to cracking) . 6
8.2.1 For coatings greater than or equal to 60 µm thickness (see Figure 1) . 6
8.2.2 For coatings less than 60 µm thickness (see Figure 2) . 7
8.3 Pressing .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 13523-23:2023(Main)
Coil coated metals - Test methods - Part 23: Resistance to humid atmospheres containing sulfur dioxide
SIST EN 13523-23:2023

This document describes the procedure for determining the resistance of an organic coating on a metallic substrate to humid atmospheres containing sulfur dioxide.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-14:2023(Main)
Coil coated metals - Test methods - Part 14: Chalking (Helmen method)
SIST EN 13523-14:2023

This document describes the procedure for determining objectively the chalking resulting from natural or artificial weathering of an organic coating on a metallic substrate.
The advantage of this procedure for measuring chalking of an organic coating is that the result can be read off immediately on an instrument. Subjective judgement by visual comparison of test specimens with reference specimens is not necessary.
Reproducible results can only be obtained by careful execution of the test. Special attention is paid to the adhesive tape and its application to the test surface.
The test method is not applicable to embossed coatings. In the case of textured coatings, the degree of texture will influence readings. Also, dirt collection can influence readings on outdoor weathered specimens.
NOTE   Different methods for assessing chalking are in use. The results of these different methods are not comparable.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-26:2022(Main)
Coil coated metals - Test methods - Part 26: Resistance to condensation of water
SIST EN 13523-26:2022

This document specifies a procedure for evaluating the resistance to continuous condensation of an organic coating on a metallic substrate, by means of exposure in a humidity cabinet under controlled conditions.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-9:2022(Main)
Coil coated metals - Test methods - Part 9: Resistance to water immersion
SIST EN 13523-9:2022

This document specifies the procedure for determining the resistance to water immersion of an organic coating on a metallic substrate.
The test is applicable to all kinds of organic coatings, including metallics and embossed, textured, pearlescent and printed coatings. The results of the test give an indication of the resistance of the coil coated metal to water.
The method is not intended to reproduce any particular condition of condensation.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-25:2022(Main)
Coil coated metals - Test methods - Part 25: Resistance to humidity
SIST EN 13523-25:2022

This document specifies a procedure for evaluating the resistance to humidity of an organic coating on a metallic substrate, by means of exposure in a humidity cabinet under controlled conditions.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-2:2021(Main)
Coil coated metals - Test methods - Part 2: Gloss
SIST EN 13523-2:2021

This document specifies the procedure for determining the gloss of an organic coating on a metallic substrate. Gloss is a characteristic of fundamental importance to the appearance of the coil coated product.
The apparatus requires a flat specimen of size greater than the aperture, thus, uneven surfaces cannot be measured.
This method is applicable to all pigmented and unpigmented coatings including metallic/pearlescent coatings. However, for textured coatings it is only indicative.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-0:2021(Main)
Coil coated metals - Test methods - Part 0: General introduction
SIST EN 13523-0:2021

This document specifies the overall scope of all parts of EN 13523, gives definitions common to all parts and describes how sampling and preparation of test panels for most of the individual test methods are to be carried out.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-3:2021(Main)
Coil coated metals - Test methods - Part 3: Colour difference and metamerism - Instrumental comparison
SIST EN 13523-3:2021

This document specifies procedures for determining the instrumental colour difference (CIELAB) of an organic coating on a metallic substrate compared to another one used as a reference (usually called reference) and the metamerism depending on the illuminant.
When two colour specimens have identical spectral reflectance curves, they are matching under any illuminant irrespective of its spectral characteristics. This is termed a “spectral match”. It is also possible for two colour specimens having different spectral reflectance curves to match visually under a given light source but not to match under another light source with different spectral characteristics; such matches are termed “metameric”.
One quantitative description of metamerism is the so-called “metamerism index”.
Information on the metamerism index is of limited value where ΔE (instrumental colour difference for a given illuminant) is > 0,5. The metamerism index is not suited for determining the absolute colour difference or colour consistency of a given specimen at change of illuminant.
The colour difference under the reference illuminant is to be measured in colour coordinates L*, a* and b*.
Excluded from this method are organic coatings producing fluorescence and/or which are multicoloured, pearlescent or metallic.
Establishing a reference as well as the magnitude of an acceptable colour difference are not covered by this method.
Two methods are given in this document:
a)   instrumental colour difference measurement using a tristimulus colourimeter;
b)   instrumental colour difference measurement using a spectrophotometer or equivalent.
It is advised that care is taken when measuring e.g.
—   textured surfaces;
—   fluorescent coatings;
—   metameric coatings;
—   multi-coloured, pearlescent, metallic or special colour effect coatings.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-7:2021(Main)
Coil coated metals - Test methods - Part 7: Resistance to cracking on bending (T-bend test)
SIST EN 13523-7:2021

This document specifies the procedure for determining the resistance to cracking of an organic coating on a metallic substrate when bent through 135° to 180°. The degree of adhesion can also be evaluated.
Both folding and mandrel methods are considered. The folding method is more often used for practical purposes but where more precise determinations are required, the mandrel method is the preferred method.
The cylindrical bend method can also be used for a pass/fail decision by using an agreed mandrel.
The choice of the appropriate test method is limited by the thickness and/or the hardness of the substrate.
The feasibility of the test depends on the type and thickness of the substrate. During the procedure, the mandrel is not intended to deform.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-20:2020(Main)
Coil coated metals - Test methods - Part 20: Foam adhesion
SIST EN 13523-20:2020

This document describes a laboratory method for testing foam adhesion to an organic coating on a metallic substrate under dry and wet conditions.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day