FprEN 13480-9
(Main)Metallic industrial piping - Part 9: Additional requirements for nickel and nickel alloys piping
Metallic industrial piping - Part 9: Additional requirements for nickel and nickel alloys piping
This document specifies requirements for metallic industrial piping and their parts made of nickel and nickel alloys (see 3.1) in addition to the general requirements for metallic industrial piping under EN 13480 1:2017, EN 13480 2:2017, EN 13480 3:2017, EN 13480 4:2017 and EN 13480 5:2017.
NOTE Cast materials are not included in this version. Details regarding cast materials will be subject to an amendment to or a revision of this document.
Metallische industrielle Rohrleitungen - Teil 9: Zusatzanforderungen an Rohrleitungen aus Nickel und Nickellegierungen
Dieses Dokument legt zusätzlich zu den allgemeinen Anforderungen an metallische industrielle Rohrleitungen nach EN 13480 1:2017, EN 13480 2:2017, EN 13480 3:2017, EN 13480 4:2017 und EN 13480 5:2017 Anforderungen an aus Nickel und Nickellegierungen (siehe 3.1) hergestellte metallische industrielle Rohrleitungen und deren Bauteile fest.
ANMERKUNG Gusswerkstoffe sind in der vorliegenden Fassung nicht enthalten. Angaben zu Gusswerkstoffen werden in einer Änderung oder Überarbeitung dieses Dokument erfasst.
Tuyauteries industrielles métalliques - Partie 9 : Exigences complémentaires relatives aux tuyauteries en nickel et alliages de nickel
Le présent document définit les exigences relatives aux tuyauteries industrielles métalliques en nickel et alliages de nickel et à leurs parties (voir 3.1), en complément des exigences générales relatives aux tuyauteries industrielles métalliques des EN 13480 1:2017, EN 13480 2:2017, EN 13480 3:2017, EN 13480 4:2017 et EN 13480 5:2017.
NOTE La présente version ne traite pas des matériaux moulés. Les détails relatifs aux matériaux moulés feront l'objet d'un amendement ou d'une révision du présent document.
Kovinski industrijski cevovodi - 9. del: Dodatne zahteve za cevovode iz niklja in nikljevih zlitin
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2018
Kovinski industrijski cevovodi - 9. del: Dodatne zahteve za cevovode iz niklja in
nikljevih zlitin
Metallic industrial piping - Part 9: Additional requirements for nickel and nickel alloys
piping
Metallische industrielle Rohrleitungen - Teil 9: Zusatzanforderungen an Rohrleitungen
aus Nickel und Nickellegierungen
Tuyauteries industrielles métalliques - Partie 9 : Exigences complémentaires relatives
aux tuyauteries en nickel et alliages de nickel
Ta slovenski standard je istoveten z: prEN 13480-9
ICS:
23.040.15 Cevi iz neželeznih kovin Non-ferrous metal pipes
77.120.40 Nikelj, krom in njune zlitine Nickel, chromium and their
alloys
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
prEN 13480-9
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2018
ICS 23.040.15
English Version
Metallic industrial piping - Part 9: Additional requirements
for nickel and nickel alloys piping
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 267.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13480-9:2018 E
worldwide for CEN national Members.
prEN 13480-9:2018 (E)
Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General requirements . 5
5 Materials . 6
5.1 General. 6
5.2 Material grouping system . 6
5.3 Material documentation . 6
5.4 Prevention of brittle fracture . 6
5.5 Lamellar tearing . 6
6 Design . 6
6.1 General. 6
6.2 Time-independent nominal design stress . 7
6.3 Creep design . 7
6.4 Piping under external pressure . 7
6.5 Fatigue design . 7
7 Fabrication . 8
7.1 General. 8
7.2 Qualification of welding procedure specifications (WPQR) . 8
7.3 Qualification of welders and welding operators . 8
7.4 Joint preparation . 8
7.5 Preheat . 9
7.6 Forming procedures . 9
7.6.1 Cold forming . 9
7.6.2 Hot forming . 9
7.7 Heat treatment after forming . 9
7.7.1 General. 9
7.7.2 Heat treatment of flat products after cold forming . 9
7.7.3 Heat treatment of tubular products after cold forming . 10
7.7.4 Heat treatment after hot forming . 10
7.8 Sampling of formed products . 10
7.8.1 Cold formed products without heat treatment . 10
7.8.2 Hot formed or cold formed products with heat treatment . 10
7.9 Tests . 11
7.10 Post weld heat treatment (PWHT) . 11
7.11 Repairs . 11
8 Inspection and testing . 11
8.1 General. 11
8.2 Non-destructive testing of welded joints . 12
8.3 Selection of non destructive testing methods for surface imperfections . 12
Annex A (informative) Grouping system for nickel alloys . 13
Annex B (informative) Designations of some nickel alloys . 16
prEN 13480-9:2018 (E)
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2014/68/EU aimed to be covered . 21
Bibliography . 22
prEN 13480-9:2018 (E)
European foreword
This document (prEN 13480-9:2018) has been prepared by Technical Committee CEN/TC 267
“Industrial piping and pipelines”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
This European Standard EN 13480, Metallic industrial piping, consists of nine interdependent and not
dissociable parts which are:
— Part 1: General;
— Part 2: Materials;
— Part 3: Design and calculation;
— Part 4: Fabrication and installation;
— Part 5: Inspection and testing;
— Part 6: Additional requirements for buried piping;
— Part 7: Guidance on the use of conformity assessment procedures [CEN/TR];
— Part 8: Additional requirements for aluminium and aluminium alloy piping;
— Part 9: Additional requirements for nickel and nickel alloys piping.
Although these parts may be obtained separately, the parts are interdependent. As such the manufacture
of metallic industrial piping requires the application of all the relevant parts in order for the requirements
of the European Standard to be satisfactorily fulfilled.
This European Standard will be maintained by a Maintenance MHD working group whose scope of
working is limited to corrections and interpretations related to the EN 13480 series.
The contact to submit queries can be found at http://www.unm.fr (en13480@unm.fr). A form for
submitting questions can be downloaded from the link to the MHD website. After subject experts have
agreed an answer, the answer will be communicated to the questioner. Corrected pages will be given
specific issue number and issued by CEN according to CEN Rules. Interpretation sheets will be posted on
the website of the MHD.
prEN 13480-9:2018 (E)
1 Scope
This document specifies requirements for metallic industrial piping and their parts made of nickel and
nickel alloys (see 3.1) in addition to the general requirements for metallic industrial piping under
EN 13480-1:2017, EN 13480-2:2017, EN 13480-3:2017, EN 13480-4:2017 and EN 13480-5:2017.
NOTE Cast materials are not included in this version. Details regarding cast materials will be subject to an
amendment to or a revision of this document.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 764-5:2014, Pressure equipment – Part 5: Inspection documentation of metallic materials and
compliance with the material specification
EN 10204:2004, Metallic products - Types of inspection documents
EN 13480-1:2017, Metallic industrial piping – Part 1: General
EN 13480-2:2017, Metallic industrial piping – Part 2: Materials
EN 13480-3:2017, Metallic industrial piping – Part 3: Design and calculation
EN 13480-4:2017, Metallic industrial piping – Part 4: Fabrication and installation
EN 13480-5:2017, Metallic industrial piping – Part 5: Inspection and testing
EN 13445-3:2014, Unfired pressure vessels – Part 3: Design
EN ISO 9606-4:1999, Approval testing of welders - Fusion welding – Part 4: Nickel and nickel alloys
(ISO 9606-4:1999)
CEN ISO/TR 15608:2013, Welding - Guidelines for a metallic materials grouping system
(ISO/TR 15608:2013)
3 Terms and definitions
For the purposes of this document, the terms, definitions, symbols and units given in EN 13480-1:2017,
EN 13480-2:2017, EN 13480-3:2017, EN 13480-4:2017 and EN 13480-5:2017 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
nickel alloys
alloys which contain a minimum of 30 % nickel and contain more nickel than iron
4 General requirements
The general requirements of EN 13480-1:2017 shall apply.
prEN 13480-9:2018 (E)
5 Materials
5.1 General
The general requirements of EN 13480-2:2017 shall apply with the following additions/exclusions in 5.2-
5.5.
NOTE There are presently no European Standards specifically for nickel or nickel alloys for pressure purposes.
This document is therefore limited to:
1) Harmonized standards as listed in Table A.2;
2) Nickel and nickel alloys having EMAs as listed in Table A.3;
These comm
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.