Technical product documentation (TPD) - General principles of representation - Part 1: Introduction and fundamental requirements (ISO 128-1:2020)

This document gives general rules for the execution of technical drawings (2D and 3D), as well as presenting the structure of the other parts of the ISO 128 series. This document is applicable to technical drawing in the fields of mechanical engineering, construction, architecture and shipbuilding. It is applicable to both manual and computer-based technical drawings.
For the purpose of this document the term "technical drawing" shall be interpreted in the broadest possible sense, encompassing the total package of documentation specifying the product (workpiece, subassembly, assembly).

Technische Produktdokumentation (TPD) - Allgemeine Grundlagen der Darstellung - Teil 1: Einleitung und grundlegende Anforderungen (ISO 128-1:2020)

Dieses Dokument enthält allgemeine Regeln für die Ausführung von technischen Zeichnungen (2D und 3D) sowie die Darstellung zum Aufbau aller anderen Teile von ISO 128. Dieses Dokument ist anwendbar für technische Zeichnungen in den Bereichen mechanische Technik, Bauwesen, Architektur und Schiffbau. Es ist sowohl für manuelle als auch rechnergestützt erstellte technische Zeichnungen anwendbar.
Für die Anwendung dieses Dokuments muss der Begriff „technische Zeichnung“ so allgemein wie möglich ausgelegt werden und sämtliche Dokumentation zum Produkt umfassen (Werkstück, Unterbaugruppe, Baugruppe).

Documentation technique de produits (TPD) - Principes généraux de représentation - Partie 1: Introduction et exigences fondamentales (ISO 128-1:2020)

Le présent document donne les règles générales d'exécution des dessins techniques (2D et 3D), ainsi que la structure des autres parties de la série ISO 128. Le présent document est applicable aux dessins techniques dans le domaine de la construction mécanique, de la construction et du génie civil, de l'architecture et de la construction navale. Elle s'applique aussi bien aux dessins réalisés manuellement qu'à ceux réalisés par ordinateur.
Pour les besoins du présent document le terme «dessin technique» doit être interprétée dans le sens le plus large possible, qui englobe l'ensemble de la documentation spécifiant le produit (pièce, sous-assemblage, assemblage).

Tehnična dokumentacija izdelkov - Splošna načela predstavitve - 1. del: Uvod in temeljne zahteve (ISO 128-1:2020)

General Information

Status
Published
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Due Date
10-Jun-2020
Completion Date
10-Jun-2020

Buy Standard

Standard
EN ISO 128-1:2020
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN ISO 128-1:2020
01-september-2020
Tehnična dokumentacija izdelkov - Splošna načela predstavitve - 1. del: Uvod in
temeljne zahteve (ISO 128-1:2020)

Technical product documentation (TPD) - General principles of representation - Part 1:

Introduction and fundamental requirements (ISO 128-1:2020)

Technische Produktdokumentation (TPD) - Allgemeine Grundlagen der Darstellung - Teil

1: Einleitung und grundlegende Anforderungen (ISO 128-1:2020)

Documentation technique de produits (TPD) - Principes généraux de représentation -

Partie 1: Introduction et exigences fondamentales (ISO 128-1:2020)
Ta slovenski standard je istoveten z: EN ISO 128-1:2020
ICS:
01.110 Tehnična dokumentacija za Technical product
izdelke documentation
SIST EN ISO 128-1:2020 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 128-1:2020
---------------------- Page: 2 ----------------------
SIST EN ISO 128-1:2020
EN ISO 128-1
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2020
EUROPÄISCHE NORM
ICS 01.100.01
English Version
Technical product documentation (TPD) - General
principles of representation - Part 1: Introduction and
fundamental requirements (ISO 128-1:2020)

Documentation technique de produits (TPD) - Technische Produktdokumentation (TPD) - Allgemeine

Principes généraux de représentation - Partie 1: Grundlagen der Darstellung - Teil 1: Einleitung und

Introduction et exigences fondamentales (ISO 128- grundlegende Anforderungen (ISO 128-1:2020)

1:2020)
This European Standard was approved by CEN on 18 May 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 128-1:2020 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 128-1:2020
EN ISO 128-1:2020 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

---------------------- Page: 4 ----------------------
SIST EN ISO 128-1:2020
EN ISO 128-1:2020 (E)
European foreword

This document (EN ISO 128-1:2020) has been prepared by Technical Committee ISO/TC 10 "Technical

product documentation" in collaboration with Technical Committee CEN/SS F01 “Technical drawings”

the secretariat of which is held by CCMC.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by December 2020, and conflicting national standards

shall be withdrawn at the latest by December 2020.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,

Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of

North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the

United Kingdom.
Endorsement notice

The text of ISO 128-1:2020 has been approved by CEN as EN ISO 128-1:2020 without any modification.

---------------------- Page: 5 ----------------------
SIST EN ISO 128-1:2020
---------------------- Page: 6 ----------------------
SIST EN ISO 128-1:2020
INTERNATIONAL ISO
STANDARD 128-1
Second edition
2020-05
Technical product documentation
(TPD) — General principles of
representation —
Part 1:
Introduction and fundamental
requirements
Documentation technique de produits (TPD) — Principes généraux de
représentation —
Partie 1: Introduction et exigences fondamentales
Reference number
ISO 128-1:2020(E)
ISO 2020
---------------------- Page: 7 ----------------------
SIST EN ISO 128-1:2020
ISO 128-1:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 128-1:2020
ISO 128-1:2020(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 2

4 Arrangement of the ISO 128 series ................................................................................................................................................... 3

5 Fundamental requirements ...................................................................................................................................................................... 3

6 Basic entities of technical drawings ................................................................................................................................................. 4

6.1 General ........................................................................................................................................................................................................... 4

6.2 Mechanical engineering .................................................................................................................................................................. 4

6.3 Construction engineering .............................................................................................................................................................. 5

6.4 Shipbuilding .............................................................................................................................................................................................. 5

6.5 Materials and processes .................................................................................................................................................................. 5

7 Using the ISO 128 series ............................................................................................................................................................................... 5

Bibliography ................................................................................................................................................................................................................................ 6

© ISO 2020 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 128-1:2020
ISO 128-1:2020(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/ patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/

iso/ foreword .html.

This document was prepared by Technical Committee ISO/TC 10, Technical product documentation, in

collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/SS

F01, Technical drawings, in accordance with the Agreement on technical cooperation between ISO and

CEN (Vienna Agreement).

This second edition cancels and replaces the first edition (ISO 128-1:2003), which has been technically

revised. The main changes to the previous edition are as follows:
— the index has been moved to ISO 128-100;

— references have been updated to point to the revised parts of the ISO 128 series.

A list of all parts in the ISO 128 series can be found on the ISO website.

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 128-1:2020
INTERNATIONAL STANDARD ISO 128-1:2020(E)
Technical product documentation (TPD) — General
principles of representation —
Part 1:
Introduction and fundamental requirements
1 Scope

This document gives general rules for the execution of technical drawings (2D and 3D), as well

as presenting the structure of the other parts of the ISO 128 series. This document is applicable to

technical drawing in the fields of mechanical engineering, construction, architecture and shipbuilding.

It is applicable to both manual and computer-based technical drawings.

For the purpose of this document the term “technical drawing” shall be interpreted in the broadest

possible sense, encompassing the total package of documentation specifying the product (workpiece,

subassembly, assembly).
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

ISO 129 (all parts), Technical product documentation (TPD) — Presentation of dimensions and tolerance

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.