EN 13203-2:2018

Gas-fired domestic appliances producing hot water - Part 2: Assessment of energy consumption

This document is applicable to gas-fired appliances producing domestic hot water. It applies to both instantaneous and storage tank appliances; waters-heaters and combination boilers that have:
- a heat input not exceeding 400 kW; and
- a hot water storage tank capacity (if any) not exceeding 2000 l.
In the case of combination boilers, with or without storage tank, domestic hot water production is integrated or coupled, the whole being marketed as a single unit.
EN 13203-1 sets out in qualitative and quantitative terms the performance in delivery of domestic hot water for a selected variety of uses. It also gives a system for presenting the information to the user. The present document sets out a method for assessing the energy performance of the appliances. It defines a number of daily load profiles for each domestic hot water use, kitchen, shower, bath and a combination of these, together with corresponding test procedures, enabling the energy performances of different gas-fired appliances to be compared and matched to the needs of the user. Where other technologies are combined with a gas-fired boiler or a water heater to produce domestic hot water, specific parts of EN 13203 apply.

Gasbeheizte Geräte für die Warmwasserbereitung für den Hausgebrauch - Teil 2: Bewertung des Energieverbrauchs

Dieses Dokument gilt für gasbeheizte Geräte für die sanitäre Warmwasserbereitung. Sie gilt sowohl für Durchlauferhitzer als auch Warmwasserspeicher, Warmwasserbereiter sowie Kombikessel mit:
-   einer Wärmebelastung von höchstens 400 kW; und
-   einem Warmwasser-Speichervolumen (sofern vorhanden) von höchstens 2 000 l.
Bei Kombikesseln mit oder ohne Speicher ist die sanitäre Warmwasserbereitung im Kessel eingebaut oder am Kessel angebaut; das Gerät wird als eine Gesamteinheit vertrieben.
EN 13203 1 legt mehrere qualitative und quantitative Leistungsstufen für die sanitäre Warmwasserbereitung für eine Auswahl von Benutzungsarten fest. Sie enthält zudem ein System zur Bereitstellung von Informationen für den Nutzer. Dieses Dokument legt ein Verfahren zur Bewertung des Energieverhaltens der Geräte fest. Es definiert eine Anzahl täglicher Lastprofile für die sanitäre Warmwasserverwendung in der Küche, zum Duschen und Baden sowie für Kombinationen dieser Verwendungsarten und legt die entsprechenden Prüfverfahren fest, mit denen sich das Energieverhalten unterschiedlicher gasbeheizter Geräte vergleichen und auf die Bedürfnisse des Nutzers ausrichten lässt. Werden andere Technologien mit einem gasbeheizten Kessel oder einem Warmwasserbereiter für die sanitäre Warmwasserbereitung kombiniert, gelten die jeweils zutreffenden Teile der EN 13203.

Appareils domestiques produisant de l’eau chaude sanitaire utilisant les combustibles gazeux - Partie 2 : Évaluation de la consommation énergétique

Le présent document s’applique aux appareils de production d’eau chaude sanitaire utilisant les combustibles gazeux. Elle s’applique à la fois aux appareils de type instantané et avec ballon, chauffeeau ou chaudières à deux services, qui ont :
- un débit calorifique inférieur ou égal à 400 kW ; et
- une capacité de stockage en eau chaude (le cas échéant) inférieure ou égale à 2 000 l.
Dans le cas des chaudières à deux services avec ou sans ballon, la production d’eau chaude sanitaire est intégrée ou accolée, l’ensemble étant commercialisé comme une seule unité.
L’EN 13203-1 définit en termes qualitatifs et quantitatifs la performance du puisage d’eau chaude sanitaire pour une variété sélectionnée d’usages. Elle fournit également un système pour présenter les informations à l’utilisateur. Le présent document définit une méthode pour évaluer les performances énergétiques des appareils. Il définit plusieurs profils de soutirage journaliers pour chaque utilisation d’eau chaude sanitaire, cuisine, douche, bain et une combinaison de ces derniers, ainsi que les modes
opératoires d’essai correspondants, afin de pouvoir établir une comparaison des performances
énergétiques des appareils utilisant les combustibles gazeux et de les adapter aux besoins de
l’utilisateur. Si d’autres technologies sont combinées avec une chaudière à gaz ou un chauffe-eau pour
produire de l’eau chaude sanitaire, des parties spécifiques de l’EN 13203 s’appliquent.

Plinske gospodinjske naprave za pripravo tople sanitarne vode - 2. del: Ocenjevanje rabe energije

Ta evropski standard se uporablja za plinske gospodinjske naprave za pripravo tople sanitarne vode. uporablja se za pretočne in shranjevalne rezervoarje, grelnike za vodo in kombinirane kotle s:
– toplotno močjo, ki ne presega 70 kW in
– prostornino rezervoarja (če je na voljo) za toplo vodo do 500 l.
Pri kombiniranih kotlih, z rezervoarjem ali brez, je priprava tople vode za gospodinjstva integrirana ali združena, pri čemer se celota trži kot ena enota.
Standard EN 13203-1 v kakovostnem in količinskem smislu določa zmogljivost za pripravo tople sanitarne vode za različne izbrane namene. Zajema tudi sistem za predstavitev informacij uporabniku. Ta dokument določa metodo za ocenjevanje energetske učinkovitosti aparatov. Določa število dnevnih ciklov izpuščanja za vsako uporabo gospodinjske tople vode, kuhinjo, prho, kad in njihove kombinacije, skupaj z ustreznimi preskusnimi postopki, za omogočanje energijske zmogljivosti različnih plinskih naprav za primerjavo in uskladitev s potrebami uporabnika. Posebni deli standarda EN 13203 se uporabljajo, kadar so druge tehnologije združene s plinskimi kotli ali vodnimi grelniki za pripravo tople sanitarne vode.

General Information

• Status: Withdrawn
• Publication Date: 04-Dec-2018
• Withdrawal Date: 09-Aug-2022
• ICS: 91.140.65 - Water heating equipment
• Technical Committee: CEN/TC 109 - Central heating boilers using gaseous fuels
• Drafting Committee: CEN/TC 109/WG 4 - Hot water production of central heating boilers for domestic use
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 10-Aug-2022
• Directive: 2009/125/EC - Directive 2005/32/EC of the European Parliament and of the Council of 6 July 2005 establishing a framework for the setting of ecodesign requirements for energy-using products and amending Council Directive 92/42/EEC and Directives 96/57/EC and 2000/55/EC of the European Parliament and of the Council
• Directive: 2009/142/EC - DIRECTIVE 2009/142/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 30 November 2009 relating to appliances burning gaseous fuels
• Directive: 2010/30/EU - DIRECTIVE 2010/30/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 19 May 2010 on the indication by labelling and standard product information of the consumption of energy and other resources by energy-related products (recast)
• Directive: 80/779/EEC - Air quality limit values and guide values for sulphur dioxide and suspended particulates
• Directive: 811/2013 - Commission Delegated Regulation (EU) No 811/2013 of 18 February 2013 supplementing Directive 2010/30/EU of the European Parliament and of the Council with regard to the energy labelling of space heaters, combination heaters, packages of space heater, temperature control and solar device and packages of combination heater, temperature control and solar device
• Directive: 812/2013 - Commission Delegated Regulation (EU) No 812/2013 of 18 February 2013 supplementing Directive 2010/30/EU of the European Parliament and of the Council with regard to the energy labelling of water heaters, hot water storage tanks and packages of water heater and solar device
• Directive: 813/2013 - Commission Regulation (EU) No 813/2013 of 2 August 2013 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for space heaters and combination heaters
• Directive: 814/2013 - Commission Regulation (EU) No 814/2013 of 2 August 2013 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for water heaters and hot water storage tanks
• Mandate: M/534 - [C(2015)2625] Standardisation request to the European standardisation organisations pursuant to Article 10(1) of Regulation (EU) No 1025/2012 of the European Parliament and of the Council in support of implementation of Commission Regulation (EU) No 814/2013 of 2 August 2013 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for water heaters and hot water storage tanks and Commission Delegated Regulation (EU) No 812/2013 of 18 February 2013 supplementing Directive 2010/30/EU of the European Parliament and of the Council with regard to the energy labelling of water heaters, hot water storage tanks and packages of water heater and solar device
• Mandate: M/535 - [C(2016)2626) Standardisation request to the European standardisation organisations to draft harmonised European standards pursuant to Article 10(1) of Regulation (EU) No 1025/2012 of the European Parliament and of the Council in support of implementation of Commission Regulation (EU) No 813/2013 of 2 August 2013 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to eco-design requirements for space heaters and combination heaters and Commission Delegated Regulation (EU) No 811/2013 of 18 February 2013 supplementing Directive 2010/30/EU of the European Parliament and of the Council with regard to the energy labelling of space heaters, combination heaters, packages of space heaters, temperature control and solar device and packages of combination heater, temperature control and solar device
• Ref Project: SIST EN 13203-2:2019 - Gas-fired domestic appliances producing hot water - Part 2: Assessment of energy consumption

Relations

• Replaces: EN 13203-2:2015 - Gas-fired domestic appliances producing hot water - Part 2: Assessment of energy consumption
• Effective Date: 08-Jun-2022
• Replaced By: EN 13203-2:2022 - Gas-fired domestic appliances producing hot water - Part 2: Assessment of energy consumption
• Effective Date: 05-Aug-2020

Standards Content (Sample)

SLOVENSKI STANDARD
01-april-2019
Nadomešča:
SIST EN 13203-2:2015
Plinske gospodinjske naprave za pripravo tople sanitarne vode - 2. del:
Ocenjevanje rabe energije
Gas-fired domestic appliances producing hot water - Part 2: Assessment of energy
consumption
Gasbeheizte Geräte für die sanitäre Warmwasserbereitung für den Hausgebrauch - Teil
2: Bewertung des Energieverbrauchs
Appareils domestiques produisant de l'eau chaude sanitaire utilisant les combustibles
gazeux - Partie 2 : Evaluation de la consommation énergétique
Ta slovenski standard je istoveten z: EN 13203-2:2018
ICS:
91.140.65 Oprema za ogrevanje vode Water heating equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 13203-2
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2018
EUROPÄISCHE NORM
ICS 91.140.65 Supersedes EN 13203-2:2015
English Version
Gas-fired domestic appliances producing hot water - Part
2: Assessment of energy consumption
Appareils domestiques produisant de l'eau chaude Gasbeheizte Geräte für die sanitäre
sanitaire utilisant les combustibles gazeux - Partie 2 : Warmwasserbereitung für den Hausgebrauch - Teil 2:
Évaluation de la consommation énergétique Bewertung des Energieverbrauchs
This European Standard was approved by CEN on 26 October 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13203-2:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 General test conditions . 8
4.1 Reference conditions . 8
4.2 Measurement uncertainties . 8
4.2.1 General . 8
4.2.2 Steady state conditions . 9
4.3 Test conditions . 9
4.3.1 General . 9
4.3.2 Test room . 9
4.3.3 Water supply . 9
4.3.4 Initial adjustment of the appliance . 10
4.3.5 Conditions for the determination of the maximum load profile . 10
4.3.6 Electrical supply . 10
5 Determination of the energy consumption of the appliance . 11
5.1 General . 11
5.2 Load profiles . 11
5.3 Determination of the energy recovered by the useful water . 18
5.4 Calculation of gas energy . 19
5.4.1 Calculation of daily gas energy consumption in summer mode . 19
5.4.2 Calculation of daily gas energy consumption in winter mode . 19
5.4.3 Daily gas energy consumption seasonally weighted . 20
5.5 Calculation of daily electrical energy consumption . 20
5.6 Measurement of energy consumption in standby mode . 21
5.6.1 General . 21
5.6.2 Calculation of daily gas energy consumption in standby mode . 21
5.6.3 Calculation of daily auxiliary electrical energy consumption in standby mode . 22
5.7 Determination of daily auxiliary electrical energy consumption in off mode . 22
6 Determination of the ratio of wasted water to total water . 22
7 Eco design Related Products Data . 23
7.1 Water heating energy efficiency . 23
7.2 Annual fuel consumption (AFC) . 24
7.3 Annual electricity consumption (AEC) . 25
7.4 Mixed water at 40°C (V40) for storage water heaters . 25
Annex A (informative)  Test conditions . 28
Annex B (informative)  Test rig and measurement devices . 31
B.1 General . 31
B.2 Pressure measurement . 32
B.3 Temperature measurement . 32
Annex C (informative) Declaration of the Maximum Load Profile . 36
Annex ZA (informative) Relationship between this European Standard and the ecodesign
requirements of Commission Regulation (EU) n° 814/2013 [OJEU L239 of 6 September
2013] aimed to be covered . 37
Annex ZB (informative) Relationship between this European Standard and the energy labelling
requirements of Commission Delegated Regulation (EU) No 812/2013 [OJEU L239 of 6
September 2013] aimed to be covered . 38
Annex ZC (informative) Relationship between this European Standard and the ecodesign
requirements of Commission Regulation (EU) n° 813/2013 [OJEU L239 of 6 September
2013] aimed to be covered . 39
Annex ZD (informative) Relationship between this European Standard and the energy labelling
requirements of Commission Delegated Regulation (EU) No 811/2013 [OJEU L239 of 6
September 2013] aimed to be covered . 40
Bibliography . 41
European foreword
This document (EN 13203-2:2018) has been prepared by Technical Committee CEN/TC 109 "Central heating
boilers using gaseous fuels", the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2019, and conflicting national standards shall be withdrawn at
the latest by June 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13203-2:2015.
The main technical changes compared to EN 13203-2:2015 are the following:
— improvement of the test conditions (e.g. water supply, initial adjustment of the appliance);
— addition of further load profile XS for small appliances;
— addition of new clause dealing with mixed water at 40°C (V40) for storage water heaters and
corresponding complement to Annex ZA (informative);
— addition of new Annex C (informative) dealing with the declaration of the maximum load profile.
The main purpose of this revision is to provide a means of conforming to requirements of Commission
Delegated Regulation (EC) n° 813/2013, (EC) n° 811/2013, (EC) n° 812/2013 and (EC) n° 814/2013.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Regulation(s).
For relationship with EU Directive(s), see informative Annex ZA, ZB, ZC or ZD, which are an integral part of
this document.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Introduction
The safety operation of the boiler or water heater is not covered by this standard. Safety should be proved by
means of the essential safety requirements of the Gas Appliances Regulation 2016/426/UE. This may be
achieved by compliance with the appropriate existing harmonized standards.
NOTE Useful standards are EN 26, EN 89, EN 15502-1, EN 15502-2-1 and EN 15502-2-2.
1 Scope
This document is applicable to gas-fired appliances producing domestic hot water. It applies to both
instantaneous and storage tank appliances; waters-heaters and combination boilers that have:
— a heat input not exceeding 400 kW; and
— a hot water storage tank capacity (if any) not exceeding 2000 l.
In the case of combination boilers, with or without storage tank, domestic hot water production is integrated
or coupled, the whole being marketed as a single unit.
EN 13203-1 sets out in qualitative and quantitative terms the performance in delivery of domestic hot water
for a selected variety of uses. It also gives a system for presenting the information to the user. The present
document sets out a method for assessing the energy performance of the appliances. It defines a number of
daily load profiles for each domestic hot water use, kitchen, shower, bath and a combination of these, together
with corresponding test procedures, enabling the energy performances of different gas-fired appliances to be
compared and matched t
...

SLOVENSKI STANDARD
01-april-2019
1DGRPHãþD
SIST EN 13203-2:2015
Plinske gospodinjske naprave za pripravo tople sanitarne vode - 2. del:
Ocenjevanje zmogljivosti rabe energije
Gas-fired domestic appliances producing hot water - Part 2: Assessment of energy
consumption
Gasbeheizte Geräte für die sanitäre Warmwasserbereitung für den Hausgebrauch - Teil
2: Bewertung des Energieverbrauchs
Appareils domestiques produisant de l'eau chaude sanitaire utilisant les combustibles
gazeux - Partie 2 : Evaluation de la consommation énergétique
Ta slovenski standard je istoveten z: EN 13203-2:2018
ICS:
91.140.65 Oprema za ogrevanje vode Water heating equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 13203-2
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2018
EUROPÄISCHE NORM
ICS 91.140.65 Supersedes EN 13203-2:2015
English Version
Gas-fired domestic appliances producing hot water - Part
2: Assessment of energy consumption
Appareils domestiques produisant de l'eau chaude Gasbeheizte Geräte für die sanitäre
sanitaire utilisant les combustibles gazeux - Partie 2 : Warmwasserbereitung für den Hausgebrauch - Teil 2:
Évaluation de la consommation énergétique Bewertung des Energieverbrauchs
This European Standard was approved by CEN on 26 October 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13203-2:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 General test conditions . 8
4.1 Reference conditions . 8
4.2 Measurement uncertainties . 8
4.2.1 General . 8
4.2.2 Steady state conditions . 9
4.3 Test conditions . 9
4.3.1 General . 9
4.3.2 Test room . 9
4.3.3 Water supply . 9
4.3.4 Initial adjustment of the appliance . 10
4.3.5 Conditions for the determination of the maximum load profile . 10
4.3.6 Electrical supply . 10
5 Determination of the energy consumption of the appliance . 11
5.1 General . 11
5.2 Load profiles . 11
5.3 Determination of the energy recovered by the useful water . 18
5.4 Calculation of gas energy . 19
5.4.1 Calculation of daily gas energy consumption in summer mode . 19
5.4.2 Calculation of daily gas energy consumption in winter mode . 19
5.4.3 Daily gas energy consumption seasonally weighted . 20
5.5 Calculation of daily electrical energy consumption . 20
5.6 Measurement of energy consumption in standby mode . 21
5.6.1 General . 21
5.6.2 Calculation of daily gas energy consumption in standby mode . 21
5.6.3 Calculation of daily auxiliary electrical energy consumption in standby mode . 22
5.7 Determination of daily auxiliary electrical energy consumption in off mode . 22
6 Determination of the ratio of wasted water to total water . 22
7 Eco design Related Products Data . 23
7.1 Water heating energy efficiency . 23
7.2 Annual fuel consumption (AFC) . 24
7.3 Annual electricity consumption (AEC) . 25
7.4 Mixed water at 40°C (V40) for storage water heaters . 25
Annex A (informative)  Test conditions . 28
Annex B (informative)  Test rig and measurement devices . 31
B.1 General . 31
B.2 Pressure measurement . 32
B.3 Temperature measurement . 32
Annex C (informative) Declaration of the Maximum Load Profile . 36
Annex ZA (informative) Relationship between this European Standard and the ecodesign
requirements of Commission Regulation (EU) n° 814/2013 [OJEU L239 of 6 September
2013] aimed to be covered . 37
Annex ZB (informative) Relationship between this European Standard and the energy labelling
requirements of Commission Delegated Regulation (EU) No 812/2013 [OJEU L239 of 6
September 2013] aimed to be covered . 38
Annex ZC (informative) Relationship between this European Standard and the ecodesign
requirements of Commission Regulation (EU) n° 813/2013 [OJEU L239 of 6 September
2013] aimed to be covered . 39
Annex ZD (informative) Relationship between this European Standard and the energy labelling
requirements of Commission Delegated Regulation (EU) No 811/2013 [OJEU L239 of 6
September 2013] aimed to be covered . 40
Bibliography . 41
European foreword
This document (EN 13203-2:2018) has been prepared by Technical Committee CEN/TC 109 "Central heating
boilers using gaseous fuels", the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2019, and conflicting national standards shall be withdrawn at
the latest by June 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13203-2:2015.
The main technical changes compared to EN 13203-2:2015 are the following:
— improvement of the test conditions (e.g. water supply, initial adjustment of the appliance);
— addition of further load profile XS for small appliances;
— addition of new clause dealing with mixed water at 40°C (V40) for storage water heaters and
corresponding complement to Annex ZA (informative);
— addition of new Annex C (informative) dealing with the declaration of the maximum load profile.
The main purpose of this revision is to provide a means of conforming to requirements of Commission
Delegated Regulation (EC) n° 813/2013, (EC) n° 811/2013, (EC) n° 812/2013 and (EC) n° 814/2013.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Regulation(s).
For relationship with EU Directive(s), see informative Annex ZA, ZB, ZC or ZD, which are an integral part of
this document.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Introduction
The safety operation of the boiler or water heater is not covered by this standard. Safety should be proved by
means of the essential safety requirements of the Gas Appliances Regulation 2016/426/UE. This may be
achieved by compliance with the appropriate existing harmonized standards.
NOTE Useful standards are EN 26, EN 89, EN 15502-1, EN 15502-2-1 and EN 15502-2-2.
1 Scope
This document is applicable to gas-fired appliances producing domestic hot water. It applies to both
instantaneous and storage tank appliances; waters-heaters and combination boilers that have:
— a heat input not exceeding 400 kW; and
— a hot water storage tank capacity (if any) not exceeding 2000 l.
In the case of combination boilers, with or without storage tank, domestic hot water production is integrated
or coupled, the whole being marketed as a single unit.
EN 13203-1 sets out in qualitative and quantitative terms the performance in delivery of domestic hot water
for a selected variety of uses. It also gives a system for presenting the information to the user. The present
document sets out a method for assessing the energy performance of the appliances. It defines a number of
daily load profiles for each domestic hot water use, kitchen, shower, bath and a combination of these, together
with corresponding test procedures, enabling the energy performances of different gas-fired appliances to
...