EN ISO 16534:2020
(Main)Thermal insulating products for building applications - Determination of compressive creep (ISO 16534:2020)
Thermal insulating products for building applications - Determination of compressive creep (ISO 16534:2020)
This document specifies the equipment and test method for determining the compressive creep of specimens under various conditions of stress.
This document is applicable to thermal insulating products.
Wärmedämmstoffe für das Bauwesen - Bestimmung des Langzeit-Kriechverhaltens bei Druckbeanspruchung (ISO 16534:2020)
Dieses Dokument legt Prüfeinrichtungen und das Prüfverfahren zur Bestimmung des Kriechverhaltens von Probekörpern bei Druckbeanspruchung mit verschiedenen Laststufen fest.
Dieses Dokument gilt für Wärmedämmstoffe.
Produits isolants thermiques destinés aux applications du bâtiment - Détermination du fluage en compression (ISO 16534:2020)
Le présent document spécifie l'équipement et les méthodes d'essai permettant de déterminer le fluage en compression d'éprouvettes soumises à différentes conditions de contrainte.
Le présent document s'applique aux produits isolants thermiques.
Toplotnoizolacijski proizvodi za uporabo v gradbeništvu - Ugotavljanje lezenja pod tlačno obremenitvijo (ISO 16534:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2020
Toplotnoizolacijski proizvodi za uporabo v gradbeništvu - Ugotavljanje lezenja pod
tlačno obremenitvijo (ISO 16534:2020)
Thermal insulating products for building applications - Determination of compressive
creep (ISO 16534:2020)
Wärmedämmstoffe für das Bauwesen - Bestimmung des Langzeit-Kriechverhaltens bei
Druckbeanspruchung (ISO 16534:2020)
Produits isolants thermiques destinés aux applications du bâtiment - Détermination du
fluage en compression (ISO 16534:2020)
Ta slovenski standard je istoveten z: EN ISO 16534:2020
ICS:
91.100.60 Materiali za toplotno in Thermal and sound insulating
zvočno izolacijo materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 16534
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2020
EUROPÄISCHE NORM
ICS 91.100.60
English Version
Thermal insulating products for building applications -
Determination of compressive creep (ISO 16534:2020)
Produits isolants thermiques destinés aux applications Wärmedämmstoffe für das Bauwesen - Bestimmung
du bâtiment - Détermination du fluage en compression des Langzeit-Kriechverhaltens bei
(ISO 16534:2020) Druckbeanspruchung (ISO 16534:2020)
This European Standard was approved by CEN on 22 June 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16534:2020 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 16534:2020) has been prepared by Technical Committee ISO/TC 163 "Thermal
performance and energy use in the built environment" in collaboration with Technical Committee
CEN/TC 88 “Thermal insulating materials and products” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2021, and conflicting national standards shall
be withdrawn at the latest by January 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 16534:2020 has been approved by CEN as EN ISO 16534:2020 without any modification.
INTERNATIONAL ISO
STANDARD 16534
Second edition
2020-06
Thermal insulating products
for building applications —
Determination of compressive creep
Produits isolants thermiques destinés aux applications du bâtiment —
Détermination du fluage en compression
Reference number
ISO 16534:2020(E)
©
ISO 2020
ISO 16534:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
ISO 16534:2020(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 3
5 Principle . 3
6 Apparatus . 3
7 Test specimens. 4
7.1 Selection of test specimens . 4
7.2 Dimensions of test specimens . 4
7.3 Number of test specimens . 5
7.4 Preparation of test specimens . 5
7.5 Conditioning of test specimens . 5
8 Procedure. 5
8.1 Test conditions . 5
8.2 Stress selection . 6
8.3 Test procedure . 6
8.4 Duration of test . 8
9 Calculation and expression of results . 8
10 Accuracy of measurement . 8
11 Test report . 8
Annex A (normative) Calculation method .10
Annex B (informative) Example of a linear regression analysis .13
Bibliography .16
ISO 16534:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee Committee ISO/TC 163, Thermal performance and
energy use in the built environment, Subcommittee SC 1, Test and measurement methods, in collaboration
with the European Committee for Standardization (CEN) Technical Committee CEN/TC 88, Thermal
insulating materials and products, in accordance with the Agreement on technical cooperation between
ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 16546:2012), which has been technically
revised. The main changes compared to the previous edition are as follows:
— modification of Figure 1;
— editorial modifications.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved
INTERNATIONAL STANDARD ISO 16534:2020(E)
Thermal insulating products for building applications —
Determination of compressive creep
1 Scope
This document specifies the equipment and test method for determining the compressive creep of
specimens under various conditions of stress.
This document is applicable to thermal insulating products.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 29469, Thermal insulating products for building applications — Determination of compression
behaviour
ISO 29768, Thermal insulating products for building applications — Determination of linear dimensions of
test spec
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.