EN ISO 4064-4:2014

Water meters for cold potable water and hot water - Part 4: Non-metrological requirements not covered in ISO 4064-1 (ISO 4064-4:2014)

ISO 4064-4:2014 applies to water meters used to meter the volume of cold potable water and hot water flowing through a fully charged, closed conduit. These water meters incorporate devices which indicate the integrated volume.
ISO 4064-4:2014 specifies technical characteristics and pressure loss requirements for meters for cold potable water and hot water. It applies to water meters which can withstand: a) a maximum admissible working pressure (MAP) equal to at least 1 MPa [0,6 MPa for meters for use with pipe nominal diameters (DNs) ≥500 mm]; b) a maximum admissible temperature (MAT) for cold potable water meters of 30 °C; c) a MAT for hot water meters up to 180 °C, depending on class.
In addition to meters based on mechanical principles, ISO 4064-4:2014 also applies to water meters based on electrical or electronic principles, and to water meters based on mechanical principles incorporating electronic devices, used to meter the volume flow of hot water and cold potable water. It also applies to electronic ancillary devices. As a rule ancillary devices are optional. However, national or international regulations may make some ancillary devices mandatory in relation to the utilization of the water meter.

Wasserzähler zum Messen von kaltem Trinkwasser und heißem Wasser - Teil 4: Nichtmetrologische Anforderungen, die nicht Gegenstand von ISO 4064-1 sind (ISO 4064-4:2014)

Dieser Teil von ISO 4064 gilt für Wasserzähler zur Volumenmessung von kaltem Trinkwasser und heißem Wasser, das durch eine vollständig gefüllte, geschlossene Leitung fließt. Diese Wasserzähler müssen mit Einrichtungen versehen sein, die das kumulierte Volumen anzeigen.
Dieser Teil von ISO 4064 legt technische Eigenschaften und Anforderungen für den Druckverlust für Wasser-zähler für kaltes Trinkwasser und heißes Wasser fest. Sie gilt für Wasserzähler,
a)   die dem größten zulässigen Druck (MAP)  1 MPa ) [0,6 MPa bei Zählern für Rohre mit Nenndurchmessern (DN)  500 mm],
b)   die der höchsten zulässigen Temperatur (MAT) von 30 °C für Wasserzähler für kaltes Trinkwasser,
c)   die der höchsten zulässigen Temperatur (MAT), in Abhängigkeit von der jeweiligen Klasse, von bis zu 180 °C für Wasserzähler für heißes Wasser
widerstehen können.
Zusätzlich zu den auf mechanischen Funktionsprinzipien beruhenden Wasserzählern gilt der vorliegende Teil der ISO 4064 ebenfalls für Wasserzähler, die auf elektrischen oder elektronischen Funktionsprinzipien beruhen und für Wasserzähler nach mechanischen Funktionsprinzipien mit elektronischen Einrichtungen, die zur Messung des Volumendurchflusses von heißem Wasser und von kaltem Trinkwasser dienen. Er gilt außerdem für elektro-nische Zusatzeinrichtungen. Zusatzeinrichtungen sind grundsätzlich optional. Jedoch können in nationalen oder internationalen Vorschriften einige Zusatzeinrichtungen hinsichtlich der Verwendung von Wasserzählern verbindlich vorgeschrieben sein.

Compteurs d'eau potable froide et d'eau chaude - Partie 4: Exigences non métrologiques non couvertes par l'ISO 4064-1 (ISO 4064-4:2014)

L'ISO 4064-4:2013 s'applique aux compteurs d'eau utilisés pour mesurer le volume d'eau potable froide et d'eau chaude s'écoulant dans une conduite fermée et à pleine charge. Ces compteurs d'eau comportent des dispositifs indiquant le volume compté.
L'ISO 4064-4:2013 spécifie les paramètres techniques et les exigences de perte de pression s'appliquant aux compteurs d'eau potable froide et d'eau chaude. Elle s'applique aux compteurs d'eau pouvant résister à: a) une pression de service maximale admissible (PMA) égale à au moins 1 MPa [0,6 MPa pour les compteurs équipant des conduites de diamètre nominal (DN) ≥ 500 mm]; b) à une température maximale admissible (TMA) allant de 30 ºC, pour les compteurs d'eau potable froide; c) jusqu'à 180 ºC pour les compteurs d'eau chaude, selon la classe.
En plus des compteurs dont le fonctionnement est basé sur des principes mécaniques, l'ISO 4064-4:2013 s'applique aussi aux compteurs d'eau dont le fonctionnement est basé sur un principe électrique ou électronique, ainsi qu'aux compteurs d'eau à fonctionnement mécanique incluant des dispositifs électroniques utilisés pour mesurer le volume débité d'eau chaude et d'eau potable froide. Elle s'applique également aux dispositifs électroniques auxiliaires. Généralement, les dispositifs auxiliaires sont facultatifs. Cependant, des réglementations nationales ou internationales peuvent rendre certains dispositifs auxiliaires obligatoires selon l'utilisation du compteur d'eau.

Vodomeri za merjenje hladne pitne vode in vroče vode - 4. del: Nemetrološke zahteve, ki niso zajete v ISO 4064-1 (ISO 4064-4:2014)

Standard EN ISO 4064-4 se uporablja za vodomere za merjenje pretoka hladne pitne vode in vroče vode, ki teče skozi zaprto cev s polnim pretokom. Ti vodomeri imajo vgrajene naprave, ki prikazujejo vgrajen pretok. Ta del standarda ISO 4064 določa tehnične lastnosti in zahteve za izgubo tlaka pri vodomerih za hladno pitno vodo in vročo vodo. Uporablja se za vodomere, ki lahko prenesejo: a) največji dovoljeni tlak (MAP), ki je enak najmanj 1 MPa) [0,6 MPa za vodomere za uporabo s cevmi z nazivnimi premeri (DN) ≥500 mm], b) največjo dovoljeno temperaturo (MAT) za vodomere za hladno pitno vodo 30 °C, c) MAT za vodomere za vročo vodo do 180 °C, odvisno od vrste. Poleg mehansko delujočih vodomerov se ta del standarda ISO 4064 uporablja za električno ali elektronsko delujoče vodomere in vodomere, delujoče na podlagi mehanskih načel z vgrajenimi elektronskimi napravami, ki se uporabljajo za merjenje pretoka hladne pitne vode in vroče vode. Uporablja se tudi za elektronske pomožne naprave. Praviloma so pomožne naprave izbirne. Kljub temu lahko nacionalni ali mednarodni predpisi določajo obvezno uporabo nekaterih pomožnih naprav v povezavi z uporabo vodomerov.

General Information

• Status: Published
• Publication Date: 03-Jun-2014
• Withdrawal Date: 29-Jun-2017
• ICS: 91.140.60 - Water supply systems
• Technical Committee: CEN/TC 92 - Test methods and equipment for cold water meters
• Drafting Committee: CEN/TC 92 - Test methods and equipment for cold water meters
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 04-Jun-2014
• Completion Date: 04-Jun-2014
• Directive: 2004/22/EC - Directive 2004/22/EC of the European Parliament and of the Council of 31 March 2004 on measuring instruments
• Mandate: M/374 - Mandate to CEN and CENELEC for standards in the field of measuring instruments
• Ref Project: SIST EN ISO 4064-4:2014 - Water meters for cold potable water and hot water - Part 4: Non- metrological requirements not covered in ISO 4064-1 (ISO 4064- 4:2014)

Relations

• Replaces: EN 14154-1:2005+A2:2011 - Water meters - Part 1: General requirements
• Effective Date: 08-Jun-2022
• Revised: prEN ISO 4064-4 - Water meters for cold potable water and hot water - Part 4: Non-metrological requirements not covered in ISO 4064-1 (ISO/DIS 4064-4:2023)
• Effective Date: 21-Dec-2022
• Revised: EN 14154-3:2005+A1:2007 - Water meters - Part 3: Test methods and equipment
• Effective Date: 24-Oct-2009
• Revised: EN 14154-1:2005+A1:2007 - Water meters - Part 1: General requirements
• Effective Date: 24-Oct-2009
• Revised: EN 14154-2:2005+A1:2007 - Water meters - Part 2: Installation and conditions of use
• Effective Date: 24-Oct-2009

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 4064-4:2014
01-julij-2014
1DGRPHãþD
SIST EN 14154-1:2005+A2:2011
SIST EN 14154-2:2005+A2:2011
SIST EN 14154-3:2005+A2:2011
9RGRPHUL]DPHUMHQMHKODGQHSLWQHYRGHLQYURþHYRGHGHO1HPHWURORãNH
]DKWHYHNLQLVR]DMHWHY,62,62
Water meters for cold potable water and hot water - Part 4: Non- metrological
requirements not covered in ISO 4064-1 (ISO 4064- 4:2014)
Wasserzähler zum Messen von kaltem Trinkwasser und heißem Wasser - Teil 4:
Nichtmetrologische Anforderungen, die nicht Gegenstand von ISO 4064-1 sind (ISO
4064- 4:2014)
Compteurs d'eau destinés au mesurage de l'eau potable froide et chaude - Partie 4:
Exigences non métrologiques non couvertes par l'ISO 4064-1 (ISO 4064- 4:2014)
Ta slovenski standard je istoveten z: EN ISO 4064-4:2014
ICS:
17.120.10 Pretok v zaprtih vodih Flow in closed conduits
91.140.60 Sistemi za oskrbo z vodo Water supply systems
SIST EN ISO 4064-4:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 4064-4:2014

---------------------- Page: 2 ----------------------

SIST EN ISO 4064-4:2014

EUROPEAN STANDARD
EN ISO 4064-4

NORME EUROPÉENNE

EUROPÄISCHE NORM
June 2014
ICS 91.140.60 Supersedes EN 14154-1:2005+A2:2011, EN 14154-
2:2005+A2:2011, EN 14154-3:2005+A2:2011
English Version
Water meters for cold potable water and hot water - Part 4: Non-
metrological requirements not covered in ISO 4064-1 (ISO 4064-
4:2014)
Compteurs d'eau potable froide et d'eau chaude - Partie 4: Wasserzähler zum Messen von kaltem Trinkwasser und
Exigences non métrologiques non couvertes par l'ISO heißem Wasser - Teil 4: Nichtmetrologische Anforderungen,
4064-1 (ISO 4064-4:2014) die nicht Gegenstand von ISO 4064-1 sind (ISO 4064-
4:2014)
This European Standard was approved by CEN on 21 September 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4064-4:2014 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 4064-4:2014
EN ISO 4064-4:2014 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 4064-4:2014
EN ISO 4064-4:2014 (E)
Foreword
This document (EN ISO 4064-4:2014) has been prepared by Technical Committee ISO/TC 30 “Measurement
of fluid flow in closed conduits” in collaboration with Technical Committee CEN/TC 92 “Water meters” the
secretariat of which is held by SNV.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2014, and conflicting national standards shall be withdrawn
at the latest by December 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 14154-1:2005+A2:2011, EN 14154-2:2005+A2:2011,
EN 14154-3:2005+A2:2011.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherla
...